Initial commit

LED/Drivers/CMSIS/Device/ST/STM32F0xx/Include/stm32f0xx.h

@@ -0,0 +1,236 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx.h
+  * @author  MCD Application Team
+  * @brief   CMSIS STM32F0xx Device Peripheral Access Layer Header File.           
+  *            
+  *          The file is the unique include file that the application programmer
+  *          is using in the C source code, usually in main.c. This file contains:
+  *           - Configuration section that allows to select:
+  *              - The STM32F0xx device used in the target application
+  *              - To use or not the peripheral’s drivers in application code(i.e. 
+  *                code will be based on direct access to peripheral’s registers 
+  *                rather than drivers API), this option is controlled by 
+  *                "#define USE_HAL_DRIVER"
+  *  
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/** @addtogroup CMSIS
+  * @{
+  */
+
+/** @addtogroup stm32f0xx
+  * @{
+  */
+    
+#ifndef __STM32F0xx_H
+#define __STM32F0xx_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif /* __cplusplus */
+   
+/** @addtogroup Library_configuration_section
+  * @{
+  */
+  
+/**
+  * @brief STM32 Family
+  */
+#if !defined  (STM32F0)
+#define STM32F0
+#endif /* STM32F0 */
+
+/** Uncomment the line below according to the target STM32 device used in your application.
+  * stm32f0xxxx.h file contains:
+  * - All the peripheral register's definitions, bits definitions and memory mapping for STM32F0xxxx devices
+  * - IRQ channel definition
+  * - Peripheral memory mapping and physical registers address definition
+  * - Peripheral pointer declaration and driver header file inclusion
+  * - Product miscellaneous configuration: assert macros…
+  * Note: These CMSIS drivers (stm32f0xxxx.h) are always supporting features of the sub-family’s superset.
+  */
+
+#if !defined (STM32F030x6) && !defined (STM32F030x8) &&                           \
+    !defined (STM32F031x6) && !defined (STM32F038xx) &&                           \
+    !defined (STM32F042x6) && !defined (STM32F048xx) && !defined (STM32F070x6) && \
+    !defined (STM32F051x8) && !defined (STM32F058xx) &&                           \
+    !defined (STM32F071xB) && !defined (STM32F072xB) && !defined (STM32F078xx) && !defined (STM32F070xB) && \
+    !defined (STM32F091xC) && !defined (STM32F098xx) && !defined (STM32F030xC)
+  /* #define STM32F030x6 */  /*!< STM32F030x4, STM32F030x6 Devices (STM32F030xx microcontrollers where the Flash memory ranges between 16 and 32 Kbytes)              */
+  /* #define STM32F030x8 */  /*!< STM32F030x8 Devices (STM32F030xx microcontrollers where the Flash memory is 64 Kbytes)                                              */
+  /* #define STM32F031x6 */  /*!< STM32F031x4, STM32F031x6 Devices (STM32F031xx microcontrollers where the Flash memory ranges between 16 and 32 Kbytes)              */
+  /* #define STM32F038xx */  /*!< STM32F038xx Devices (STM32F038xx microcontrollers where the Flash memory is 32 Kbytes)                                              */
+  /* #define STM32F042x6 */  /*!< STM32F042x4, STM32F042x6 Devices (STM32F042xx microcontrollers where the Flash memory ranges between 16 and 32 Kbytes)              */
+  /* #define STM32F048xx */  /*!< STM32F048xx Devices (STM32F048xx microcontrollers where the Flash memory is 32 Kbytes)                                              */
+  /* #define STM32F051x8 */  /*!< STM32F051x4, STM32F051x6, STM32F051x8 Devices (STM32F051xx microcontrollers where the Flash memory ranges between 16 and 64 Kbytes) */
+  /* #define STM32F058xx */  /*!< STM32F058xx Devices (STM32F058xx microcontrollers where the Flash memory is 64 Kbytes)                                              */
+  /* #define STM32F070x6 */  /*!< STM32F070x6 Devices (STM32F070x6 microcontrollers where the Flash memory ranges between 16 and 32 Kbytes)                           */
+  /* #define STM32F070xB */  /*!< STM32F070xB Devices (STM32F070xB microcontrollers where the Flash memory ranges between 64 and 128 Kbytes)                          */
+  /* #define STM32F071xB */  /*!< STM32F071x8, STM32F071xB Devices (STM32F071xx microcontrollers where the Flash memory ranges between 64 and 128 Kbytes)             */
+  /* #define STM32F072xB */  /*!< STM32F072x8, STM32F072xB Devices (STM32F072xx microcontrollers where the Flash memory ranges between 64 and 128 Kbytes)             */
+  /* #define STM32F078xx */  /*!< STM32F078xx Devices (STM32F078xx microcontrollers where the Flash memory is 128 Kbytes)                                             */
+  /* #define STM32F030xC */  /*!< STM32F030xC Devices (STM32F030xC microcontrollers where the Flash memory is 256 Kbytes)                                             */  
+  /* #define STM32F091xC */  /*!< STM32F091xB, STM32F091xC Devices (STM32F091xx microcontrollers where the Flash memory ranges between 128 and 256 Kbytes)            */
+  /* #define STM32F098xx */  /*!< STM32F098xx Devices (STM32F098xx microcontrollers where the Flash memory is 256 Kbytes)                                             */
+#endif
+/* Legacy aliases */
+#if defined (STM32F048x6)
+ #define STM32F048xx 
+#endif /* STM32F048x6 */
+
+/*  Tip: To avoid modifying this file each time you need to switch between these
+        devices, you can define the device in your toolchain compiler preprocessor.
+  */
+#if !defined  (USE_HAL_DRIVER)
+/**
+ * @brief Comment the line below if you will not use the peripherals drivers.
+   In this case, these drivers will not be included and the application code will 
+   be based on direct access to peripherals registers 
+   */
+  /*#define USE_HAL_DRIVER */
+#endif /* USE_HAL_DRIVER */
+
+/**
+  * @brief CMSIS Device version number V2.3.5
+  */
+#define __STM32F0_DEVICE_VERSION_MAIN   (0x02) /*!< [31:24] main version */
+#define __STM32F0_DEVICE_VERSION_SUB1   (0x03) /*!< [23:16] sub1 version */
+#define __STM32F0_DEVICE_VERSION_SUB2   (0x05) /*!< [15:8]  sub2 version */
+#define __STM32F0_DEVICE_VERSION_RC     (0x00) /*!< [7:0]  release candidate */ 
+#define __STM32F0_DEVICE_VERSION        ((__STM32F0_DEVICE_VERSION_MAIN << 24)\
+                                        |(__STM32F0_DEVICE_VERSION_SUB1 << 16)\
+                                        |(__STM32F0_DEVICE_VERSION_SUB2 << 8 )\
+                                        |(__STM32F0_DEVICE_VERSION_RC))
+                                             
+/**
+  * @}
+  */
+
+/** @addtogroup Device_Included
+  * @{
+  */
+
+#if defined(STM32F030x6)
+  #include "stm32f030x6.h"
+#elif defined(STM32F030x8)
+  #include "stm32f030x8.h"
+#elif defined(STM32F031x6)
+  #include "stm32f031x6.h"
+#elif defined(STM32F038xx)
+  #include "stm32f038xx.h"
+#elif defined(STM32F042x6)
+  #include "stm32f042x6.h"
+#elif defined(STM32F048xx)
+  #include "stm32f048xx.h"
+#elif defined(STM32F051x8)
+  #include "stm32f051x8.h"
+#elif defined(STM32F058xx)
+  #include "stm32f058xx.h"
+#elif defined(STM32F070x6)
+  #include "stm32f070x6.h"
+#elif defined(STM32F070xB)
+  #include "stm32f070xb.h"
+#elif defined(STM32F071xB)
+  #include "stm32f071xb.h"
+#elif defined(STM32F072xB)
+  #include "stm32f072xb.h"
+#elif defined(STM32F078xx)
+  #include "stm32f078xx.h"
+#elif defined(STM32F091xC)
+  #include "stm32f091xc.h"
+#elif defined(STM32F098xx)
+  #include "stm32f098xx.h"
+#elif defined(STM32F030xC)
+  #include "stm32f030xc.h"    
+#else
+ #error "Please select first the target STM32F0xx device used in your application (in stm32f0xx.h file)"
+#endif
+
+/**
+  * @}
+  */
+
+/** @addtogroup Exported_types
+  * @{
+  */ 
+typedef enum 
+{
+  RESET = 0U, 
+  SET = !RESET
+} FlagStatus, ITStatus;
+
+typedef enum 
+{
+  DISABLE = 0U, 
+  ENABLE = !DISABLE
+} FunctionalState;
+#define IS_FUNCTIONAL_STATE(STATE) (((STATE) == DISABLE) || ((STATE) == ENABLE))
+
+typedef enum 
+{
+  SUCCESS = 0U,
+  ERROR = !SUCCESS
+} ErrorStatus;
+
+/**
+  * @}
+  */
+
+
+/** @addtogroup Exported_macros
+  * @{
+  */
+#define SET_BIT(REG, BIT)     ((REG) |= (BIT))
+
+#define CLEAR_BIT(REG, BIT)   ((REG) &= ~(BIT))
+
+#define READ_BIT(REG, BIT)    ((REG) & (BIT))
+
+#define CLEAR_REG(REG)        ((REG) = (0x0))
+
+#define WRITE_REG(REG, VAL)   ((REG) = (VAL))
+
+#define READ_REG(REG)         ((REG))
+
+#define MODIFY_REG(REG, CLEARMASK, SETMASK)  WRITE_REG((REG), (((READ_REG(REG)) & (~(CLEARMASK))) | (SETMASK)))
+
+
+/**
+  * @}
+  */
+
+#if defined (USE_HAL_DRIVER)
+ #include "stm32f0xx_hal.h"
+#endif /* USE_HAL_DRIVER */
+
+
+#ifdef __cplusplus
+}
+#endif /* __cplusplus */
+
+#endif /* __STM32F0xx_H */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/CMSIS/Device/ST/STM32F0xx/Include/system_stm32f0xx.h

@@ -0,0 +1,105 @@
+/**
+  ******************************************************************************
+  * @file    system_stm32f0xx.h
+  * @author  MCD Application Team
+  * @brief   CMSIS Cortex-M0 Device System Source File for STM32F0xx devices.  
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/** @addtogroup CMSIS
+  * @{
+  */
+
+/** @addtogroup stm32f0xx_system
+  * @{
+  */  
+  
+/**
+  * @brief Define to prevent recursive inclusion
+  */
+#ifndef __SYSTEM_STM32F0XX_H
+#define __SYSTEM_STM32F0XX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif 
+
+/** @addtogroup STM32F0xx_System_Includes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+
+/** @addtogroup STM32F0xx_System_Exported_types
+  * @{
+  */
+  /* This variable is updated in three ways:
+      1) by calling CMSIS function SystemCoreClockUpdate()
+      3) by calling HAL API function HAL_RCC_GetHCLKFreq()
+      3) by calling HAL API function HAL_RCC_ClockConfig()
+         Note: If you use this function to configure the system clock; then there
+               is no need to call the 2 first functions listed above, since SystemCoreClock
+               variable is updated automatically.
+  */
+extern uint32_t SystemCoreClock;          /*!< System Clock Frequency (Core Clock) */
+extern const uint8_t AHBPrescTable[16];   /*!< AHB prescalers table values */
+extern const uint8_t APBPrescTable[8];    /*!< APB prescalers table values */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F0xx_System_Exported_Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F0xx_System_Exported_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F0xx_System_Exported_Functions
+  * @{
+  */
+  
+extern void SystemInit(void);
+extern void SystemCoreClockUpdate(void);
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /*__SYSTEM_STM32F0XX_H */
+
+/**
+  * @}
+  */
+  
+/**
+  * @}
+  */  
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/CMSIS/Include/cmsis_armcc.h

@@ -0,0 +1,865 @@
+/**************************************************************************//**
+ * @file     cmsis_armcc.h
+ * @brief    CMSIS compiler ARMCC (Arm Compiler 5) header file
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_ARMCC_H
+#define __CMSIS_ARMCC_H
+
+
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 400677)
+  #error "Please use Arm Compiler Toolchain V4.0.677 or later!"
+#endif
+
+/* CMSIS compiler control architecture macros */
+#if ((defined (__TARGET_ARCH_6_M  ) && (__TARGET_ARCH_6_M   == 1)) || \
+     (defined (__TARGET_ARCH_6S_M ) && (__TARGET_ARCH_6S_M  == 1))   )
+  #define __ARM_ARCH_6M__           1
+#endif
+
+#if (defined (__TARGET_ARCH_7_M ) && (__TARGET_ARCH_7_M  == 1))
+  #define __ARM_ARCH_7M__           1
+#endif
+
+#if (defined (__TARGET_ARCH_7E_M) && (__TARGET_ARCH_7E_M == 1))
+  #define __ARM_ARCH_7EM__          1
+#endif
+
+  /* __ARM_ARCH_8M_BASE__  not applicable */
+  /* __ARM_ARCH_8M_MAIN__  not applicable */
+
+
+/* CMSIS compiler specific defines */
+#ifndef   __ASM
+  #define __ASM                                  __asm
+#endif
+#ifndef   __INLINE
+  #define __INLINE                               __inline
+#endif
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE                        static __inline
+#endif
+#ifndef   __STATIC_FORCEINLINE                 
+  #define __STATIC_FORCEINLINE                   static __forceinline
+#endif           
+#ifndef   __NO_RETURN
+  #define __NO_RETURN                            __declspec(noreturn)
+#endif
+#ifndef   __USED
+  #define __USED                                 __attribute__((used))
+#endif
+#ifndef   __WEAK
+  #define __WEAK                                 __attribute__((weak))
+#endif
+#ifndef   __PACKED
+  #define __PACKED                               __attribute__((packed))
+#endif
+#ifndef   __PACKED_STRUCT
+  #define __PACKED_STRUCT                        __packed struct
+#endif
+#ifndef   __PACKED_UNION
+  #define __PACKED_UNION                         __packed union
+#endif
+#ifndef   __UNALIGNED_UINT32        /* deprecated */
+  #define __UNALIGNED_UINT32(x)                  (*((__packed uint32_t *)(x)))
+#endif
+#ifndef   __UNALIGNED_UINT16_WRITE
+  #define __UNALIGNED_UINT16_WRITE(addr, val)    ((*((__packed uint16_t *)(addr))) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT16_READ
+  #define __UNALIGNED_UINT16_READ(addr)          (*((const __packed uint16_t *)(addr)))
+#endif
+#ifndef   __UNALIGNED_UINT32_WRITE
+  #define __UNALIGNED_UINT32_WRITE(addr, val)    ((*((__packed uint32_t *)(addr))) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT32_READ
+  #define __UNALIGNED_UINT32_READ(addr)          (*((const __packed uint32_t *)(addr)))
+#endif
+#ifndef   __ALIGNED
+  #define __ALIGNED(x)                           __attribute__((aligned(x)))
+#endif
+#ifndef   __RESTRICT
+  #define __RESTRICT                             __restrict
+#endif
+
+/* ###########################  Core Function Access  ########################### */
+/** \ingroup  CMSIS_Core_FunctionInterface
+    \defgroup CMSIS_Core_RegAccFunctions CMSIS Core Register Access Functions
+  @{
+ */
+
+/**
+  \brief   Enable IRQ Interrupts
+  \details Enables IRQ interrupts by clearing the I-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+/* intrinsic void __enable_irq();     */
+
+
+/**
+  \brief   Disable IRQ Interrupts
+  \details Disables IRQ interrupts by setting the I-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+/* intrinsic void __disable_irq();    */
+
+/**
+  \brief   Get Control Register
+  \details Returns the content of the Control Register.
+  \return               Control Register value
+ */
+__STATIC_INLINE uint32_t __get_CONTROL(void)
+{
+  register uint32_t __regControl         __ASM("control");
+  return(__regControl);
+}
+
+
+/**
+  \brief   Set Control Register
+  \details Writes the given value to the Control Register.
+  \param [in]    control  Control Register value to set
+ */
+__STATIC_INLINE void __set_CONTROL(uint32_t control)
+{
+  register uint32_t __regControl         __ASM("control");
+  __regControl = control;
+}
+
+
+/**
+  \brief   Get IPSR Register
+  \details Returns the content of the IPSR Register.
+  \return               IPSR Register value
+ */
+__STATIC_INLINE uint32_t __get_IPSR(void)
+{
+  register uint32_t __regIPSR          __ASM("ipsr");
+  return(__regIPSR);
+}
+
+
+/**
+  \brief   Get APSR Register
+  \details Returns the content of the APSR Register.
+  \return               APSR Register value
+ */
+__STATIC_INLINE uint32_t __get_APSR(void)
+{
+  register uint32_t __regAPSR          __ASM("apsr");
+  return(__regAPSR);
+}
+
+
+/**
+  \brief   Get xPSR Register
+  \details Returns the content of the xPSR Register.
+  \return               xPSR Register value
+ */
+__STATIC_INLINE uint32_t __get_xPSR(void)
+{
+  register uint32_t __regXPSR          __ASM("xpsr");
+  return(__regXPSR);
+}
+
+
+/**
+  \brief   Get Process Stack Pointer
+  \details Returns the current value of the Process Stack Pointer (PSP).
+  \return               PSP Register value
+ */
+__STATIC_INLINE uint32_t __get_PSP(void)
+{
+  register uint32_t __regProcessStackPointer  __ASM("psp");
+  return(__regProcessStackPointer);
+}
+
+
+/**
+  \brief   Set Process Stack Pointer
+  \details Assigns the given value to the Process Stack Pointer (PSP).
+  \param [in]    topOfProcStack  Process Stack Pointer value to set
+ */
+__STATIC_INLINE void __set_PSP(uint32_t topOfProcStack)
+{
+  register uint32_t __regProcessStackPointer  __ASM("psp");
+  __regProcessStackPointer = topOfProcStack;
+}
+
+
+/**
+  \brief   Get Main Stack Pointer
+  \details Returns the current value of the Main Stack Pointer (MSP).
+  \return               MSP Register value
+ */
+__STATIC_INLINE uint32_t __get_MSP(void)
+{
+  register uint32_t __regMainStackPointer     __ASM("msp");
+  return(__regMainStackPointer);
+}
+
+
+/**
+  \brief   Set Main Stack Pointer
+  \details Assigns the given value to the Main Stack Pointer (MSP).
+  \param [in]    topOfMainStack  Main Stack Pointer value to set
+ */
+__STATIC_INLINE void __set_MSP(uint32_t topOfMainStack)
+{
+  register uint32_t __regMainStackPointer     __ASM("msp");
+  __regMainStackPointer = topOfMainStack;
+}
+
+
+/**
+  \brief   Get Priority Mask
+  \details Returns the current state of the priority mask bit from the Priority Mask Register.
+  \return               Priority Mask value
+ */
+__STATIC_INLINE uint32_t __get_PRIMASK(void)
+{
+  register uint32_t __regPriMask         __ASM("primask");
+  return(__regPriMask);
+}
+
+
+/**
+  \brief   Set Priority Mask
+  \details Assigns the given value to the Priority Mask Register.
+  \param [in]    priMask  Priority Mask
+ */
+__STATIC_INLINE void __set_PRIMASK(uint32_t priMask)
+{
+  register uint32_t __regPriMask         __ASM("primask");
+  __regPriMask = (priMask);
+}
+
+
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+/**
+  \brief   Enable FIQ
+  \details Enables FIQ interrupts by clearing the F-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+#define __enable_fault_irq                __enable_fiq
+
+
+/**
+  \brief   Disable FIQ
+  \details Disables FIQ interrupts by setting the F-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+#define __disable_fault_irq               __disable_fiq
+
+
+/**
+  \brief   Get Base Priority
+  \details Returns the current value of the Base Priority register.
+  \return               Base Priority register value
+ */
+__STATIC_INLINE uint32_t  __get_BASEPRI(void)
+{
+  register uint32_t __regBasePri         __ASM("basepri");
+  return(__regBasePri);
+}
+
+
+/**
+  \brief   Set Base Priority
+  \details Assigns the given value to the Base Priority register.
+  \param [in]    basePri  Base Priority value to set
+ */
+__STATIC_INLINE void __set_BASEPRI(uint32_t basePri)
+{
+  register uint32_t __regBasePri         __ASM("basepri");
+  __regBasePri = (basePri & 0xFFU);
+}
+
+
+/**
+  \brief   Set Base Priority with condition
+  \details Assigns the given value to the Base Priority register only if BASEPRI masking is disabled,
+           or the new value increases the BASEPRI priority level.
+  \param [in]    basePri  Base Priority value to set
+ */
+__STATIC_INLINE void __set_BASEPRI_MAX(uint32_t basePri)
+{
+  register uint32_t __regBasePriMax      __ASM("basepri_max");
+  __regBasePriMax = (basePri & 0xFFU);
+}
+
+
+/**
+  \brief   Get Fault Mask
+  \details Returns the current value of the Fault Mask register.
+  \return               Fault Mask register value
+ */
+__STATIC_INLINE uint32_t __get_FAULTMASK(void)
+{
+  register uint32_t __regFaultMask       __ASM("faultmask");
+  return(__regFaultMask);
+}
+
+
+/**
+  \brief   Set Fault Mask
+  \details Assigns the given value to the Fault Mask register.
+  \param [in]    faultMask  Fault Mask value to set
+ */
+__STATIC_INLINE void __set_FAULTMASK(uint32_t faultMask)
+{
+  register uint32_t __regFaultMask       __ASM("faultmask");
+  __regFaultMask = (faultMask & (uint32_t)1U);
+}
+
+#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+
+/**
+  \brief   Get FPSCR
+  \details Returns the current value of the Floating Point Status/Control register.
+  \return               Floating Point Status/Control register value
+ */
+__STATIC_INLINE uint32_t __get_FPSCR(void)
+{
+#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+     (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  register uint32_t __regfpscr         __ASM("fpscr");
+  return(__regfpscr);
+#else
+   return(0U);
+#endif
+}
+
+
+/**
+  \brief   Set FPSCR
+  \details Assigns the given value to the Floating Point Status/Control register.
+  \param [in]    fpscr  Floating Point Status/Control value to set
+ */
+__STATIC_INLINE void __set_FPSCR(uint32_t fpscr)
+{
+#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+     (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  register uint32_t __regfpscr         __ASM("fpscr");
+  __regfpscr = (fpscr);
+#else
+  (void)fpscr;
+#endif
+}
+
+
+/*@} end of CMSIS_Core_RegAccFunctions */
+
+
+/* ##########################  Core Instruction Access  ######################### */
+/** \defgroup CMSIS_Core_InstructionInterface CMSIS Core Instruction Interface
+  Access to dedicated instructions
+  @{
+*/
+
+/**
+  \brief   No Operation
+  \details No Operation does nothing. This instruction can be used for code alignment purposes.
+ */
+#define __NOP                             __nop
+
+
+/**
+  \brief   Wait For Interrupt
+  \details Wait For Interrupt is a hint instruction that suspends execution until one of a number of events occurs.
+ */
+#define __WFI                             __wfi
+
+
+/**
+  \brief   Wait For Event
+  \details Wait For Event is a hint instruction that permits the processor to enter
+           a low-power state until one of a number of events occurs.
+ */
+#define __WFE                             __wfe
+
+
+/**
+  \brief   Send Event
+  \details Send Event is a hint instruction. It causes an event to be signaled to the CPU.
+ */
+#define __SEV                             __sev
+
+
+/**
+  \brief   Instruction Synchronization Barrier
+  \details Instruction Synchronization Barrier flushes the pipeline in the processor,
+           so that all instructions following the ISB are fetched from cache or memory,
+           after the instruction has been completed.
+ */
+#define __ISB() do {\
+                   __schedule_barrier();\
+                   __isb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Synchronization Barrier
+  \details Acts as a special kind of Data Memory Barrier.
+           It completes when all explicit memory accesses before this instruction complete.
+ */
+#define __DSB() do {\
+                   __schedule_barrier();\
+                   __dsb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Memory Barrier
+  \details Ensures the apparent order of the explicit memory operations before
+           and after the instruction, without ensuring their completion.
+ */
+#define __DMB() do {\
+                   __schedule_barrier();\
+                   __dmb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+                  
+/**
+  \brief   Reverse byte order (32 bit)
+  \details Reverses the byte order in unsigned integer value. For example, 0x12345678 becomes 0x78563412.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#define __REV                             __rev
+
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order within each halfword of a word. For example, 0x12345678 becomes 0x34127856.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".rev16_text"))) __STATIC_INLINE __ASM uint32_t __REV16(uint32_t value)
+{
+  rev16 r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order in a 16-bit value and returns the signed 16-bit result. For example, 0x0080 becomes 0x8000.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".revsh_text"))) __STATIC_INLINE __ASM int16_t __REVSH(int16_t value)
+{
+  revsh r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   Rotate Right in unsigned value (32 bit)
+  \details Rotate Right (immediate) provides the value of the contents of a register rotated by a variable number of bits.
+  \param [in]    op1  Value to rotate
+  \param [in]    op2  Number of Bits to rotate
+  \return               Rotated value
+ */
+#define __ROR                             __ror
+
+
+/**
+  \brief   Breakpoint
+  \details Causes the processor to enter Debug state.
+           Debug tools can use this to investigate system state when the instruction at a particular address is reached.
+  \param [in]    value  is ignored by the processor.
+                 If required, a debugger can use it to store additional information about the breakpoint.
+ */
+#define __BKPT(value)                       __breakpoint(value)
+
+
+/**
+  \brief   Reverse bit order of value
+  \details Reverses the bit order of the given value.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+  #define __RBIT                          __rbit
+#else
+__attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value)
+{
+  uint32_t result;
+  uint32_t s = (4U /*sizeof(v)*/ * 8U) - 1U; /* extra shift needed at end */
+
+  result = value;                      /* r will be reversed bits of v; first get LSB of v */
+  for (value >>= 1U; value != 0U; value >>= 1U)
+  {
+    result <<= 1U;
+    result |= value & 1U;
+    s--;
+  }
+  result <<= s;                        /* shift when v's highest bits are zero */
+  return result;
+}
+#endif
+
+
+/**
+  \brief   Count leading zeros
+  \details Counts the number of leading zeros of a data value.
+  \param [in]  value  Value to count the leading zeros
+  \return             number of leading zeros in value
+ */
+#define __CLZ                             __clz
+
+
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+/**
+  \brief   LDR Exclusive (8 bit)
+  \details Executes a exclusive LDR instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXB(ptr)                                                        ((uint8_t ) __ldrex(ptr))
+#else
+  #define __LDREXB(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint8_t ) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   LDR Exclusive (16 bit)
+  \details Executes a exclusive LDR instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXH(ptr)                                                        ((uint16_t) __ldrex(ptr))
+#else
+  #define __LDREXH(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint16_t) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   LDR Exclusive (32 bit)
+  \details Executes a exclusive LDR instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXW(ptr)                                                        ((uint32_t ) __ldrex(ptr))
+#else
+  #define __LDREXW(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint32_t ) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (8 bit)
+  \details Executes a exclusive STR instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXB(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXB(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (16 bit)
+  \details Executes a exclusive STR instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXH(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXH(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (32 bit)
+  \details Executes a exclusive STR instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXW(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXW(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   Remove the exclusive lock
+  \details Removes the exclusive lock which is created by LDREX.
+ */
+#define __CLREX                           __clrex
+
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+#define __SSAT                            __ssat
+
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+#define __USAT                            __usat
+
+
+/**
+  \brief   Rotate Right with Extend (32 bit)
+  \details Moves each bit of a bitstring right by one bit.
+           The carry input is shifted in at the left end of the bitstring.
+  \param [in]    value  Value to rotate
+  \return               Rotated value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".rrx_text"))) __STATIC_INLINE __ASM uint32_t __RRX(uint32_t value)
+{
+  rrx r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   LDRT Unprivileged (8 bit)
+  \details Executes a Unprivileged LDRT instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+#define __LDRBT(ptr)                      ((uint8_t )  __ldrt(ptr))
+
+
+/**
+  \brief   LDRT Unprivileged (16 bit)
+  \details Executes a Unprivileged LDRT instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+#define __LDRHT(ptr)                      ((uint16_t)  __ldrt(ptr))
+
+
+/**
+  \brief   LDRT Unprivileged (32 bit)
+  \details Executes a Unprivileged LDRT instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+#define __LDRT(ptr)                       ((uint32_t ) __ldrt(ptr))
+
+
+/**
+  \brief   STRT Unprivileged (8 bit)
+  \details Executes a Unprivileged STRT instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRBT(value, ptr)               __strt(value, ptr)
+
+
+/**
+  \brief   STRT Unprivileged (16 bit)
+  \details Executes a Unprivileged STRT instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRHT(value, ptr)               __strt(value, ptr)
+
+
+/**
+  \brief   STRT Unprivileged (32 bit)
+  \details Executes a Unprivileged STRT instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRT(value, ptr)                __strt(value, ptr)
+
+#else  /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+__attribute__((always_inline)) __STATIC_INLINE int32_t __SSAT(int32_t val, uint32_t sat)
+{
+  if ((sat >= 1U) && (sat <= 32U))
+  {
+    const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U);
+    const int32_t min = -1 - max ;
+    if (val > max)
+    {
+      return max;
+    }
+    else if (val < min)
+    {
+      return min;
+    }
+  }
+  return val;
+}
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+__attribute__((always_inline)) __STATIC_INLINE uint32_t __USAT(int32_t val, uint32_t sat)
+{
+  if (sat <= 31U)
+  {
+    const uint32_t max = ((1U << sat) - 1U);
+    if (val > (int32_t)max)
+    {
+      return max;
+    }
+    else if (val < 0)
+    {
+      return 0U;
+    }
+  }
+  return (uint32_t)val;
+}
+
+#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+/*@}*/ /* end of group CMSIS_Core_InstructionInterface */
+
+
+/* ###################  Compiler specific Intrinsics  ########################### */
+/** \defgroup CMSIS_SIMD_intrinsics CMSIS SIMD Intrinsics
+  Access to dedicated SIMD instructions
+  @{
+*/
+
+#if ((defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+#define __SADD8                           __sadd8
+#define __QADD8                           __qadd8
+#define __SHADD8                          __shadd8
+#define __UADD8                           __uadd8
+#define __UQADD8                          __uqadd8
+#define __UHADD8                          __uhadd8
+#define __SSUB8                           __ssub8
+#define __QSUB8                           __qsub8
+#define __SHSUB8                          __shsub8
+#define __USUB8                           __usub8
+#define __UQSUB8                          __uqsub8
+#define __UHSUB8                          __uhsub8
+#define __SADD16                          __sadd16
+#define __QADD16                          __qadd16
+#define __SHADD16                         __shadd16
+#define __UADD16                          __uadd16
+#define __UQADD16                         __uqadd16
+#define __UHADD16                         __uhadd16
+#define __SSUB16                          __ssub16
+#define __QSUB16                          __qsub16
+#define __SHSUB16                         __shsub16
+#define __USUB16                          __usub16
+#define __UQSUB16                         __uqsub16
+#define __UHSUB16                         __uhsub16
+#define __SASX                            __sasx
+#define __QASX                            __qasx
+#define __SHASX                           __shasx
+#define __UASX                            __uasx
+#define __UQASX                           __uqasx
+#define __UHASX                           __uhasx
+#define __SSAX                            __ssax
+#define __QSAX                            __qsax
+#define __SHSAX                           __shsax
+#define __USAX                            __usax
+#define __UQSAX                           __uqsax
+#define __UHSAX                           __uhsax
+#define __USAD8                           __usad8
+#define __USADA8                          __usada8
+#define __SSAT16                          __ssat16
+#define __USAT16                          __usat16
+#define __UXTB16                          __uxtb16
+#define __UXTAB16                         __uxtab16
+#define __SXTB16                          __sxtb16
+#define __SXTAB16                         __sxtab16
+#define __SMUAD                           __smuad
+#define __SMUADX                          __smuadx
+#define __SMLAD                           __smlad
+#define __SMLADX                          __smladx
+#define __SMLALD                          __smlald
+#define __SMLALDX                         __smlaldx
+#define __SMUSD                           __smusd
+#define __SMUSDX                          __smusdx
+#define __SMLSD                           __smlsd
+#define __SMLSDX                          __smlsdx
+#define __SMLSLD                          __smlsld
+#define __SMLSLDX                         __smlsldx
+#define __SEL                             __sel
+#define __QADD                            __qadd
+#define __QSUB                            __qsub
+
+#define __PKHBT(ARG1,ARG2,ARG3)          ( ((((uint32_t)(ARG1))          ) & 0x0000FFFFUL) |  \
+                                           ((((uint32_t)(ARG2)) << (ARG3)) & 0xFFFF0000UL)  )
+
+#define __PKHTB(ARG1,ARG2,ARG3)          ( ((((uint32_t)(ARG1))          ) & 0xFFFF0000UL) |  \
+                                           ((((uint32_t)(ARG2)) >> (ARG3)) & 0x0000FFFFUL)  )
+
+#define __SMMLA(ARG1,ARG2,ARG3)          ( (int32_t)((((int64_t)(ARG1) * (ARG2)) + \
+                                                      ((int64_t)(ARG3) << 32U)     ) >> 32U))
+
+#endif /* ((defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+/*@} end of group CMSIS_SIMD_intrinsics */
+
+
+#endif /* __CMSIS_ARMCC_H */

LED/Drivers/CMSIS/Include/cmsis_compiler.h

@@ -0,0 +1,266 @@
+/**************************************************************************//**
+ * @file     cmsis_compiler.h
+ * @brief    CMSIS compiler generic header file
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_COMPILER_H
+#define __CMSIS_COMPILER_H
+
+#include <stdint.h>
+
+/*
+ * Arm Compiler 4/5
+ */
+#if   defined ( __CC_ARM )
+  #include "cmsis_armcc.h"
+
+
+/*
+ * Arm Compiler 6 (armclang)
+ */
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #include "cmsis_armclang.h"
+
+
+/*
+ * GNU Compiler
+ */
+#elif defined ( __GNUC__ )
+  #include "cmsis_gcc.h"
+
+
+/*
+ * IAR Compiler
+ */
+#elif defined ( __ICCARM__ )
+  #include <cmsis_iccarm.h>
+
+
+/*
+ * TI Arm Compiler
+ */
+#elif defined ( __TI_ARM__ )
+  #include <cmsis_ccs.h>
+
+  #ifndef   __ASM
+    #define __ASM                                  __asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    #define __NO_RETURN                            __attribute__((noreturn))
+  #endif
+  #ifndef   __USED
+    #define __USED                                 __attribute__((used))
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __attribute__((weak))
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               __attribute__((packed))
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        struct __attribute__((packed))
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         union __attribute__((packed))
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    struct __attribute__((packed)) T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void*)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #define __ALIGNED(x)                           __attribute__((aligned(x)))
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+/*
+ * TASKING Compiler
+ */
+#elif defined ( __TASKING__ )
+  /*
+   * The CMSIS functions have been implemented as intrinsics in the compiler.
+   * Please use "carm -?i" to get an up to date list of all intrinsics,
+   * Including the CMSIS ones.
+   */
+
+  #ifndef   __ASM
+    #define __ASM                                  __asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    #define __NO_RETURN                            __attribute__((noreturn))
+  #endif
+  #ifndef   __USED
+    #define __USED                                 __attribute__((used))
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __attribute__((weak))
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               __packed__
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        struct __packed__
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         union __packed__
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    struct __packed__ T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #define __ALIGNED(x)              __align(x)
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+/*
+ * COSMIC Compiler
+ */
+#elif defined ( __CSMC__ )
+   #include <cmsis_csm.h>
+
+ #ifndef   __ASM
+    #define __ASM                                  _asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    // NO RETURN is automatically detected hence no warning here
+    #define __NO_RETURN
+  #endif
+  #ifndef   __USED
+    #warning No compiler specific solution for __USED. __USED is ignored.
+    #define __USED
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __weak
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               @packed
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        @packed struct
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         @packed union
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    @packed struct T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #warning No compiler specific solution for __ALIGNED. __ALIGNED is ignored.
+    #define __ALIGNED(x)
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+#else
+  #error Unknown compiler.
+#endif
+
+
+#endif /* __CMSIS_COMPILER_H */
+

LED/Drivers/CMSIS/Include/cmsis_iccarm.h

@@ -0,0 +1,935 @@
+/**************************************************************************//**
+ * @file     cmsis_iccarm.h
+ * @brief    CMSIS compiler ICCARM (IAR Compiler for Arm) header file
+ * @version  V5.0.7
+ * @date     19. June 2018
+ ******************************************************************************/
+
+//------------------------------------------------------------------------------
+//
+// Copyright (c) 2017-2018 IAR Systems
+//
+// Licensed under the Apache License, Version 2.0 (the "License")
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//     http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+//
+//------------------------------------------------------------------------------
+
+
+#ifndef __CMSIS_ICCARM_H__
+#define __CMSIS_ICCARM_H__
+
+#ifndef __ICCARM__
+  #error This file should only be compiled by ICCARM
+#endif
+
+#pragma system_include
+
+#define __IAR_FT _Pragma("inline=forced") __intrinsic
+
+#if (__VER__ >= 8000000)
+  #define __ICCARM_V8 1
+#else
+  #define __ICCARM_V8 0
+#endif
+
+#ifndef __ALIGNED
+  #if __ICCARM_V8
+    #define __ALIGNED(x) __attribute__((aligned(x)))
+  #elif (__VER__ >= 7080000)
+    /* Needs IAR language extensions */
+    #define __ALIGNED(x) __attribute__((aligned(x)))
+  #else
+    #warning No compiler specific solution for __ALIGNED.__ALIGNED is ignored.
+    #define __ALIGNED(x)
+  #endif
+#endif
+
+
+/* Define compiler macros for CPU architecture, used in CMSIS 5.
+ */
+#if __ARM_ARCH_6M__ || __ARM_ARCH_7M__ || __ARM_ARCH_7EM__ || __ARM_ARCH_8M_BASE__ || __ARM_ARCH_8M_MAIN__
+/* Macros already defined */
+#else
+  #if defined(__ARM8M_MAINLINE__) || defined(__ARM8EM_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #elif defined(__ARM8M_BASELINE__)
+    #define __ARM_ARCH_8M_BASE__ 1
+  #elif defined(__ARM_ARCH_PROFILE) && __ARM_ARCH_PROFILE == 'M'
+    #if __ARM_ARCH == 6
+      #define __ARM_ARCH_6M__ 1
+    #elif __ARM_ARCH == 7
+      #if __ARM_FEATURE_DSP
+        #define __ARM_ARCH_7EM__ 1
+      #else
+        #define __ARM_ARCH_7M__ 1
+      #endif
+    #endif /* __ARM_ARCH */
+  #endif /* __ARM_ARCH_PROFILE == 'M' */
+#endif
+
+/* Alternativ core deduction for older ICCARM's */
+#if !defined(__ARM_ARCH_6M__) && !defined(__ARM_ARCH_7M__) && !defined(__ARM_ARCH_7EM__) && \
+    !defined(__ARM_ARCH_8M_BASE__) && !defined(__ARM_ARCH_8M_MAIN__)
+  #if defined(__ARM6M__) && (__CORE__ == __ARM6M__)
+    #define __ARM_ARCH_6M__ 1
+  #elif defined(__ARM7M__) && (__CORE__ == __ARM7M__)
+    #define __ARM_ARCH_7M__ 1
+  #elif defined(__ARM7EM__) && (__CORE__ == __ARM7EM__)
+    #define __ARM_ARCH_7EM__  1
+  #elif defined(__ARM8M_BASELINE__) && (__CORE == __ARM8M_BASELINE__)
+    #define __ARM_ARCH_8M_BASE__ 1
+  #elif defined(__ARM8M_MAINLINE__) && (__CORE == __ARM8M_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #elif defined(__ARM8EM_MAINLINE__) && (__CORE == __ARM8EM_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #else
+    #error "Unknown target."
+  #endif
+#endif
+
+
+
+#if defined(__ARM_ARCH_6M__) && __ARM_ARCH_6M__==1
+  #define __IAR_M0_FAMILY  1
+#elif defined(__ARM_ARCH_8M_BASE__) && __ARM_ARCH_8M_BASE__==1
+  #define __IAR_M0_FAMILY  1
+#else
+  #define __IAR_M0_FAMILY  0
+#endif
+
+
+#ifndef __ASM
+  #define __ASM __asm
+#endif
+
+#ifndef __INLINE
+  #define __INLINE inline
+#endif
+
+#ifndef   __NO_RETURN
+  #if __ICCARM_V8
+    #define __NO_RETURN __attribute__((__noreturn__))
+  #else
+    #define __NO_RETURN _Pragma("object_attribute=__noreturn")
+  #endif
+#endif
+
+#ifndef   __PACKED
+  #if __ICCARM_V8
+    #define __PACKED __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED __packed
+  #endif
+#endif
+
+#ifndef   __PACKED_STRUCT
+  #if __ICCARM_V8
+    #define __PACKED_STRUCT struct __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED_STRUCT __packed struct
+  #endif
+#endif
+
+#ifndef   __PACKED_UNION
+  #if __ICCARM_V8
+    #define __PACKED_UNION union __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED_UNION __packed union
+  #endif
+#endif
+
+#ifndef   __RESTRICT
+  #define __RESTRICT            __restrict
+#endif
+
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE       static inline
+#endif
+
+#ifndef   __FORCEINLINE
+  #define __FORCEINLINE         _Pragma("inline=forced")
+#endif
+
+#ifndef   __STATIC_FORCEINLINE
+  #define __STATIC_FORCEINLINE  __FORCEINLINE __STATIC_INLINE
+#endif
+
+#ifndef __UNALIGNED_UINT16_READ
+#pragma language=save
+#pragma language=extended
+__IAR_FT uint16_t __iar_uint16_read(void const *ptr)
+{
+  return *(__packed uint16_t*)(ptr);
+}
+#pragma language=restore
+#define __UNALIGNED_UINT16_READ(PTR) __iar_uint16_read(PTR)
+#endif
+
+
+#ifndef __UNALIGNED_UINT16_WRITE
+#pragma language=save
+#pragma language=extended
+__IAR_FT void __iar_uint16_write(void const *ptr, uint16_t val)
+{
+  *(__packed uint16_t*)(ptr) = val;;
+}
+#pragma language=restore
+#define __UNALIGNED_UINT16_WRITE(PTR,VAL) __iar_uint16_write(PTR,VAL)
+#endif
+
+#ifndef __UNALIGNED_UINT32_READ
+#pragma language=save
+#pragma language=extended
+__IAR_FT uint32_t __iar_uint32_read(void const *ptr)
+{
+  return *(__packed uint32_t*)(ptr);
+}
+#pragma language=restore
+#define __UNALIGNED_UINT32_READ(PTR) __iar_uint32_read(PTR)
+#endif
+
+#ifndef __UNALIGNED_UINT32_WRITE
+#pragma language=save
+#pragma language=extended
+__IAR_FT void __iar_uint32_write(void const *ptr, uint32_t val)
+{
+  *(__packed uint32_t*)(ptr) = val;;
+}
+#pragma language=restore
+#define __UNALIGNED_UINT32_WRITE(PTR,VAL) __iar_uint32_write(PTR,VAL)
+#endif
+
+#ifndef __UNALIGNED_UINT32   /* deprecated */
+#pragma language=save
+#pragma language=extended
+__packed struct  __iar_u32 { uint32_t v; };
+#pragma language=restore
+#define __UNALIGNED_UINT32(PTR) (((struct __iar_u32 *)(PTR))->v)
+#endif
+
+#ifndef   __USED
+  #if __ICCARM_V8
+    #define __USED __attribute__((used))
+  #else
+    #define __USED _Pragma("__root")
+  #endif
+#endif
+
+#ifndef   __WEAK
+  #if __ICCARM_V8
+    #define __WEAK __attribute__((weak))
+  #else
+    #define __WEAK _Pragma("__weak")
+  #endif
+#endif
+
+
+#ifndef __ICCARM_INTRINSICS_VERSION__
+  #define __ICCARM_INTRINSICS_VERSION__  0
+#endif
+
+#if __ICCARM_INTRINSICS_VERSION__ == 2
+
+  #if defined(__CLZ)
+    #undef __CLZ
+  #endif
+  #if defined(__REVSH)
+    #undef __REVSH
+  #endif
+  #if defined(__RBIT)
+    #undef __RBIT
+  #endif
+  #if defined(__SSAT)
+    #undef __SSAT
+  #endif
+  #if defined(__USAT)
+    #undef __USAT
+  #endif
+
+  #include "iccarm_builtin.h"
+
+  #define __disable_fault_irq __iar_builtin_disable_fiq
+  #define __disable_irq       __iar_builtin_disable_interrupt
+  #define __enable_fault_irq  __iar_builtin_enable_fiq
+  #define __enable_irq        __iar_builtin_enable_interrupt
+  #define __arm_rsr           __iar_builtin_rsr
+  #define __arm_wsr           __iar_builtin_wsr
+
+
+  #define __get_APSR()                (__arm_rsr("APSR"))
+  #define __get_BASEPRI()             (__arm_rsr("BASEPRI"))
+  #define __get_CONTROL()             (__arm_rsr("CONTROL"))
+  #define __get_FAULTMASK()           (__arm_rsr("FAULTMASK"))
+
+  #if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+       (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+    #define __get_FPSCR()             (__arm_rsr("FPSCR"))
+    #define __set_FPSCR(VALUE)        (__arm_wsr("FPSCR", (VALUE)))
+  #else
+    #define __get_FPSCR()             ( 0 )
+    #define __set_FPSCR(VALUE)        ((void)VALUE)
+  #endif
+
+  #define __get_IPSR()                (__arm_rsr("IPSR"))
+  #define __get_MSP()                 (__arm_rsr("MSP"))
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure MSPLIM is RAZ/WI
+    #define __get_MSPLIM()            (0U)
+  #else
+    #define __get_MSPLIM()            (__arm_rsr("MSPLIM"))
+  #endif
+  #define __get_PRIMASK()             (__arm_rsr("PRIMASK"))
+  #define __get_PSP()                 (__arm_rsr("PSP"))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __get_PSPLIM()            (0U)
+  #else
+    #define __get_PSPLIM()            (__arm_rsr("PSPLIM"))
+  #endif
+
+  #define __get_xPSR()                (__arm_rsr("xPSR"))
+
+  #define __set_BASEPRI(VALUE)        (__arm_wsr("BASEPRI", (VALUE)))
+  #define __set_BASEPRI_MAX(VALUE)    (__arm_wsr("BASEPRI_MAX", (VALUE)))
+  #define __set_CONTROL(VALUE)        (__arm_wsr("CONTROL", (VALUE)))
+  #define __set_FAULTMASK(VALUE)      (__arm_wsr("FAULTMASK", (VALUE)))
+  #define __set_MSP(VALUE)            (__arm_wsr("MSP", (VALUE)))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure MSPLIM is RAZ/WI
+    #define __set_MSPLIM(VALUE)       ((void)(VALUE))
+  #else
+    #define __set_MSPLIM(VALUE)       (__arm_wsr("MSPLIM", (VALUE)))
+  #endif
+  #define __set_PRIMASK(VALUE)        (__arm_wsr("PRIMASK", (VALUE)))
+  #define __set_PSP(VALUE)            (__arm_wsr("PSP", (VALUE)))
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __set_PSPLIM(VALUE)       ((void)(VALUE))
+  #else
+    #define __set_PSPLIM(VALUE)       (__arm_wsr("PSPLIM", (VALUE)))
+  #endif
+
+  #define __TZ_get_CONTROL_NS()       (__arm_rsr("CONTROL_NS"))
+  #define __TZ_set_CONTROL_NS(VALUE)  (__arm_wsr("CONTROL_NS", (VALUE)))
+  #define __TZ_get_PSP_NS()           (__arm_rsr("PSP_NS"))
+  #define __TZ_set_PSP_NS(VALUE)      (__arm_wsr("PSP_NS", (VALUE)))
+  #define __TZ_get_MSP_NS()           (__arm_rsr("MSP_NS"))
+  #define __TZ_set_MSP_NS(VALUE)      (__arm_wsr("MSP_NS", (VALUE)))
+  #define __TZ_get_SP_NS()            (__arm_rsr("SP_NS"))
+  #define __TZ_set_SP_NS(VALUE)       (__arm_wsr("SP_NS", (VALUE)))
+  #define __TZ_get_PRIMASK_NS()       (__arm_rsr("PRIMASK_NS"))
+  #define __TZ_set_PRIMASK_NS(VALUE)  (__arm_wsr("PRIMASK_NS", (VALUE)))
+  #define __TZ_get_BASEPRI_NS()       (__arm_rsr("BASEPRI_NS"))
+  #define __TZ_set_BASEPRI_NS(VALUE)  (__arm_wsr("BASEPRI_NS", (VALUE)))
+  #define __TZ_get_FAULTMASK_NS()     (__arm_rsr("FAULTMASK_NS"))
+  #define __TZ_set_FAULTMASK_NS(VALUE)(__arm_wsr("FAULTMASK_NS", (VALUE)))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __TZ_get_PSPLIM_NS()      (0U)
+    #define __TZ_set_PSPLIM_NS(VALUE) ((void)(VALUE))
+  #else
+    #define __TZ_get_PSPLIM_NS()      (__arm_rsr("PSPLIM_NS"))
+    #define __TZ_set_PSPLIM_NS(VALUE) (__arm_wsr("PSPLIM_NS", (VALUE)))
+  #endif
+
+  #define __TZ_get_MSPLIM_NS()        (__arm_rsr("MSPLIM_NS"))
+  #define __TZ_set_MSPLIM_NS(VALUE)   (__arm_wsr("MSPLIM_NS", (VALUE)))
+
+  #define __NOP     __iar_builtin_no_operation
+
+  #define __CLZ     __iar_builtin_CLZ
+  #define __CLREX   __iar_builtin_CLREX
+
+  #define __DMB     __iar_builtin_DMB
+  #define __DSB     __iar_builtin_DSB
+  #define __ISB     __iar_builtin_ISB
+
+  #define __LDREXB  __iar_builtin_LDREXB
+  #define __LDREXH  __iar_builtin_LDREXH
+  #define __LDREXW  __iar_builtin_LDREX
+
+  #define __RBIT    __iar_builtin_RBIT
+  #define __REV     __iar_builtin_REV
+  #define __REV16   __iar_builtin_REV16
+
+  __IAR_FT int16_t __REVSH(int16_t val)
+  {
+    return (int16_t) __iar_builtin_REVSH(val);
+  }
+
+  #define __ROR     __iar_builtin_ROR
+  #define __RRX     __iar_builtin_RRX
+
+  #define __SEV     __iar_builtin_SEV
+
+  #if !__IAR_M0_FAMILY
+    #define __SSAT    __iar_builtin_SSAT
+  #endif
+
+  #define __STREXB  __iar_builtin_STREXB
+  #define __STREXH  __iar_builtin_STREXH
+  #define __STREXW  __iar_builtin_STREX
+
+  #if !__IAR_M0_FAMILY
+    #define __USAT    __iar_builtin_USAT
+  #endif
+
+  #define __WFE     __iar_builtin_WFE
+  #define __WFI     __iar_builtin_WFI
+
+  #if __ARM_MEDIA__
+    #define __SADD8   __iar_builtin_SADD8
+    #define __QADD8   __iar_builtin_QADD8
+    #define __SHADD8  __iar_builtin_SHADD8
+    #define __UADD8   __iar_builtin_UADD8
+    #define __UQADD8  __iar_builtin_UQADD8
+    #define __UHADD8  __iar_builtin_UHADD8
+    #define __SSUB8   __iar_builtin_SSUB8
+    #define __QSUB8   __iar_builtin_QSUB8
+    #define __SHSUB8  __iar_builtin_SHSUB8
+    #define __USUB8   __iar_builtin_USUB8
+    #define __UQSUB8  __iar_builtin_UQSUB8
+    #define __UHSUB8  __iar_builtin_UHSUB8
+    #define __SADD16  __iar_builtin_SADD16
+    #define __QADD16  __iar_builtin_QADD16
+    #define __SHADD16 __iar_builtin_SHADD16
+    #define __UADD16  __iar_builtin_UADD16
+    #define __UQADD16 __iar_builtin_UQADD16
+    #define __UHADD16 __iar_builtin_UHADD16
+    #define __SSUB16  __iar_builtin_SSUB16
+    #define __QSUB16  __iar_builtin_QSUB16
+    #define __SHSUB16 __iar_builtin_SHSUB16
+    #define __USUB16  __iar_builtin_USUB16
+    #define __UQSUB16 __iar_builtin_UQSUB16
+    #define __UHSUB16 __iar_builtin_UHSUB16
+    #define __SASX    __iar_builtin_SASX
+    #define __QASX    __iar_builtin_QASX
+    #define __SHASX   __iar_builtin_SHASX
+    #define __UASX    __iar_builtin_UASX
+    #define __UQASX   __iar_builtin_UQASX
+    #define __UHASX   __iar_builtin_UHASX
+    #define __SSAX    __iar_builtin_SSAX
+    #define __QSAX    __iar_builtin_QSAX
+    #define __SHSAX   __iar_builtin_SHSAX
+    #define __USAX    __iar_builtin_USAX
+    #define __UQSAX   __iar_builtin_UQSAX
+    #define __UHSAX   __iar_builtin_UHSAX
+    #define __USAD8   __iar_builtin_USAD8
+    #define __USADA8  __iar_builtin_USADA8
+    #define __SSAT16  __iar_builtin_SSAT16
+    #define __USAT16  __iar_builtin_USAT16
+    #define __UXTB16  __iar_builtin_UXTB16
+    #define __UXTAB16 __iar_builtin_UXTAB16
+    #define __SXTB16  __iar_builtin_SXTB16
+    #define __SXTAB16 __iar_builtin_SXTAB16
+    #define __SMUAD   __iar_builtin_SMUAD
+    #define __SMUADX  __iar_builtin_SMUADX
+    #define __SMMLA   __iar_builtin_SMMLA
+    #define __SMLAD   __iar_builtin_SMLAD
+    #define __SMLADX  __iar_builtin_SMLADX
+    #define __SMLALD  __iar_builtin_SMLALD
+    #define __SMLALDX __iar_builtin_SMLALDX
+    #define __SMUSD   __iar_builtin_SMUSD
+    #define __SMUSDX  __iar_builtin_SMUSDX
+    #define __SMLSD   __iar_builtin_SMLSD
+    #define __SMLSDX  __iar_builtin_SMLSDX
+    #define __SMLSLD  __iar_builtin_SMLSLD
+    #define __SMLSLDX __iar_builtin_SMLSLDX
+    #define __SEL     __iar_builtin_SEL
+    #define __QADD    __iar_builtin_QADD
+    #define __QSUB    __iar_builtin_QSUB
+    #define __PKHBT   __iar_builtin_PKHBT
+    #define __PKHTB   __iar_builtin_PKHTB
+  #endif
+
+#else /* __ICCARM_INTRINSICS_VERSION__ == 2 */
+
+  #if __IAR_M0_FAMILY
+   /* Avoid clash between intrinsics.h and arm_math.h when compiling for Cortex-M0. */
+    #define __CLZ  __cmsis_iar_clz_not_active
+    #define __SSAT __cmsis_iar_ssat_not_active
+    #define __USAT __cmsis_iar_usat_not_active
+    #define __RBIT __cmsis_iar_rbit_not_active
+    #define __get_APSR  __cmsis_iar_get_APSR_not_active
+  #endif
+
+
+  #if (!((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+         (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     ))
+    #define __get_FPSCR __cmsis_iar_get_FPSR_not_active
+    #define __set_FPSCR __cmsis_iar_set_FPSR_not_active
+  #endif
+
+  #ifdef __INTRINSICS_INCLUDED
+  #error intrinsics.h is already included previously!
+  #endif
+
+  #include <intrinsics.h>
+
+  #if __IAR_M0_FAMILY
+   /* Avoid clash between intrinsics.h and arm_math.h when compiling for Cortex-M0. */
+    #undef __CLZ
+    #undef __SSAT
+    #undef __USAT
+    #undef __RBIT
+    #undef __get_APSR
+
+    __STATIC_INLINE uint8_t __CLZ(uint32_t data)
+    {
+      if (data == 0U) { return 32U; }
+
+      uint32_t count = 0U;
+      uint32_t mask = 0x80000000U;
+
+      while ((data & mask) == 0U)
+      {
+        count += 1U;
+        mask = mask >> 1U;
+      }
+      return count;
+    }
+
+    __STATIC_INLINE uint32_t __RBIT(uint32_t v)
+    {
+      uint8_t sc = 31U;
+      uint32_t r = v;
+      for (v >>= 1U; v; v >>= 1U)
+      {
+        r <<= 1U;
+        r |= v & 1U;
+        sc--;
+      }
+      return (r << sc);
+    }
+
+    __STATIC_INLINE  uint32_t __get_APSR(void)
+    {
+      uint32_t res;
+      __asm("MRS      %0,APSR" : "=r" (res));
+      return res;
+    }
+
+  #endif
+
+  #if (!((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+         (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     ))
+    #undef __get_FPSCR
+    #undef __set_FPSCR
+    #define __get_FPSCR()       (0)
+    #define __set_FPSCR(VALUE)  ((void)VALUE)
+  #endif
+
+  #pragma diag_suppress=Pe940
+  #pragma diag_suppress=Pe177
+
+  #define __enable_irq    __enable_interrupt
+  #define __disable_irq   __disable_interrupt
+  #define __NOP           __no_operation
+
+  #define __get_xPSR      __get_PSR
+
+  #if (!defined(__ARM_ARCH_6M__) || __ARM_ARCH_6M__==0)
+
+    __IAR_FT uint32_t __LDREXW(uint32_t volatile *ptr)
+    {
+      return __LDREX((unsigned long *)ptr);
+    }
+
+    __IAR_FT uint32_t __STREXW(uint32_t value, uint32_t volatile *ptr)
+    {
+      return __STREX(value, (unsigned long *)ptr);
+    }
+  #endif
+
+
+  /* __CORTEX_M is defined in core_cm0.h, core_cm3.h and core_cm4.h. */
+  #if (__CORTEX_M >= 0x03)
+
+    __IAR_FT uint32_t __RRX(uint32_t value)
+    {
+      uint32_t result;
+      __ASM("RRX      %0, %1" : "=r"(result) : "r" (value) : "cc");
+      return(result);
+    }
+
+    __IAR_FT void __set_BASEPRI_MAX(uint32_t value)
+    {
+      __asm volatile("MSR      BASEPRI_MAX,%0"::"r" (value));
+    }
+
+
+    #define __enable_fault_irq  __enable_fiq
+    #define __disable_fault_irq __disable_fiq
+
+
+  #endif /* (__CORTEX_M >= 0x03) */
+
+  __IAR_FT uint32_t __ROR(uint32_t op1, uint32_t op2)
+  {
+    return (op1 >> op2) | (op1 << ((sizeof(op1)*8)-op2));
+  }
+
+  #if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \
+       (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1))    )
+
+   __IAR_FT uint32_t __get_MSPLIM(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure MSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,MSPLIM" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __set_MSPLIM(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure MSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      MSPLIM,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t __get_PSPLIM(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,PSPLIM" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __set_PSPLIM(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      PSPLIM,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t __TZ_get_CONTROL_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,CONTROL_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_CONTROL_NS(uint32_t value)
+    {
+      __asm volatile("MSR      CONTROL_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PSP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,PSP_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PSP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      PSP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_MSP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,MSP_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_MSP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      MSP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_SP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,SP_NS" : "=r" (res));
+      return res;
+    }
+    __IAR_FT void   __TZ_set_SP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      SP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PRIMASK_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,PRIMASK_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PRIMASK_NS(uint32_t value)
+    {
+      __asm volatile("MSR      PRIMASK_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_BASEPRI_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,BASEPRI_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_BASEPRI_NS(uint32_t value)
+    {
+      __asm volatile("MSR      BASEPRI_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_FAULTMASK_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,FAULTMASK_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_FAULTMASK_NS(uint32_t value)
+    {
+      __asm volatile("MSR      FAULTMASK_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PSPLIM_NS(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,PSPLIM_NS" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PSPLIM_NS(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      PSPLIM_NS,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t   __TZ_get_MSPLIM_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,MSPLIM_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_MSPLIM_NS(uint32_t value)
+    {
+      __asm volatile("MSR      MSPLIM_NS,%0" :: "r" (value));
+    }
+
+  #endif /* __ARM_ARCH_8M_MAIN__ or __ARM_ARCH_8M_BASE__ */
+
+#endif   /* __ICCARM_INTRINSICS_VERSION__ == 2 */
+
+#define __BKPT(value)    __asm volatile ("BKPT     %0" : : "i"(value))
+
+#if __IAR_M0_FAMILY
+  __STATIC_INLINE int32_t __SSAT(int32_t val, uint32_t sat)
+  {
+    if ((sat >= 1U) && (sat <= 32U))
+    {
+      const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U);
+      const int32_t min = -1 - max ;
+      if (val > max)
+      {
+        return max;
+      }
+      else if (val < min)
+      {
+        return min;
+      }
+    }
+    return val;
+  }
+
+  __STATIC_INLINE uint32_t __USAT(int32_t val, uint32_t sat)
+  {
+    if (sat <= 31U)
+    {
+      const uint32_t max = ((1U << sat) - 1U);
+      if (val > (int32_t)max)
+      {
+        return max;
+      }
+      else if (val < 0)
+      {
+        return 0U;
+      }
+    }
+    return (uint32_t)val;
+  }
+#endif
+
+#if (__CORTEX_M >= 0x03)   /* __CORTEX_M is defined in core_cm0.h, core_cm3.h and core_cm4.h. */
+
+  __IAR_FT uint8_t __LDRBT(volatile uint8_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRBT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDRHT(volatile uint16_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRHT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDRT(volatile uint32_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return res;
+  }
+
+  __IAR_FT void __STRBT(uint8_t value, volatile uint8_t *addr)
+  {
+    __ASM("STRBT %1, [%0]" : : "r" (addr), "r" ((uint32_t)value) : "memory");
+  }
+
+  __IAR_FT void __STRHT(uint16_t value, volatile uint16_t *addr)
+  {
+    __ASM("STRHT %1, [%0]" : : "r" (addr), "r" ((uint32_t)value) : "memory");
+  }
+
+  __IAR_FT void __STRT(uint32_t value, volatile uint32_t *addr)
+  {
+    __ASM("STRT %1, [%0]" : : "r" (addr), "r" (value) : "memory");
+  }
+
+#endif /* (__CORTEX_M >= 0x03) */
+
+#if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \
+     (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1))    )
+
+
+  __IAR_FT uint8_t __LDAB(volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAB %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDAH(volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAH %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDA(volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDA %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return res;
+  }
+
+  __IAR_FT void __STLB(uint8_t value, volatile uint8_t *ptr)
+  {
+    __ASM volatile ("STLB %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT void __STLH(uint16_t value, volatile uint16_t *ptr)
+  {
+    __ASM volatile ("STLH %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT void __STL(uint32_t value, volatile uint32_t *ptr)
+  {
+    __ASM volatile ("STL %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT uint8_t __LDAEXB(volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEXB %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDAEXH(volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEXH %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDAEX(volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEX %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEXB(uint8_t value, volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEXB %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEXH(uint16_t value, volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEXH %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEX(uint32_t value, volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEX %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+#endif /* __ARM_ARCH_8M_MAIN__ or __ARM_ARCH_8M_BASE__ */
+
+#undef __IAR_FT
+#undef __IAR_M0_FAMILY
+#undef __ICCARM_V8
+
+#pragma diag_default=Pe940
+#pragma diag_default=Pe177
+
+#endif /* __CMSIS_ICCARM_H__ */

LED/Drivers/CMSIS/Include/cmsis_version.h

@@ -0,0 +1,39 @@
+/**************************************************************************//**
+ * @file     cmsis_version.h
+ * @brief    CMSIS Core(M) Version definitions
+ * @version  V5.0.2
+ * @date     19. April 2017
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2017 ARM Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CMSIS_VERSION_H
+#define __CMSIS_VERSION_H
+
+/*  CMSIS Version definitions */
+#define __CM_CMSIS_VERSION_MAIN  ( 5U)                                      /*!< [31:16] CMSIS Core(M) main version */
+#define __CM_CMSIS_VERSION_SUB   ( 1U)                                      /*!< [15:0]  CMSIS Core(M) sub version */
+#define __CM_CMSIS_VERSION       ((__CM_CMSIS_VERSION_MAIN << 16U) | \
+                                   __CM_CMSIS_VERSION_SUB           )       /*!< CMSIS Core(M) version number */
+#endif

LED/Drivers/CMSIS/Include/core_cm0.h

@@ -0,0 +1,949 @@
+/**************************************************************************//**
+ * @file     core_cm0.h
+ * @brief    CMSIS Cortex-M0 Core Peripheral Access Layer Header File
+ * @version  V5.0.5
+ * @date     28. May 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CORE_CM0_H_GENERIC
+#define __CORE_CM0_H_GENERIC
+
+#include <stdint.h>
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/**
+  \page CMSIS_MISRA_Exceptions  MISRA-C:2004 Compliance Exceptions
+  CMSIS violates the following MISRA-C:2004 rules:
+
+   \li Required Rule 8.5, object/function definition in header file.<br>
+     Function definitions in header files are used to allow 'inlining'.
+
+   \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.<br>
+     Unions are used for effective representation of core registers.
+
+   \li Advisory Rule 19.7, Function-like macro defined.<br>
+     Function-like macros are used to allow more efficient code.
+ */
+
+
+/*******************************************************************************
+ *                 CMSIS definitions
+ ******************************************************************************/
+/**
+  \ingroup Cortex_M0
+  @{
+ */
+
+#include "cmsis_version.h"
+ 
+/*  CMSIS CM0 definitions */
+#define __CM0_CMSIS_VERSION_MAIN  (__CM_CMSIS_VERSION_MAIN)              /*!< \deprecated [31:16] CMSIS HAL main version */
+#define __CM0_CMSIS_VERSION_SUB   (__CM_CMSIS_VERSION_SUB)               /*!< \deprecated [15:0]  CMSIS HAL sub version */
+#define __CM0_CMSIS_VERSION       ((__CM0_CMSIS_VERSION_MAIN << 16U) | \
+                                    __CM0_CMSIS_VERSION_SUB           )  /*!< \deprecated CMSIS HAL version number */
+
+#define __CORTEX_M                (0U)                                   /*!< Cortex-M Core */
+
+/** __FPU_USED indicates whether an FPU is used or not.
+    This core does not support an FPU at all
+*/
+#define __FPU_USED       0U
+
+#if defined ( __CC_ARM )
+  #if defined __TARGET_FPU_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #if defined __ARM_PCS_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __GNUC__ )
+  #if defined (__VFP_FP__) && !defined(__SOFTFP__)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __ICCARM__ )
+  #if defined __ARMVFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TI_ARM__ )
+  #if defined __TI_VFP_SUPPORT__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TASKING__ )
+  #if defined __FPU_VFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __CSMC__ )
+  #if ( __CSMC__ & 0x400U)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#endif
+
+#include "cmsis_compiler.h"               /* CMSIS compiler specific defines */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM0_H_GENERIC */
+
+#ifndef __CMSIS_GENERIC
+
+#ifndef __CORE_CM0_H_DEPENDANT
+#define __CORE_CM0_H_DEPENDANT
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* check device defines and use defaults */
+#if defined __CHECK_DEVICE_DEFINES
+  #ifndef __CM0_REV
+    #define __CM0_REV               0x0000U
+    #warning "__CM0_REV not defined in device header file; using default!"
+  #endif
+
+  #ifndef __NVIC_PRIO_BITS
+    #define __NVIC_PRIO_BITS          2U
+    #warning "__NVIC_PRIO_BITS not defined in device header file; using default!"
+  #endif
+
+  #ifndef __Vendor_SysTickConfig
+    #define __Vendor_SysTickConfig    0U
+    #warning "__Vendor_SysTickConfig not defined in device header file; using default!"
+  #endif
+#endif
+
+/* IO definitions (access restrictions to peripheral registers) */
+/**
+    \defgroup CMSIS_glob_defs CMSIS Global Defines
+
+    <strong>IO Type Qualifiers</strong> are used
+    \li to specify the access to peripheral variables.
+    \li for automatic generation of peripheral register debug information.
+*/
+#ifdef __cplusplus
+  #define   __I     volatile             /*!< Defines 'read only' permissions */
+#else
+  #define   __I     volatile const       /*!< Defines 'read only' permissions */
+#endif
+#define     __O     volatile             /*!< Defines 'write only' permissions */
+#define     __IO    volatile             /*!< Defines 'read / write' permissions */
+
+/* following defines should be used for structure members */
+#define     __IM     volatile const      /*! Defines 'read only' structure member permissions */
+#define     __OM     volatile            /*! Defines 'write only' structure member permissions */
+#define     __IOM    volatile            /*! Defines 'read / write' structure member permissions */
+
+/*@} end of group Cortex_M0 */
+
+
+
+/*******************************************************************************
+ *                 Register Abstraction
+  Core Register contain:
+  - Core Register
+  - Core NVIC Register
+  - Core SCB Register
+  - Core SysTick Register
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_core_register Defines and Type Definitions
+  \brief Type definitions and defines for Cortex-M processor based devices.
+*/
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_CORE  Status and Control Registers
+  \brief      Core Register type definitions.
+  @{
+ */
+
+/**
+  \brief  Union type to access the Application Program Status Register (APSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:28;              /*!< bit:  0..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} APSR_Type;
+
+/* APSR Register Definitions */
+#define APSR_N_Pos                         31U                                            /*!< APSR: N Position */
+#define APSR_N_Msk                         (1UL << APSR_N_Pos)                            /*!< APSR: N Mask */
+
+#define APSR_Z_Pos                         30U                                            /*!< APSR: Z Position */
+#define APSR_Z_Msk                         (1UL << APSR_Z_Pos)                            /*!< APSR: Z Mask */
+
+#define APSR_C_Pos                         29U                                            /*!< APSR: C Position */
+#define APSR_C_Msk                         (1UL << APSR_C_Pos)                            /*!< APSR: C Mask */
+
+#define APSR_V_Pos                         28U                                            /*!< APSR: V Position */
+#define APSR_V_Msk                         (1UL << APSR_V_Pos)                            /*!< APSR: V Mask */
+
+
+/**
+  \brief  Union type to access the Interrupt Program Status Register (IPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:23;              /*!< bit:  9..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} IPSR_Type;
+
+/* IPSR Register Definitions */
+#define IPSR_ISR_Pos                        0U                                            /*!< IPSR: ISR Position */
+#define IPSR_ISR_Msk                       (0x1FFUL /*<< IPSR_ISR_Pos*/)                  /*!< IPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Special-Purpose Program Status Registers (xPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:15;              /*!< bit:  9..23  Reserved */
+    uint32_t T:1;                        /*!< bit:     24  Thumb bit        (read 0) */
+    uint32_t _reserved1:3;               /*!< bit: 25..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} xPSR_Type;
+
+/* xPSR Register Definitions */
+#define xPSR_N_Pos                         31U                                            /*!< xPSR: N Position */
+#define xPSR_N_Msk                         (1UL << xPSR_N_Pos)                            /*!< xPSR: N Mask */
+
+#define xPSR_Z_Pos                         30U                                            /*!< xPSR: Z Position */
+#define xPSR_Z_Msk                         (1UL << xPSR_Z_Pos)                            /*!< xPSR: Z Mask */
+
+#define xPSR_C_Pos                         29U                                            /*!< xPSR: C Position */
+#define xPSR_C_Msk                         (1UL << xPSR_C_Pos)                            /*!< xPSR: C Mask */
+
+#define xPSR_V_Pos                         28U                                            /*!< xPSR: V Position */
+#define xPSR_V_Msk                         (1UL << xPSR_V_Pos)                            /*!< xPSR: V Mask */
+
+#define xPSR_T_Pos                         24U                                            /*!< xPSR: T Position */
+#define xPSR_T_Msk                         (1UL << xPSR_T_Pos)                            /*!< xPSR: T Mask */
+
+#define xPSR_ISR_Pos                        0U                                            /*!< xPSR: ISR Position */
+#define xPSR_ISR_Msk                       (0x1FFUL /*<< xPSR_ISR_Pos*/)                  /*!< xPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Control Registers (CONTROL).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:1;               /*!< bit:      0  Reserved */
+    uint32_t SPSEL:1;                    /*!< bit:      1  Stack to be used */
+    uint32_t _reserved1:30;              /*!< bit:  2..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} CONTROL_Type;
+
+/* CONTROL Register Definitions */
+#define CONTROL_SPSEL_Pos                   1U                                            /*!< CONTROL: SPSEL Position */
+#define CONTROL_SPSEL_Msk                  (1UL << CONTROL_SPSEL_Pos)                     /*!< CONTROL: SPSEL Mask */
+
+/*@} end of group CMSIS_CORE */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_NVIC  Nested Vectored Interrupt Controller (NVIC)
+  \brief      Type definitions for the NVIC Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the Nested Vectored Interrupt Controller (NVIC).
+ */
+typedef struct
+{
+  __IOM uint32_t ISER[1U];               /*!< Offset: 0x000 (R/W)  Interrupt Set Enable Register */
+        uint32_t RESERVED0[31U];
+  __IOM uint32_t ICER[1U];               /*!< Offset: 0x080 (R/W)  Interrupt Clear Enable Register */
+        uint32_t RSERVED1[31U];
+  __IOM uint32_t ISPR[1U];               /*!< Offset: 0x100 (R/W)  Interrupt Set Pending Register */
+        uint32_t RESERVED2[31U];
+  __IOM uint32_t ICPR[1U];               /*!< Offset: 0x180 (R/W)  Interrupt Clear Pending Register */
+        uint32_t RESERVED3[31U];
+        uint32_t RESERVED4[64U];
+  __IOM uint32_t IP[8U];                 /*!< Offset: 0x300 (R/W)  Interrupt Priority Register */
+}  NVIC_Type;
+
+/*@} end of group CMSIS_NVIC */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCB     System Control Block (SCB)
+  \brief    Type definitions for the System Control Block Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control Block (SCB).
+ */
+typedef struct
+{
+  __IM  uint32_t CPUID;                  /*!< Offset: 0x000 (R/ )  CPUID Base Register */
+  __IOM uint32_t ICSR;                   /*!< Offset: 0x004 (R/W)  Interrupt Control and State Register */
+        uint32_t RESERVED0;
+  __IOM uint32_t AIRCR;                  /*!< Offset: 0x00C (R/W)  Application Interrupt and Reset Control Register */
+  __IOM uint32_t SCR;                    /*!< Offset: 0x010 (R/W)  System Control Register */
+  __IOM uint32_t CCR;                    /*!< Offset: 0x014 (R/W)  Configuration Control Register */
+        uint32_t RESERVED1;
+  __IOM uint32_t SHP[2U];                /*!< Offset: 0x01C (R/W)  System Handlers Priority Registers. [0] is RESERVED */
+  __IOM uint32_t SHCSR;                  /*!< Offset: 0x024 (R/W)  System Handler Control and State Register */
+} SCB_Type;
+
+/* SCB CPUID Register Definitions */
+#define SCB_CPUID_IMPLEMENTER_Pos          24U                                            /*!< SCB CPUID: IMPLEMENTER Position */
+#define SCB_CPUID_IMPLEMENTER_Msk          (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos)          /*!< SCB CPUID: IMPLEMENTER Mask */
+
+#define SCB_CPUID_VARIANT_Pos              20U                                            /*!< SCB CPUID: VARIANT Position */
+#define SCB_CPUID_VARIANT_Msk              (0xFUL << SCB_CPUID_VARIANT_Pos)               /*!< SCB CPUID: VARIANT Mask */
+
+#define SCB_CPUID_ARCHITECTURE_Pos         16U                                            /*!< SCB CPUID: ARCHITECTURE Position */
+#define SCB_CPUID_ARCHITECTURE_Msk         (0xFUL << SCB_CPUID_ARCHITECTURE_Pos)          /*!< SCB CPUID: ARCHITECTURE Mask */
+
+#define SCB_CPUID_PARTNO_Pos                4U                                            /*!< SCB CPUID: PARTNO Position */
+#define SCB_CPUID_PARTNO_Msk               (0xFFFUL << SCB_CPUID_PARTNO_Pos)              /*!< SCB CPUID: PARTNO Mask */
+
+#define SCB_CPUID_REVISION_Pos              0U                                            /*!< SCB CPUID: REVISION Position */
+#define SCB_CPUID_REVISION_Msk             (0xFUL /*<< SCB_CPUID_REVISION_Pos*/)          /*!< SCB CPUID: REVISION Mask */
+
+/* SCB Interrupt Control State Register Definitions */
+#define SCB_ICSR_NMIPENDSET_Pos            31U                                            /*!< SCB ICSR: NMIPENDSET Position */
+#define SCB_ICSR_NMIPENDSET_Msk            (1UL << SCB_ICSR_NMIPENDSET_Pos)               /*!< SCB ICSR: NMIPENDSET Mask */
+
+#define SCB_ICSR_PENDSVSET_Pos             28U                                            /*!< SCB ICSR: PENDSVSET Position */
+#define SCB_ICSR_PENDSVSET_Msk             (1UL << SCB_ICSR_PENDSVSET_Pos)                /*!< SCB ICSR: PENDSVSET Mask */
+
+#define SCB_ICSR_PENDSVCLR_Pos             27U                                            /*!< SCB ICSR: PENDSVCLR Position */
+#define SCB_ICSR_PENDSVCLR_Msk             (1UL << SCB_ICSR_PENDSVCLR_Pos)                /*!< SCB ICSR: PENDSVCLR Mask */
+
+#define SCB_ICSR_PENDSTSET_Pos             26U                                            /*!< SCB ICSR: PENDSTSET Position */
+#define SCB_ICSR_PENDSTSET_Msk             (1UL << SCB_ICSR_PENDSTSET_Pos)                /*!< SCB ICSR: PENDSTSET Mask */
+
+#define SCB_ICSR_PENDSTCLR_Pos             25U                                            /*!< SCB ICSR: PENDSTCLR Position */
+#define SCB_ICSR_PENDSTCLR_Msk             (1UL << SCB_ICSR_PENDSTCLR_Pos)                /*!< SCB ICSR: PENDSTCLR Mask */
+
+#define SCB_ICSR_ISRPREEMPT_Pos            23U                                            /*!< SCB ICSR: ISRPREEMPT Position */
+#define SCB_ICSR_ISRPREEMPT_Msk            (1UL << SCB_ICSR_ISRPREEMPT_Pos)               /*!< SCB ICSR: ISRPREEMPT Mask */
+
+#define SCB_ICSR_ISRPENDING_Pos            22U                                            /*!< SCB ICSR: ISRPENDING Position */
+#define SCB_ICSR_ISRPENDING_Msk            (1UL << SCB_ICSR_ISRPENDING_Pos)               /*!< SCB ICSR: ISRPENDING Mask */
+
+#define SCB_ICSR_VECTPENDING_Pos           12U                                            /*!< SCB ICSR: VECTPENDING Position */
+#define SCB_ICSR_VECTPENDING_Msk           (0x1FFUL << SCB_ICSR_VECTPENDING_Pos)          /*!< SCB ICSR: VECTPENDING Mask */
+
+#define SCB_ICSR_VECTACTIVE_Pos             0U                                            /*!< SCB ICSR: VECTACTIVE Position */
+#define SCB_ICSR_VECTACTIVE_Msk            (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/)       /*!< SCB ICSR: VECTACTIVE Mask */
+
+/* SCB Application Interrupt and Reset Control Register Definitions */
+#define SCB_AIRCR_VECTKEY_Pos              16U                                            /*!< SCB AIRCR: VECTKEY Position */
+#define SCB_AIRCR_VECTKEY_Msk              (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos)            /*!< SCB AIRCR: VECTKEY Mask */
+
+#define SCB_AIRCR_VECTKEYSTAT_Pos          16U                                            /*!< SCB AIRCR: VECTKEYSTAT Position */
+#define SCB_AIRCR_VECTKEYSTAT_Msk          (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos)        /*!< SCB AIRCR: VECTKEYSTAT Mask */
+
+#define SCB_AIRCR_ENDIANESS_Pos            15U                                            /*!< SCB AIRCR: ENDIANESS Position */
+#define SCB_AIRCR_ENDIANESS_Msk            (1UL << SCB_AIRCR_ENDIANESS_Pos)               /*!< SCB AIRCR: ENDIANESS Mask */
+
+#define SCB_AIRCR_SYSRESETREQ_Pos           2U                                            /*!< SCB AIRCR: SYSRESETREQ Position */
+#define SCB_AIRCR_SYSRESETREQ_Msk          (1UL << SCB_AIRCR_SYSRESETREQ_Pos)             /*!< SCB AIRCR: SYSRESETREQ Mask */
+
+#define SCB_AIRCR_VECTCLRACTIVE_Pos         1U                                            /*!< SCB AIRCR: VECTCLRACTIVE Position */
+#define SCB_AIRCR_VECTCLRACTIVE_Msk        (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos)           /*!< SCB AIRCR: VECTCLRACTIVE Mask */
+
+/* SCB System Control Register Definitions */
+#define SCB_SCR_SEVONPEND_Pos               4U                                            /*!< SCB SCR: SEVONPEND Position */
+#define SCB_SCR_SEVONPEND_Msk              (1UL << SCB_SCR_SEVONPEND_Pos)                 /*!< SCB SCR: SEVONPEND Mask */
+
+#define SCB_SCR_SLEEPDEEP_Pos               2U                                            /*!< SCB SCR: SLEEPDEEP Position */
+#define SCB_SCR_SLEEPDEEP_Msk              (1UL << SCB_SCR_SLEEPDEEP_Pos)                 /*!< SCB SCR: SLEEPDEEP Mask */
+
+#define SCB_SCR_SLEEPONEXIT_Pos             1U                                            /*!< SCB SCR: SLEEPONEXIT Position */
+#define SCB_SCR_SLEEPONEXIT_Msk            (1UL << SCB_SCR_SLEEPONEXIT_Pos)               /*!< SCB SCR: SLEEPONEXIT Mask */
+
+/* SCB Configuration Control Register Definitions */
+#define SCB_CCR_STKALIGN_Pos                9U                                            /*!< SCB CCR: STKALIGN Position */
+#define SCB_CCR_STKALIGN_Msk               (1UL << SCB_CCR_STKALIGN_Pos)                  /*!< SCB CCR: STKALIGN Mask */
+
+#define SCB_CCR_UNALIGN_TRP_Pos             3U                                            /*!< SCB CCR: UNALIGN_TRP Position */
+#define SCB_CCR_UNALIGN_TRP_Msk            (1UL << SCB_CCR_UNALIGN_TRP_Pos)               /*!< SCB CCR: UNALIGN_TRP Mask */
+
+/* SCB System Handler Control and State Register Definitions */
+#define SCB_SHCSR_SVCALLPENDED_Pos         15U                                            /*!< SCB SHCSR: SVCALLPENDED Position */
+#define SCB_SHCSR_SVCALLPENDED_Msk         (1UL << SCB_SHCSR_SVCALLPENDED_Pos)            /*!< SCB SHCSR: SVCALLPENDED Mask */
+
+/*@} end of group CMSIS_SCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SysTick     System Tick Timer (SysTick)
+  \brief    Type definitions for the System Timer Registers.
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Timer (SysTick).
+ */
+typedef struct
+{
+  __IOM uint32_t CTRL;                   /*!< Offset: 0x000 (R/W)  SysTick Control and Status Register */
+  __IOM uint32_t LOAD;                   /*!< Offset: 0x004 (R/W)  SysTick Reload Value Register */
+  __IOM uint32_t VAL;                    /*!< Offset: 0x008 (R/W)  SysTick Current Value Register */
+  __IM  uint32_t CALIB;                  /*!< Offset: 0x00C (R/ )  SysTick Calibration Register */
+} SysTick_Type;
+
+/* SysTick Control / Status Register Definitions */
+#define SysTick_CTRL_COUNTFLAG_Pos         16U                                            /*!< SysTick CTRL: COUNTFLAG Position */
+#define SysTick_CTRL_COUNTFLAG_Msk         (1UL << SysTick_CTRL_COUNTFLAG_Pos)            /*!< SysTick CTRL: COUNTFLAG Mask */
+
+#define SysTick_CTRL_CLKSOURCE_Pos          2U                                            /*!< SysTick CTRL: CLKSOURCE Position */
+#define SysTick_CTRL_CLKSOURCE_Msk         (1UL << SysTick_CTRL_CLKSOURCE_Pos)            /*!< SysTick CTRL: CLKSOURCE Mask */
+
+#define SysTick_CTRL_TICKINT_Pos            1U                                            /*!< SysTick CTRL: TICKINT Position */
+#define SysTick_CTRL_TICKINT_Msk           (1UL << SysTick_CTRL_TICKINT_Pos)              /*!< SysTick CTRL: TICKINT Mask */
+
+#define SysTick_CTRL_ENABLE_Pos             0U                                            /*!< SysTick CTRL: ENABLE Position */
+#define SysTick_CTRL_ENABLE_Msk            (1UL /*<< SysTick_CTRL_ENABLE_Pos*/)           /*!< SysTick CTRL: ENABLE Mask */
+
+/* SysTick Reload Register Definitions */
+#define SysTick_LOAD_RELOAD_Pos             0U                                            /*!< SysTick LOAD: RELOAD Position */
+#define SysTick_LOAD_RELOAD_Msk            (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/)    /*!< SysTick LOAD: RELOAD Mask */
+
+/* SysTick Current Register Definitions */
+#define SysTick_VAL_CURRENT_Pos             0U                                            /*!< SysTick VAL: CURRENT Position */
+#define SysTick_VAL_CURRENT_Msk            (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/)    /*!< SysTick VAL: CURRENT Mask */
+
+/* SysTick Calibration Register Definitions */
+#define SysTick_CALIB_NOREF_Pos            31U                                            /*!< SysTick CALIB: NOREF Position */
+#define SysTick_CALIB_NOREF_Msk            (1UL << SysTick_CALIB_NOREF_Pos)               /*!< SysTick CALIB: NOREF Mask */
+
+#define SysTick_CALIB_SKEW_Pos             30U                                            /*!< SysTick CALIB: SKEW Position */
+#define SysTick_CALIB_SKEW_Msk             (1UL << SysTick_CALIB_SKEW_Pos)                /*!< SysTick CALIB: SKEW Mask */
+
+#define SysTick_CALIB_TENMS_Pos             0U                                            /*!< SysTick CALIB: TENMS Position */
+#define SysTick_CALIB_TENMS_Msk            (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/)    /*!< SysTick CALIB: TENMS Mask */
+
+/*@} end of group CMSIS_SysTick */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_CoreDebug       Core Debug Registers (CoreDebug)
+  \brief    Cortex-M0 Core Debug Registers (DCB registers, SHCSR, and DFSR) are only accessible over DAP and not via processor.
+            Therefore they are not covered by the Cortex-M0 header file.
+  @{
+ */
+/*@} end of group CMSIS_CoreDebug */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_bitfield     Core register bit field macros
+  \brief      Macros for use with bit field definitions (xxx_Pos, xxx_Msk).
+  @{
+ */
+
+/**
+  \brief   Mask and shift a bit field value for use in a register bit range.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of the bit field. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted value.
+*/
+#define _VAL2FLD(field, value)    (((uint32_t)(value) << field ## _Pos) & field ## _Msk)
+
+/**
+  \brief     Mask and shift a register value to extract a bit filed value.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of register. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted bit field value.
+*/
+#define _FLD2VAL(field, value)    (((uint32_t)(value) & field ## _Msk) >> field ## _Pos)
+
+/*@} end of group CMSIS_core_bitfield */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_base     Core Definitions
+  \brief      Definitions for base addresses, unions, and structures.
+  @{
+ */
+
+/* Memory mapping of Core Hardware */
+#define SCS_BASE            (0xE000E000UL)                            /*!< System Control Space Base Address */
+#define SysTick_BASE        (SCS_BASE +  0x0010UL)                    /*!< SysTick Base Address */
+#define NVIC_BASE           (SCS_BASE +  0x0100UL)                    /*!< NVIC Base Address */
+#define SCB_BASE            (SCS_BASE +  0x0D00UL)                    /*!< System Control Block Base Address */
+
+#define SCB                 ((SCB_Type       *)     SCB_BASE      )   /*!< SCB configuration struct */
+#define SysTick             ((SysTick_Type   *)     SysTick_BASE  )   /*!< SysTick configuration struct */
+#define NVIC                ((NVIC_Type      *)     NVIC_BASE     )   /*!< NVIC configuration struct */
+
+
+/*@} */
+
+
+
+/*******************************************************************************
+ *                Hardware Abstraction Layer
+  Core Function Interface contains:
+  - Core NVIC Functions
+  - Core SysTick Functions
+  - Core Register Access Functions
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference
+*/
+
+
+
+/* ##########################   NVIC functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_NVICFunctions NVIC Functions
+  \brief    Functions that manage interrupts and exceptions via the NVIC.
+  @{
+ */
+
+#ifdef CMSIS_NVIC_VIRTUAL
+  #ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE
+    #define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h"
+  #endif
+  #include CMSIS_NVIC_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetPriorityGrouping    __NVIC_SetPriorityGrouping
+  #define NVIC_GetPriorityGrouping    __NVIC_GetPriorityGrouping
+  #define NVIC_EnableIRQ              __NVIC_EnableIRQ
+  #define NVIC_GetEnableIRQ           __NVIC_GetEnableIRQ
+  #define NVIC_DisableIRQ             __NVIC_DisableIRQ
+  #define NVIC_GetPendingIRQ          __NVIC_GetPendingIRQ
+  #define NVIC_SetPendingIRQ          __NVIC_SetPendingIRQ
+  #define NVIC_ClearPendingIRQ        __NVIC_ClearPendingIRQ
+/*#define NVIC_GetActive              __NVIC_GetActive             not available for Cortex-M0 */
+  #define NVIC_SetPriority            __NVIC_SetPriority
+  #define NVIC_GetPriority            __NVIC_GetPriority
+  #define NVIC_SystemReset            __NVIC_SystemReset
+#endif /* CMSIS_NVIC_VIRTUAL */
+
+#ifdef CMSIS_VECTAB_VIRTUAL
+  #ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+    #define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h"
+  #endif
+  #include CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetVector              __NVIC_SetVector
+  #define NVIC_GetVector              __NVIC_GetVector
+#endif  /* (CMSIS_VECTAB_VIRTUAL) */
+
+#define NVIC_USER_IRQ_OFFSET          16
+
+
+/* The following EXC_RETURN values are saved the LR on exception entry */
+#define EXC_RETURN_HANDLER         (0xFFFFFFF1UL)     /* return to Handler mode, uses MSP after return                               */
+#define EXC_RETURN_THREAD_MSP      (0xFFFFFFF9UL)     /* return to Thread mode, uses MSP after return                                */
+#define EXC_RETURN_THREAD_PSP      (0xFFFFFFFDUL)     /* return to Thread mode, uses PSP after return                                */
+
+
+/* Interrupt Priorities are WORD accessible only under Armv6-M                  */
+/* The following MACROS handle generation of the register offset and byte masks */
+#define _BIT_SHIFT(IRQn)         (  ((((uint32_t)(int32_t)(IRQn))         )      &  0x03UL) * 8UL)
+#define _SHP_IDX(IRQn)           ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >>    2UL)      )
+#define _IP_IDX(IRQn)            (   (((uint32_t)(int32_t)(IRQn))                >>    2UL)      )
+
+#define __NVIC_SetPriorityGrouping(X) (void)(X)
+#define __NVIC_GetPriorityGrouping()  (0U)
+
+/**
+  \brief   Enable Interrupt
+  \details Enables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Enable status
+  \details Returns a device specific interrupt enable status from the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt is not enabled.
+  \return             1  Interrupt is enabled.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Disable Interrupt
+  \details Disables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+    __DSB();
+    __ISB();
+  }
+}
+
+
+/**
+  \brief   Get Pending Interrupt
+  \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt status is not pending.
+  \return             1  Interrupt status is pending.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Set Pending Interrupt
+  \details Sets the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Clear Pending Interrupt
+  \details Clears the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Set Interrupt Priority
+  \details Sets the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]      IRQn  Interrupt number.
+  \param [in]  priority  Priority to set.
+  \note    The priority cannot be set for every processor exception.
+ */
+__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->IP[_IP_IDX(IRQn)]  = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)]  & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+  else
+  {
+    SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Priority
+  \details Reads the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn  Interrupt number.
+  \return             Interrupt Priority.
+                      Value is aligned automatically to the implemented priority bits of the microcontroller.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn)
+{
+
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+  else
+  {
+    return((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+}
+
+
+/**
+  \brief   Encode Priority
+  \details Encodes the priority for an interrupt with the given priority group,
+           preemptive priority value, and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set.
+  \param [in]     PriorityGroup  Used priority group.
+  \param [in]   PreemptPriority  Preemptive priority value (starting from 0).
+  \param [in]       SubPriority  Subpriority value (starting from 0).
+  \return                        Encoded priority. Value can be used in the function \ref NVIC_SetPriority().
+ */
+__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  return (
+           ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) |
+           ((SubPriority     & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL)))
+         );
+}
+
+
+/**
+  \brief   Decode Priority
+  \details Decodes an interrupt priority value with a given priority group to
+           preemptive priority value and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set.
+  \param [in]         Priority   Priority value, which can be retrieved with the function \ref NVIC_GetPriority().
+  \param [in]     PriorityGroup  Used priority group.
+  \param [out] pPreemptPriority  Preemptive priority value (starting from 0).
+  \param [out]     pSubPriority  Subpriority value (starting from 0).
+ */
+__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL);
+  *pSubPriority     = (Priority                   ) & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL);
+}
+
+
+
+/**
+  \brief   Set Interrupt Vector
+  \details Sets an interrupt vector in SRAM based interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+           Address 0 must be mapped to SRAM.
+  \param [in]   IRQn      Interrupt number
+  \param [in]   vector    Address of interrupt handler function
+ */
+__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector;
+}
+
+
+/**
+  \brief   Get Interrupt Vector
+  \details Reads an interrupt vector from interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn      Interrupt number.
+  \return                 Address of interrupt handler function
+ */
+__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET];
+}
+
+
+/**
+  \brief   System Reset
+  \details Initiates a system reset request to reset the MCU.
+ */
+__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void)
+{
+  __DSB();                                                          /* Ensure all outstanding memory accesses included
+                                                                       buffered write are completed before reset */
+  SCB->AIRCR  = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) |
+                 SCB_AIRCR_SYSRESETREQ_Msk);
+  __DSB();                                                          /* Ensure completion of memory access */
+
+  for(;;)                                                           /* wait until reset */
+  {
+    __NOP();
+  }
+}
+
+/*@} end of CMSIS_Core_NVICFunctions */
+
+
+/* ##########################  FPU functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_FpuFunctions FPU Functions
+  \brief    Function that provides FPU type.
+  @{
+ */
+
+/**
+  \brief   get FPU type
+  \details returns the FPU type
+  \returns
+   - \b  0: No FPU
+   - \b  1: Single precision FPU
+   - \b  2: Double + Single precision FPU
+ */
+__STATIC_INLINE uint32_t SCB_GetFPUType(void)
+{
+    return 0U;           /* No FPU */
+}
+
+
+/*@} end of CMSIS_Core_FpuFunctions */
+
+
+
+/* ##################################    SysTick function  ############################################ */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_SysTickFunctions SysTick Functions
+  \brief    Functions that configure the System.
+  @{
+ */
+
+#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U)
+
+/**
+  \brief   System Tick Configuration
+  \details Initializes the System Timer and its interrupt, and starts the System Tick Timer.
+           Counter is in free running mode to generate periodic interrupts.
+  \param [in]  ticks  Number of ticks between two interrupts.
+  \return          0  Function succeeded.
+  \return          1  Function failed.
+  \note    When the variable <b>__Vendor_SysTickConfig</b> is set to 1, then the
+           function <b>SysTick_Config</b> is not included. In this case, the file <b><i>device</i>.h</b>
+           must contain a vendor-specific implementation of this function.
+ */
+__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks)
+{
+  if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk)
+  {
+    return (1UL);                                                   /* Reload value impossible */
+  }
+
+  SysTick->LOAD  = (uint32_t)(ticks - 1UL);                         /* set reload register */
+  NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */
+  SysTick->VAL   = 0UL;                                             /* Load the SysTick Counter Value */
+  SysTick->CTRL  = SysTick_CTRL_CLKSOURCE_Msk |
+                   SysTick_CTRL_TICKINT_Msk   |
+                   SysTick_CTRL_ENABLE_Msk;                         /* Enable SysTick IRQ and SysTick Timer */
+  return (0UL);                                                     /* Function successful */
+}
+
+#endif
+
+/*@} end of CMSIS_Core_SysTickFunctions */
+
+
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM0_H_DEPENDANT */
+
+#endif /* __CMSIS_GENERIC */

LED/Drivers/CMSIS/Include/core_cm1.h

@@ -0,0 +1,976 @@
+/**************************************************************************//**
+ * @file     core_cm1.h
+ * @brief    CMSIS Cortex-M1 Core Peripheral Access Layer Header File
+ * @version  V1.0.0
+ * @date     23. July 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CORE_CM1_H_GENERIC
+#define __CORE_CM1_H_GENERIC
+
+#include <stdint.h>
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/**
+  \page CMSIS_MISRA_Exceptions  MISRA-C:2004 Compliance Exceptions
+  CMSIS violates the following MISRA-C:2004 rules:
+
+   \li Required Rule 8.5, object/function definition in header file.<br>
+     Function definitions in header files are used to allow 'inlining'.
+
+   \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.<br>
+     Unions are used for effective representation of core registers.
+
+   \li Advisory Rule 19.7, Function-like macro defined.<br>
+     Function-like macros are used to allow more efficient code.
+ */
+
+
+/*******************************************************************************
+ *                 CMSIS definitions
+ ******************************************************************************/
+/**
+  \ingroup Cortex_M1
+  @{
+ */
+
+#include "cmsis_version.h"
+ 
+/*  CMSIS CM1 definitions */
+#define __CM1_CMSIS_VERSION_MAIN  (__CM_CMSIS_VERSION_MAIN)              /*!< \deprecated [31:16] CMSIS HAL main version */
+#define __CM1_CMSIS_VERSION_SUB   (__CM_CMSIS_VERSION_SUB)               /*!< \deprecated [15:0]  CMSIS HAL sub version */
+#define __CM1_CMSIS_VERSION       ((__CM1_CMSIS_VERSION_MAIN << 16U) | \
+                                    __CM1_CMSIS_VERSION_SUB           )  /*!< \deprecated CMSIS HAL version number */
+
+#define __CORTEX_M                (1U)                                   /*!< Cortex-M Core */
+
+/** __FPU_USED indicates whether an FPU is used or not.
+    This core does not support an FPU at all
+*/
+#define __FPU_USED       0U
+
+#if defined ( __CC_ARM )
+  #if defined __TARGET_FPU_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #if defined __ARM_PCS_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __GNUC__ )
+  #if defined (__VFP_FP__) && !defined(__SOFTFP__)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __ICCARM__ )
+  #if defined __ARMVFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TI_ARM__ )
+  #if defined __TI_VFP_SUPPORT__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TASKING__ )
+  #if defined __FPU_VFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __CSMC__ )
+  #if ( __CSMC__ & 0x400U)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#endif
+
+#include "cmsis_compiler.h"               /* CMSIS compiler specific defines */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM1_H_GENERIC */
+
+#ifndef __CMSIS_GENERIC
+
+#ifndef __CORE_CM1_H_DEPENDANT
+#define __CORE_CM1_H_DEPENDANT
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* check device defines and use defaults */
+#if defined __CHECK_DEVICE_DEFINES
+  #ifndef __CM1_REV
+    #define __CM1_REV               0x0100U
+    #warning "__CM1_REV not defined in device header file; using default!"
+  #endif
+
+  #ifndef __NVIC_PRIO_BITS
+    #define __NVIC_PRIO_BITS          2U
+    #warning "__NVIC_PRIO_BITS not defined in device header file; using default!"
+  #endif
+
+  #ifndef __Vendor_SysTickConfig
+    #define __Vendor_SysTickConfig    0U
+    #warning "__Vendor_SysTickConfig not defined in device header file; using default!"
+  #endif
+#endif
+
+/* IO definitions (access restrictions to peripheral registers) */
+/**
+    \defgroup CMSIS_glob_defs CMSIS Global Defines
+
+    <strong>IO Type Qualifiers</strong> are used
+    \li to specify the access to peripheral variables.
+    \li for automatic generation of peripheral register debug information.
+*/
+#ifdef __cplusplus
+  #define   __I     volatile             /*!< Defines 'read only' permissions */
+#else
+  #define   __I     volatile const       /*!< Defines 'read only' permissions */
+#endif
+#define     __O     volatile             /*!< Defines 'write only' permissions */
+#define     __IO    volatile             /*!< Defines 'read / write' permissions */
+
+/* following defines should be used for structure members */
+#define     __IM     volatile const      /*! Defines 'read only' structure member permissions */
+#define     __OM     volatile            /*! Defines 'write only' structure member permissions */
+#define     __IOM    volatile            /*! Defines 'read / write' structure member permissions */
+
+/*@} end of group Cortex_M1 */
+
+
+
+/*******************************************************************************
+ *                 Register Abstraction
+  Core Register contain:
+  - Core Register
+  - Core NVIC Register
+  - Core SCB Register
+  - Core SysTick Register
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_core_register Defines and Type Definitions
+  \brief Type definitions and defines for Cortex-M processor based devices.
+*/
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_CORE  Status and Control Registers
+  \brief      Core Register type definitions.
+  @{
+ */
+
+/**
+  \brief  Union type to access the Application Program Status Register (APSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:28;              /*!< bit:  0..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} APSR_Type;
+
+/* APSR Register Definitions */
+#define APSR_N_Pos                         31U                                            /*!< APSR: N Position */
+#define APSR_N_Msk                         (1UL << APSR_N_Pos)                            /*!< APSR: N Mask */
+
+#define APSR_Z_Pos                         30U                                            /*!< APSR: Z Position */
+#define APSR_Z_Msk                         (1UL << APSR_Z_Pos)                            /*!< APSR: Z Mask */
+
+#define APSR_C_Pos                         29U                                            /*!< APSR: C Position */
+#define APSR_C_Msk                         (1UL << APSR_C_Pos)                            /*!< APSR: C Mask */
+
+#define APSR_V_Pos                         28U                                            /*!< APSR: V Position */
+#define APSR_V_Msk                         (1UL << APSR_V_Pos)                            /*!< APSR: V Mask */
+
+
+/**
+  \brief  Union type to access the Interrupt Program Status Register (IPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:23;              /*!< bit:  9..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} IPSR_Type;
+
+/* IPSR Register Definitions */
+#define IPSR_ISR_Pos                        0U                                            /*!< IPSR: ISR Position */
+#define IPSR_ISR_Msk                       (0x1FFUL /*<< IPSR_ISR_Pos*/)                  /*!< IPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Special-Purpose Program Status Registers (xPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:15;              /*!< bit:  9..23  Reserved */
+    uint32_t T:1;                        /*!< bit:     24  Thumb bit        (read 0) */
+    uint32_t _reserved1:3;               /*!< bit: 25..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} xPSR_Type;
+
+/* xPSR Register Definitions */
+#define xPSR_N_Pos                         31U                                            /*!< xPSR: N Position */
+#define xPSR_N_Msk                         (1UL << xPSR_N_Pos)                            /*!< xPSR: N Mask */
+
+#define xPSR_Z_Pos                         30U                                            /*!< xPSR: Z Position */
+#define xPSR_Z_Msk                         (1UL << xPSR_Z_Pos)                            /*!< xPSR: Z Mask */
+
+#define xPSR_C_Pos                         29U                                            /*!< xPSR: C Position */
+#define xPSR_C_Msk                         (1UL << xPSR_C_Pos)                            /*!< xPSR: C Mask */
+
+#define xPSR_V_Pos                         28U                                            /*!< xPSR: V Position */
+#define xPSR_V_Msk                         (1UL << xPSR_V_Pos)                            /*!< xPSR: V Mask */
+
+#define xPSR_T_Pos                         24U                                            /*!< xPSR: T Position */
+#define xPSR_T_Msk                         (1UL << xPSR_T_Pos)                            /*!< xPSR: T Mask */
+
+#define xPSR_ISR_Pos                        0U                                            /*!< xPSR: ISR Position */
+#define xPSR_ISR_Msk                       (0x1FFUL /*<< xPSR_ISR_Pos*/)                  /*!< xPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Control Registers (CONTROL).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:1;               /*!< bit:      0  Reserved */
+    uint32_t SPSEL:1;                    /*!< bit:      1  Stack to be used */
+    uint32_t _reserved1:30;              /*!< bit:  2..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} CONTROL_Type;
+
+/* CONTROL Register Definitions */
+#define CONTROL_SPSEL_Pos                   1U                                            /*!< CONTROL: SPSEL Position */
+#define CONTROL_SPSEL_Msk                  (1UL << CONTROL_SPSEL_Pos)                     /*!< CONTROL: SPSEL Mask */
+
+/*@} end of group CMSIS_CORE */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_NVIC  Nested Vectored Interrupt Controller (NVIC)
+  \brief      Type definitions for the NVIC Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the Nested Vectored Interrupt Controller (NVIC).
+ */
+typedef struct
+{
+  __IOM uint32_t ISER[1U];               /*!< Offset: 0x000 (R/W)  Interrupt Set Enable Register */
+        uint32_t RESERVED0[31U];
+  __IOM uint32_t ICER[1U];               /*!< Offset: 0x080 (R/W)  Interrupt Clear Enable Register */
+        uint32_t RSERVED1[31U];
+  __IOM uint32_t ISPR[1U];               /*!< Offset: 0x100 (R/W)  Interrupt Set Pending Register */
+        uint32_t RESERVED2[31U];
+  __IOM uint32_t ICPR[1U];               /*!< Offset: 0x180 (R/W)  Interrupt Clear Pending Register */
+        uint32_t RESERVED3[31U];
+        uint32_t RESERVED4[64U];
+  __IOM uint32_t IP[8U];                 /*!< Offset: 0x300 (R/W)  Interrupt Priority Register */
+}  NVIC_Type;
+
+/*@} end of group CMSIS_NVIC */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCB     System Control Block (SCB)
+  \brief    Type definitions for the System Control Block Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control Block (SCB).
+ */
+typedef struct
+{
+  __IM  uint32_t CPUID;                  /*!< Offset: 0x000 (R/ )  CPUID Base Register */
+  __IOM uint32_t ICSR;                   /*!< Offset: 0x004 (R/W)  Interrupt Control and State Register */
+        uint32_t RESERVED0;
+  __IOM uint32_t AIRCR;                  /*!< Offset: 0x00C (R/W)  Application Interrupt and Reset Control Register */
+  __IOM uint32_t SCR;                    /*!< Offset: 0x010 (R/W)  System Control Register */
+  __IOM uint32_t CCR;                    /*!< Offset: 0x014 (R/W)  Configuration Control Register */
+        uint32_t RESERVED1;
+  __IOM uint32_t SHP[2U];                /*!< Offset: 0x01C (R/W)  System Handlers Priority Registers. [0] is RESERVED */
+  __IOM uint32_t SHCSR;                  /*!< Offset: 0x024 (R/W)  System Handler Control and State Register */
+} SCB_Type;
+
+/* SCB CPUID Register Definitions */
+#define SCB_CPUID_IMPLEMENTER_Pos          24U                                            /*!< SCB CPUID: IMPLEMENTER Position */
+#define SCB_CPUID_IMPLEMENTER_Msk          (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos)          /*!< SCB CPUID: IMPLEMENTER Mask */
+
+#define SCB_CPUID_VARIANT_Pos              20U                                            /*!< SCB CPUID: VARIANT Position */
+#define SCB_CPUID_VARIANT_Msk              (0xFUL << SCB_CPUID_VARIANT_Pos)               /*!< SCB CPUID: VARIANT Mask */
+
+#define SCB_CPUID_ARCHITECTURE_Pos         16U                                            /*!< SCB CPUID: ARCHITECTURE Position */
+#define SCB_CPUID_ARCHITECTURE_Msk         (0xFUL << SCB_CPUID_ARCHITECTURE_Pos)          /*!< SCB CPUID: ARCHITECTURE Mask */
+
+#define SCB_CPUID_PARTNO_Pos                4U                                            /*!< SCB CPUID: PARTNO Position */
+#define SCB_CPUID_PARTNO_Msk               (0xFFFUL << SCB_CPUID_PARTNO_Pos)              /*!< SCB CPUID: PARTNO Mask */
+
+#define SCB_CPUID_REVISION_Pos              0U                                            /*!< SCB CPUID: REVISION Position */
+#define SCB_CPUID_REVISION_Msk             (0xFUL /*<< SCB_CPUID_REVISION_Pos*/)          /*!< SCB CPUID: REVISION Mask */
+
+/* SCB Interrupt Control State Register Definitions */
+#define SCB_ICSR_NMIPENDSET_Pos            31U                                            /*!< SCB ICSR: NMIPENDSET Position */
+#define SCB_ICSR_NMIPENDSET_Msk            (1UL << SCB_ICSR_NMIPENDSET_Pos)               /*!< SCB ICSR: NMIPENDSET Mask */
+
+#define SCB_ICSR_PENDSVSET_Pos             28U                                            /*!< SCB ICSR: PENDSVSET Position */
+#define SCB_ICSR_PENDSVSET_Msk             (1UL << SCB_ICSR_PENDSVSET_Pos)                /*!< SCB ICSR: PENDSVSET Mask */
+
+#define SCB_ICSR_PENDSVCLR_Pos             27U                                            /*!< SCB ICSR: PENDSVCLR Position */
+#define SCB_ICSR_PENDSVCLR_Msk             (1UL << SCB_ICSR_PENDSVCLR_Pos)                /*!< SCB ICSR: PENDSVCLR Mask */
+
+#define SCB_ICSR_PENDSTSET_Pos             26U                                            /*!< SCB ICSR: PENDSTSET Position */
+#define SCB_ICSR_PENDSTSET_Msk             (1UL << SCB_ICSR_PENDSTSET_Pos)                /*!< SCB ICSR: PENDSTSET Mask */
+
+#define SCB_ICSR_PENDSTCLR_Pos             25U                                            /*!< SCB ICSR: PENDSTCLR Position */
+#define SCB_ICSR_PENDSTCLR_Msk             (1UL << SCB_ICSR_PENDSTCLR_Pos)                /*!< SCB ICSR: PENDSTCLR Mask */
+
+#define SCB_ICSR_ISRPREEMPT_Pos            23U                                            /*!< SCB ICSR: ISRPREEMPT Position */
+#define SCB_ICSR_ISRPREEMPT_Msk            (1UL << SCB_ICSR_ISRPREEMPT_Pos)               /*!< SCB ICSR: ISRPREEMPT Mask */
+
+#define SCB_ICSR_ISRPENDING_Pos            22U                                            /*!< SCB ICSR: ISRPENDING Position */
+#define SCB_ICSR_ISRPENDING_Msk            (1UL << SCB_ICSR_ISRPENDING_Pos)               /*!< SCB ICSR: ISRPENDING Mask */
+
+#define SCB_ICSR_VECTPENDING_Pos           12U                                            /*!< SCB ICSR: VECTPENDING Position */
+#define SCB_ICSR_VECTPENDING_Msk           (0x1FFUL << SCB_ICSR_VECTPENDING_Pos)          /*!< SCB ICSR: VECTPENDING Mask */
+
+#define SCB_ICSR_VECTACTIVE_Pos             0U                                            /*!< SCB ICSR: VECTACTIVE Position */
+#define SCB_ICSR_VECTACTIVE_Msk            (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/)       /*!< SCB ICSR: VECTACTIVE Mask */
+
+/* SCB Application Interrupt and Reset Control Register Definitions */
+#define SCB_AIRCR_VECTKEY_Pos              16U                                            /*!< SCB AIRCR: VECTKEY Position */
+#define SCB_AIRCR_VECTKEY_Msk              (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos)            /*!< SCB AIRCR: VECTKEY Mask */
+
+#define SCB_AIRCR_VECTKEYSTAT_Pos          16U                                            /*!< SCB AIRCR: VECTKEYSTAT Position */
+#define SCB_AIRCR_VECTKEYSTAT_Msk          (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos)        /*!< SCB AIRCR: VECTKEYSTAT Mask */
+
+#define SCB_AIRCR_ENDIANESS_Pos            15U                                            /*!< SCB AIRCR: ENDIANESS Position */
+#define SCB_AIRCR_ENDIANESS_Msk            (1UL << SCB_AIRCR_ENDIANESS_Pos)               /*!< SCB AIRCR: ENDIANESS Mask */
+
+#define SCB_AIRCR_SYSRESETREQ_Pos           2U                                            /*!< SCB AIRCR: SYSRESETREQ Position */
+#define SCB_AIRCR_SYSRESETREQ_Msk          (1UL << SCB_AIRCR_SYSRESETREQ_Pos)             /*!< SCB AIRCR: SYSRESETREQ Mask */
+
+#define SCB_AIRCR_VECTCLRACTIVE_Pos         1U                                            /*!< SCB AIRCR: VECTCLRACTIVE Position */
+#define SCB_AIRCR_VECTCLRACTIVE_Msk        (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos)           /*!< SCB AIRCR: VECTCLRACTIVE Mask */
+
+/* SCB System Control Register Definitions */
+#define SCB_SCR_SEVONPEND_Pos               4U                                            /*!< SCB SCR: SEVONPEND Position */
+#define SCB_SCR_SEVONPEND_Msk              (1UL << SCB_SCR_SEVONPEND_Pos)                 /*!< SCB SCR: SEVONPEND Mask */
+
+#define SCB_SCR_SLEEPDEEP_Pos               2U                                            /*!< SCB SCR: SLEEPDEEP Position */
+#define SCB_SCR_SLEEPDEEP_Msk              (1UL << SCB_SCR_SLEEPDEEP_Pos)                 /*!< SCB SCR: SLEEPDEEP Mask */
+
+#define SCB_SCR_SLEEPONEXIT_Pos             1U                                            /*!< SCB SCR: SLEEPONEXIT Position */
+#define SCB_SCR_SLEEPONEXIT_Msk            (1UL << SCB_SCR_SLEEPONEXIT_Pos)               /*!< SCB SCR: SLEEPONEXIT Mask */
+
+/* SCB Configuration Control Register Definitions */
+#define SCB_CCR_STKALIGN_Pos                9U                                            /*!< SCB CCR: STKALIGN Position */
+#define SCB_CCR_STKALIGN_Msk               (1UL << SCB_CCR_STKALIGN_Pos)                  /*!< SCB CCR: STKALIGN Mask */
+
+#define SCB_CCR_UNALIGN_TRP_Pos             3U                                            /*!< SCB CCR: UNALIGN_TRP Position */
+#define SCB_CCR_UNALIGN_TRP_Msk            (1UL << SCB_CCR_UNALIGN_TRP_Pos)               /*!< SCB CCR: UNALIGN_TRP Mask */
+
+/* SCB System Handler Control and State Register Definitions */
+#define SCB_SHCSR_SVCALLPENDED_Pos         15U                                            /*!< SCB SHCSR: SVCALLPENDED Position */
+#define SCB_SHCSR_SVCALLPENDED_Msk         (1UL << SCB_SHCSR_SVCALLPENDED_Pos)            /*!< SCB SHCSR: SVCALLPENDED Mask */
+
+/*@} end of group CMSIS_SCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCnSCB System Controls not in SCB (SCnSCB)
+  \brief    Type definitions for the System Control and ID Register not in the SCB
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control and ID Register not in the SCB.
+ */
+typedef struct
+{
+        uint32_t RESERVED0[2U];
+  __IOM uint32_t ACTLR;                  /*!< Offset: 0x008 (R/W)  Auxiliary Control Register */
+} SCnSCB_Type;
+
+/* Auxiliary Control Register Definitions */
+#define SCnSCB_ACTLR_ITCMUAEN_Pos            4U                                        /*!< ACTLR: Instruction TCM Upper Alias Enable Position */
+#define SCnSCB_ACTLR_ITCMUAEN_Msk           (1UL << SCnSCB_ACTLR_ITCMUAEN_Pos)         /*!< ACTLR: Instruction TCM Upper Alias Enable Mask */
+
+#define SCnSCB_ACTLR_ITCMLAEN_Pos            3U                                        /*!< ACTLR: Instruction TCM Lower Alias Enable Position */
+#define SCnSCB_ACTLR_ITCMLAEN_Msk           (1UL << SCnSCB_ACTLR_ITCMLAEN_Pos)         /*!< ACTLR: Instruction TCM Lower Alias Enable Mask */
+
+/*@} end of group CMSIS_SCnotSCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SysTick     System Tick Timer (SysTick)
+  \brief    Type definitions for the System Timer Registers.
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Timer (SysTick).
+ */
+typedef struct
+{
+  __IOM uint32_t CTRL;                   /*!< Offset: 0x000 (R/W)  SysTick Control and Status Register */
+  __IOM uint32_t LOAD;                   /*!< Offset: 0x004 (R/W)  SysTick Reload Value Register */
+  __IOM uint32_t VAL;                    /*!< Offset: 0x008 (R/W)  SysTick Current Value Register */
+  __IM  uint32_t CALIB;                  /*!< Offset: 0x00C (R/ )  SysTick Calibration Register */
+} SysTick_Type;
+
+/* SysTick Control / Status Register Definitions */
+#define SysTick_CTRL_COUNTFLAG_Pos         16U                                            /*!< SysTick CTRL: COUNTFLAG Position */
+#define SysTick_CTRL_COUNTFLAG_Msk         (1UL << SysTick_CTRL_COUNTFLAG_Pos)            /*!< SysTick CTRL: COUNTFLAG Mask */
+
+#define SysTick_CTRL_CLKSOURCE_Pos          2U                                            /*!< SysTick CTRL: CLKSOURCE Position */
+#define SysTick_CTRL_CLKSOURCE_Msk         (1UL << SysTick_CTRL_CLKSOURCE_Pos)            /*!< SysTick CTRL: CLKSOURCE Mask */
+
+#define SysTick_CTRL_TICKINT_Pos            1U                                            /*!< SysTick CTRL: TICKINT Position */
+#define SysTick_CTRL_TICKINT_Msk           (1UL << SysTick_CTRL_TICKINT_Pos)              /*!< SysTick CTRL: TICKINT Mask */
+
+#define SysTick_CTRL_ENABLE_Pos             0U                                            /*!< SysTick CTRL: ENABLE Position */
+#define SysTick_CTRL_ENABLE_Msk            (1UL /*<< SysTick_CTRL_ENABLE_Pos*/)           /*!< SysTick CTRL: ENABLE Mask */
+
+/* SysTick Reload Register Definitions */
+#define SysTick_LOAD_RELOAD_Pos             0U                                            /*!< SysTick LOAD: RELOAD Position */
+#define SysTick_LOAD_RELOAD_Msk            (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/)    /*!< SysTick LOAD: RELOAD Mask */
+
+/* SysTick Current Register Definitions */
+#define SysTick_VAL_CURRENT_Pos             0U                                            /*!< SysTick VAL: CURRENT Position */
+#define SysTick_VAL_CURRENT_Msk            (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/)    /*!< SysTick VAL: CURRENT Mask */
+
+/* SysTick Calibration Register Definitions */
+#define SysTick_CALIB_NOREF_Pos            31U                                            /*!< SysTick CALIB: NOREF Position */
+#define SysTick_CALIB_NOREF_Msk            (1UL << SysTick_CALIB_NOREF_Pos)               /*!< SysTick CALIB: NOREF Mask */
+
+#define SysTick_CALIB_SKEW_Pos             30U                                            /*!< SysTick CALIB: SKEW Position */
+#define SysTick_CALIB_SKEW_Msk             (1UL << SysTick_CALIB_SKEW_Pos)                /*!< SysTick CALIB: SKEW Mask */
+
+#define SysTick_CALIB_TENMS_Pos             0U                                            /*!< SysTick CALIB: TENMS Position */
+#define SysTick_CALIB_TENMS_Msk            (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/)    /*!< SysTick CALIB: TENMS Mask */
+
+/*@} end of group CMSIS_SysTick */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_CoreDebug       Core Debug Registers (CoreDebug)
+  \brief    Cortex-M1 Core Debug Registers (DCB registers, SHCSR, and DFSR) are only accessible over DAP and not via processor.
+            Therefore they are not covered by the Cortex-M1 header file.
+  @{
+ */
+/*@} end of group CMSIS_CoreDebug */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_bitfield     Core register bit field macros
+  \brief      Macros for use with bit field definitions (xxx_Pos, xxx_Msk).
+  @{
+ */
+
+/**
+  \brief   Mask and shift a bit field value for use in a register bit range.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of the bit field. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted value.
+*/
+#define _VAL2FLD(field, value)    (((uint32_t)(value) << field ## _Pos) & field ## _Msk)
+
+/**
+  \brief     Mask and shift a register value to extract a bit filed value.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of register. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted bit field value.
+*/
+#define _FLD2VAL(field, value)    (((uint32_t)(value) & field ## _Msk) >> field ## _Pos)
+
+/*@} end of group CMSIS_core_bitfield */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_base     Core Definitions
+  \brief      Definitions for base addresses, unions, and structures.
+  @{
+ */
+
+/* Memory mapping of Core Hardware */
+#define SCS_BASE            (0xE000E000UL)                            /*!< System Control Space Base Address */
+#define SysTick_BASE        (SCS_BASE +  0x0010UL)                    /*!< SysTick Base Address */
+#define NVIC_BASE           (SCS_BASE +  0x0100UL)                    /*!< NVIC Base Address */
+#define SCB_BASE            (SCS_BASE +  0x0D00UL)                    /*!< System Control Block Base Address */
+
+#define SCnSCB              ((SCnSCB_Type    *)     SCS_BASE      )   /*!< System control Register not in SCB */
+#define SCB                 ((SCB_Type       *)     SCB_BASE      )   /*!< SCB configuration struct */
+#define SysTick             ((SysTick_Type   *)     SysTick_BASE  )   /*!< SysTick configuration struct */
+#define NVIC                ((NVIC_Type      *)     NVIC_BASE     )   /*!< NVIC configuration struct */
+
+
+/*@} */
+
+
+
+/*******************************************************************************
+ *                Hardware Abstraction Layer
+  Core Function Interface contains:
+  - Core NVIC Functions
+  - Core SysTick Functions
+  - Core Register Access Functions
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference
+*/
+
+
+
+/* ##########################   NVIC functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_NVICFunctions NVIC Functions
+  \brief    Functions that manage interrupts and exceptions via the NVIC.
+  @{
+ */
+
+#ifdef CMSIS_NVIC_VIRTUAL
+  #ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE
+    #define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h"
+  #endif
+  #include CMSIS_NVIC_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetPriorityGrouping    __NVIC_SetPriorityGrouping
+  #define NVIC_GetPriorityGrouping    __NVIC_GetPriorityGrouping
+  #define NVIC_EnableIRQ              __NVIC_EnableIRQ
+  #define NVIC_GetEnableIRQ           __NVIC_GetEnableIRQ
+  #define NVIC_DisableIRQ             __NVIC_DisableIRQ
+  #define NVIC_GetPendingIRQ          __NVIC_GetPendingIRQ
+  #define NVIC_SetPendingIRQ          __NVIC_SetPendingIRQ
+  #define NVIC_ClearPendingIRQ        __NVIC_ClearPendingIRQ
+/*#define NVIC_GetActive              __NVIC_GetActive             not available for Cortex-M1 */
+  #define NVIC_SetPriority            __NVIC_SetPriority
+  #define NVIC_GetPriority            __NVIC_GetPriority
+  #define NVIC_SystemReset            __NVIC_SystemReset
+#endif /* CMSIS_NVIC_VIRTUAL */
+
+#ifdef CMSIS_VECTAB_VIRTUAL
+  #ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+    #define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h"
+  #endif
+  #include CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetVector              __NVIC_SetVector
+  #define NVIC_GetVector              __NVIC_GetVector
+#endif  /* (CMSIS_VECTAB_VIRTUAL) */
+
+#define NVIC_USER_IRQ_OFFSET          16
+
+
+/* The following EXC_RETURN values are saved the LR on exception entry */
+#define EXC_RETURN_HANDLER         (0xFFFFFFF1UL)     /* return to Handler mode, uses MSP after return                               */
+#define EXC_RETURN_THREAD_MSP      (0xFFFFFFF9UL)     /* return to Thread mode, uses MSP after return                                */
+#define EXC_RETURN_THREAD_PSP      (0xFFFFFFFDUL)     /* return to Thread mode, uses PSP after return                                */
+
+
+/* Interrupt Priorities are WORD accessible only under Armv6-M                  */
+/* The following MACROS handle generation of the register offset and byte masks */
+#define _BIT_SHIFT(IRQn)         (  ((((uint32_t)(int32_t)(IRQn))         )      &  0x03UL) * 8UL)
+#define _SHP_IDX(IRQn)           ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >>    2UL)      )
+#define _IP_IDX(IRQn)            (   (((uint32_t)(int32_t)(IRQn))                >>    2UL)      )
+
+#define __NVIC_SetPriorityGrouping(X) (void)(X)
+#define __NVIC_GetPriorityGrouping()  (0U)
+
+/**
+  \brief   Enable Interrupt
+  \details Enables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Enable status
+  \details Returns a device specific interrupt enable status from the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt is not enabled.
+  \return             1  Interrupt is enabled.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Disable Interrupt
+  \details Disables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+    __DSB();
+    __ISB();
+  }
+}
+
+
+/**
+  \brief   Get Pending Interrupt
+  \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt status is not pending.
+  \return             1  Interrupt status is pending.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Set Pending Interrupt
+  \details Sets the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Clear Pending Interrupt
+  \details Clears the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Set Interrupt Priority
+  \details Sets the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]      IRQn  Interrupt number.
+  \param [in]  priority  Priority to set.
+  \note    The priority cannot be set for every processor exception.
+ */
+__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->IP[_IP_IDX(IRQn)]  = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)]  & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+  else
+  {
+    SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Priority
+  \details Reads the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn  Interrupt number.
+  \return             Interrupt Priority.
+                      Value is aligned automatically to the implemented priority bits of the microcontroller.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn)
+{
+
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+  else
+  {
+    return((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+}
+
+
+/**
+  \brief   Encode Priority
+  \details Encodes the priority for an interrupt with the given priority group,
+           preemptive priority value, and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set.
+  \param [in]     PriorityGroup  Used priority group.
+  \param [in]   PreemptPriority  Preemptive priority value (starting from 0).
+  \param [in]       SubPriority  Subpriority value (starting from 0).
+  \return                        Encoded priority. Value can be used in the function \ref NVIC_SetPriority().
+ */
+__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  return (
+           ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) |
+           ((SubPriority     & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL)))
+         );
+}
+
+
+/**
+  \brief   Decode Priority
+  \details Decodes an interrupt priority value with a given priority group to
+           preemptive priority value and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set.
+  \param [in]         Priority   Priority value, which can be retrieved with the function \ref NVIC_GetPriority().
+  \param [in]     PriorityGroup  Used priority group.
+  \param [out] pPreemptPriority  Preemptive priority value (starting from 0).
+  \param [out]     pSubPriority  Subpriority value (starting from 0).
+ */
+__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL);
+  *pSubPriority     = (Priority                   ) & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL);
+}
+
+
+
+/**
+  \brief   Set Interrupt Vector
+  \details Sets an interrupt vector in SRAM based interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+           Address 0 must be mapped to SRAM.
+  \param [in]   IRQn      Interrupt number
+  \param [in]   vector    Address of interrupt handler function
+ */
+__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector;
+}
+
+
+/**
+  \brief   Get Interrupt Vector
+  \details Reads an interrupt vector from interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn      Interrupt number.
+  \return                 Address of interrupt handler function
+ */
+__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET];
+}
+
+
+/**
+  \brief   System Reset
+  \details Initiates a system reset request to reset the MCU.
+ */
+__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void)
+{
+  __DSB();                                                          /* Ensure all outstanding memory accesses included
+                                                                       buffered write are completed before reset */
+  SCB->AIRCR  = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) |
+                 SCB_AIRCR_SYSRESETREQ_Msk);
+  __DSB();                                                          /* Ensure completion of memory access */
+
+  for(;;)                                                           /* wait until reset */
+  {
+    __NOP();
+  }
+}
+
+/*@} end of CMSIS_Core_NVICFunctions */
+
+
+/* ##########################  FPU functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_FpuFunctions FPU Functions
+  \brief    Function that provides FPU type.
+  @{
+ */
+
+/**
+  \brief   get FPU type
+  \details returns the FPU type
+  \returns
+   - \b  0: No FPU
+   - \b  1: Single precision FPU
+   - \b  2: Double + Single precision FPU
+ */
+__STATIC_INLINE uint32_t SCB_GetFPUType(void)
+{
+    return 0U;           /* No FPU */
+}
+
+
+/*@} end of CMSIS_Core_FpuFunctions */
+
+
+
+/* ##################################    SysTick function  ############################################ */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_SysTickFunctions SysTick Functions
+  \brief    Functions that configure the System.
+  @{
+ */
+
+#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U)
+
+/**
+  \brief   System Tick Configuration
+  \details Initializes the System Timer and its interrupt, and starts the System Tick Timer.
+           Counter is in free running mode to generate periodic interrupts.
+  \param [in]  ticks  Number of ticks between two interrupts.
+  \return          0  Function succeeded.
+  \return          1  Function failed.
+  \note    When the variable <b>__Vendor_SysTickConfig</b> is set to 1, then the
+           function <b>SysTick_Config</b> is not included. In this case, the file <b><i>device</i>.h</b>
+           must contain a vendor-specific implementation of this function.
+ */
+__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks)
+{
+  if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk)
+  {
+    return (1UL);                                                   /* Reload value impossible */
+  }
+
+  SysTick->LOAD  = (uint32_t)(ticks - 1UL);                         /* set reload register */
+  NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */
+  SysTick->VAL   = 0UL;                                             /* Load the SysTick Counter Value */
+  SysTick->CTRL  = SysTick_CTRL_CLKSOURCE_Msk |
+                   SysTick_CTRL_TICKINT_Msk   |
+                   SysTick_CTRL_ENABLE_Msk;                         /* Enable SysTick IRQ and SysTick Timer */
+  return (0UL);                                                     /* Function successful */
+}
+
+#endif
+
+/*@} end of CMSIS_Core_SysTickFunctions */
+
+
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM1_H_DEPENDANT */
+
+#endif /* __CMSIS_GENERIC */

LED/Drivers/CMSIS/Include/mpu_armv7.h

@@ -0,0 +1,270 @@
+/******************************************************************************
+ * @file     mpu_armv7.h
+ * @brief    CMSIS MPU API for Armv7-M MPU
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+ 
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header    /* treat file as system include file */
+#endif
+ 
+#ifndef ARM_MPU_ARMV7_H
+#define ARM_MPU_ARMV7_H
+
+#define ARM_MPU_REGION_SIZE_32B      ((uint8_t)0x04U) ///!< MPU Region Size 32 Bytes
+#define ARM_MPU_REGION_SIZE_64B      ((uint8_t)0x05U) ///!< MPU Region Size 64 Bytes
+#define ARM_MPU_REGION_SIZE_128B     ((uint8_t)0x06U) ///!< MPU Region Size 128 Bytes
+#define ARM_MPU_REGION_SIZE_256B     ((uint8_t)0x07U) ///!< MPU Region Size 256 Bytes
+#define ARM_MPU_REGION_SIZE_512B     ((uint8_t)0x08U) ///!< MPU Region Size 512 Bytes
+#define ARM_MPU_REGION_SIZE_1KB      ((uint8_t)0x09U) ///!< MPU Region Size 1 KByte
+#define ARM_MPU_REGION_SIZE_2KB      ((uint8_t)0x0AU) ///!< MPU Region Size 2 KBytes
+#define ARM_MPU_REGION_SIZE_4KB      ((uint8_t)0x0BU) ///!< MPU Region Size 4 KBytes
+#define ARM_MPU_REGION_SIZE_8KB      ((uint8_t)0x0CU) ///!< MPU Region Size 8 KBytes
+#define ARM_MPU_REGION_SIZE_16KB     ((uint8_t)0x0DU) ///!< MPU Region Size 16 KBytes
+#define ARM_MPU_REGION_SIZE_32KB     ((uint8_t)0x0EU) ///!< MPU Region Size 32 KBytes
+#define ARM_MPU_REGION_SIZE_64KB     ((uint8_t)0x0FU) ///!< MPU Region Size 64 KBytes
+#define ARM_MPU_REGION_SIZE_128KB    ((uint8_t)0x10U) ///!< MPU Region Size 128 KBytes
+#define ARM_MPU_REGION_SIZE_256KB    ((uint8_t)0x11U) ///!< MPU Region Size 256 KBytes
+#define ARM_MPU_REGION_SIZE_512KB    ((uint8_t)0x12U) ///!< MPU Region Size 512 KBytes
+#define ARM_MPU_REGION_SIZE_1MB      ((uint8_t)0x13U) ///!< MPU Region Size 1 MByte
+#define ARM_MPU_REGION_SIZE_2MB      ((uint8_t)0x14U) ///!< MPU Region Size 2 MBytes
+#define ARM_MPU_REGION_SIZE_4MB      ((uint8_t)0x15U) ///!< MPU Region Size 4 MBytes
+#define ARM_MPU_REGION_SIZE_8MB      ((uint8_t)0x16U) ///!< MPU Region Size 8 MBytes
+#define ARM_MPU_REGION_SIZE_16MB     ((uint8_t)0x17U) ///!< MPU Region Size 16 MBytes
+#define ARM_MPU_REGION_SIZE_32MB     ((uint8_t)0x18U) ///!< MPU Region Size 32 MBytes
+#define ARM_MPU_REGION_SIZE_64MB     ((uint8_t)0x19U) ///!< MPU Region Size 64 MBytes
+#define ARM_MPU_REGION_SIZE_128MB    ((uint8_t)0x1AU) ///!< MPU Region Size 128 MBytes
+#define ARM_MPU_REGION_SIZE_256MB    ((uint8_t)0x1BU) ///!< MPU Region Size 256 MBytes
+#define ARM_MPU_REGION_SIZE_512MB    ((uint8_t)0x1CU) ///!< MPU Region Size 512 MBytes
+#define ARM_MPU_REGION_SIZE_1GB      ((uint8_t)0x1DU) ///!< MPU Region Size 1 GByte
+#define ARM_MPU_REGION_SIZE_2GB      ((uint8_t)0x1EU) ///!< MPU Region Size 2 GBytes
+#define ARM_MPU_REGION_SIZE_4GB      ((uint8_t)0x1FU) ///!< MPU Region Size 4 GBytes
+
+#define ARM_MPU_AP_NONE 0U ///!< MPU Access Permission no access
+#define ARM_MPU_AP_PRIV 1U ///!< MPU Access Permission privileged access only
+#define ARM_MPU_AP_URO  2U ///!< MPU Access Permission unprivileged access read-only
+#define ARM_MPU_AP_FULL 3U ///!< MPU Access Permission full access
+#define ARM_MPU_AP_PRO  5U ///!< MPU Access Permission privileged access read-only
+#define ARM_MPU_AP_RO   6U ///!< MPU Access Permission read-only access
+
+/** MPU Region Base Address Register Value
+*
+* \param Region The region to be configured, number 0 to 15.
+* \param BaseAddress The base address for the region.
+*/
+#define ARM_MPU_RBAR(Region, BaseAddress) \
+  (((BaseAddress) & MPU_RBAR_ADDR_Msk) |  \
+   ((Region) & MPU_RBAR_REGION_Msk)    |  \
+   (MPU_RBAR_VALID_Msk))
+
+/**
+* MPU Memory Access Attributes
+* 
+* \param TypeExtField      Type extension field, allows you to configure memory access type, for example strongly ordered, peripheral.
+* \param IsShareable       Region is shareable between multiple bus masters.
+* \param IsCacheable       Region is cacheable, i.e. its value may be kept in cache.
+* \param IsBufferable      Region is bufferable, i.e. using write-back caching. Cacheable but non-bufferable regions use write-through policy.
+*/  
+#define ARM_MPU_ACCESS_(TypeExtField, IsShareable, IsCacheable, IsBufferable)   \
+  ((((TypeExtField ) << MPU_RASR_TEX_Pos) & MPU_RASR_TEX_Msk)                 | \
+   (((IsShareable ) << MPU_RASR_S_Pos) & MPU_RASR_S_Msk)                      | \
+   (((IsCacheable ) << MPU_RASR_C_Pos) & MPU_RASR_C_Msk)                      | \
+   (((IsBufferable ) << MPU_RASR_B_Pos) & MPU_RASR_B_Msk))
+
+/**
+* MPU Region Attribute and Size Register Value
+* 
+* \param DisableExec       Instruction access disable bit, 1= disable instruction fetches.
+* \param AccessPermission  Data access permissions, allows you to configure read/write access for User and Privileged mode.
+* \param AccessAttributes  Memory access attribution, see \ref ARM_MPU_ACCESS_.
+* \param SubRegionDisable  Sub-region disable field.
+* \param Size              Region size of the region to be configured, for example 4K, 8K.
+*/
+#define ARM_MPU_RASR_EX(DisableExec, AccessPermission, AccessAttributes, SubRegionDisable, Size)      \
+  ((((DisableExec ) << MPU_RASR_XN_Pos) & MPU_RASR_XN_Msk)                                          | \
+   (((AccessPermission) << MPU_RASR_AP_Pos) & MPU_RASR_AP_Msk)                                      | \
+   (((AccessAttributes) ) & (MPU_RASR_TEX_Msk | MPU_RASR_S_Msk | MPU_RASR_C_Msk | MPU_RASR_B_Msk)))
+  
+/**
+* MPU Region Attribute and Size Register Value
+* 
+* \param DisableExec       Instruction access disable bit, 1= disable instruction fetches.
+* \param AccessPermission  Data access permissions, allows you to configure read/write access for User and Privileged mode.
+* \param TypeExtField      Type extension field, allows you to configure memory access type, for example strongly ordered, peripheral.
+* \param IsShareable       Region is shareable between multiple bus masters.
+* \param IsCacheable       Region is cacheable, i.e. its value may be kept in cache.
+* \param IsBufferable      Region is bufferable, i.e. using write-back caching. Cacheable but non-bufferable regions use write-through policy.
+* \param SubRegionDisable  Sub-region disable field.
+* \param Size              Region size of the region to be configured, for example 4K, 8K.
+*/                         
+#define ARM_MPU_RASR(DisableExec, AccessPermission, TypeExtField, IsShareable, IsCacheable, IsBufferable, SubRegionDisable, Size) \
+  ARM_MPU_RASR_EX(DisableExec, AccessPermission, ARM_MPU_ACCESS_(TypeExtField, IsShareable, IsCacheable, IsBufferable), SubRegionDisable, Size)
+
+/**
+* MPU Memory Access Attribute for strongly ordered memory.
+*  - TEX: 000b
+*  - Shareable
+*  - Non-cacheable
+*  - Non-bufferable
+*/ 
+#define ARM_MPU_ACCESS_ORDERED ARM_MPU_ACCESS_(0U, 1U, 0U, 0U)
+
+/**
+* MPU Memory Access Attribute for device memory.
+*  - TEX: 000b (if non-shareable) or 010b (if shareable)
+*  - Shareable or non-shareable
+*  - Non-cacheable
+*  - Bufferable (if shareable) or non-bufferable (if non-shareable)
+*
+* \param IsShareable Configures the device memory as shareable or non-shareable.
+*/ 
+#define ARM_MPU_ACCESS_DEVICE(IsShareable) ((IsShareable) ? ARM_MPU_ACCESS_(0U, 1U, 0U, 1U) : ARM_MPU_ACCESS_(2U, 0U, 0U, 0U))
+
+/**
+* MPU Memory Access Attribute for normal memory.
+*  - TEX: 1BBb (reflecting outer cacheability rules)
+*  - Shareable or non-shareable
+*  - Cacheable or non-cacheable (reflecting inner cacheability rules)
+*  - Bufferable or non-bufferable (reflecting inner cacheability rules)
+*
+* \param OuterCp Configures the outer cache policy.
+* \param InnerCp Configures the inner cache policy.
+* \param IsShareable Configures the memory as shareable or non-shareable.
+*/ 
+#define ARM_MPU_ACCESS_NORMAL(OuterCp, InnerCp, IsShareable) ARM_MPU_ACCESS_((4U | (OuterCp)), IsShareable, ((InnerCp) & 2U), ((InnerCp) & 1U))
+
+/**
+* MPU Memory Access Attribute non-cacheable policy.
+*/
+#define ARM_MPU_CACHEP_NOCACHE 0U
+
+/**
+* MPU Memory Access Attribute write-back, write and read allocate policy.
+*/
+#define ARM_MPU_CACHEP_WB_WRA 1U
+
+/**
+* MPU Memory Access Attribute write-through, no write allocate policy.
+*/
+#define ARM_MPU_CACHEP_WT_NWA 2U
+
+/**
+* MPU Memory Access Attribute write-back, no write allocate policy.
+*/
+#define ARM_MPU_CACHEP_WB_NWA 3U
+
+
+/**
+* Struct for a single MPU Region
+*/
+typedef struct {
+  uint32_t RBAR; //!< The region base address register value (RBAR)
+  uint32_t RASR; //!< The region attribute and size register value (RASR) \ref MPU_RASR
+} ARM_MPU_Region_t;
+    
+/** Enable the MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+
+/** Clear and disable the given MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion(uint32_t rnr)
+{
+  MPU->RNR = rnr;
+  MPU->RASR = 0U;
+}
+
+/** Configure an MPU region.
+* \param rbar Value for RBAR register.
+* \param rsar Value for RSAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion(uint32_t rbar, uint32_t rasr)
+{
+  MPU->RBAR = rbar;
+  MPU->RASR = rasr;
+}
+
+/** Configure the given MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rsar Value for RSAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegionEx(uint32_t rnr, uint32_t rbar, uint32_t rasr)
+{
+  MPU->RNR = rnr;
+  MPU->RBAR = rbar;
+  MPU->RASR = rasr;
+}
+
+/** Memcopy with strictly ordered memory access, e.g. for register targets.
+* \param dst Destination data is copied to.
+* \param src Source data is copied from.
+* \param len Amount of data words to be copied.
+*/
+__STATIC_INLINE void orderedCpy(volatile uint32_t* dst, const uint32_t* __RESTRICT src, uint32_t len)
+{
+  uint32_t i;
+  for (i = 0U; i < len; ++i) 
+  {
+    dst[i] = src[i];
+  }
+}
+
+/** Load the given number of MPU regions from a table.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load(ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  const uint32_t rowWordSize = sizeof(ARM_MPU_Region_t)/4U;
+  while (cnt > MPU_TYPE_RALIASES) {
+    orderedCpy(&(MPU->RBAR), &(table->RBAR), MPU_TYPE_RALIASES*rowWordSize);
+    table += MPU_TYPE_RALIASES;
+    cnt -= MPU_TYPE_RALIASES;
+  }
+  orderedCpy(&(MPU->RBAR), &(table->RBAR), cnt*rowWordSize);
+}
+
+#endif

LED/Drivers/CMSIS/Include/mpu_armv8.h

@@ -0,0 +1,333 @@
+/******************************************************************************
+ * @file     mpu_armv8.h
+ * @brief    CMSIS MPU API for Armv8-M MPU
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header    /* treat file as system include file */
+#endif
+
+#ifndef ARM_MPU_ARMV8_H
+#define ARM_MPU_ARMV8_H
+
+/** \brief Attribute for device memory (outer only) */
+#define ARM_MPU_ATTR_DEVICE                           ( 0U )
+
+/** \brief Attribute for non-cacheable, normal memory */
+#define ARM_MPU_ATTR_NON_CACHEABLE                    ( 4U )
+
+/** \brief Attribute for normal memory (outer and inner)
+* \param NT Non-Transient: Set to 1 for non-transient data.
+* \param WB Write-Back: Set to 1 to use write-back update policy.
+* \param RA Read Allocation: Set to 1 to use cache allocation on read miss.
+* \param WA Write Allocation: Set to 1 to use cache allocation on write miss.
+*/
+#define ARM_MPU_ATTR_MEMORY_(NT, WB, RA, WA) \
+  (((NT & 1U) << 3U) | ((WB & 1U) << 2U) | ((RA & 1U) << 1U) | (WA & 1U))
+
+/** \brief Device memory type non Gathering, non Re-ordering, non Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGnRnE (0U)
+
+/** \brief Device memory type non Gathering, non Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGnRE  (1U)
+
+/** \brief Device memory type non Gathering, Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGRE   (2U)
+
+/** \brief Device memory type Gathering, Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_GRE    (3U)
+
+/** \brief Memory Attribute
+* \param O Outer memory attributes
+* \param I O == ARM_MPU_ATTR_DEVICE: Device memory attributes, else: Inner memory attributes
+*/
+#define ARM_MPU_ATTR(O, I) (((O & 0xFU) << 4U) | (((O & 0xFU) != 0U) ? (I & 0xFU) : ((I & 0x3U) << 2U)))
+
+/** \brief Normal memory non-shareable  */
+#define ARM_MPU_SH_NON   (0U)
+
+/** \brief Normal memory outer shareable  */
+#define ARM_MPU_SH_OUTER (2U)
+
+/** \brief Normal memory inner shareable  */
+#define ARM_MPU_SH_INNER (3U)
+
+/** \brief Memory access permissions
+* \param RO Read-Only: Set to 1 for read-only memory.
+* \param NP Non-Privileged: Set to 1 for non-privileged memory.
+*/
+#define ARM_MPU_AP_(RO, NP) (((RO & 1U) << 1U) | (NP & 1U))
+
+/** \brief Region Base Address Register value
+* \param BASE The base address bits [31:5] of a memory region. The value is zero extended. Effective address gets 32 byte aligned.
+* \param SH Defines the Shareability domain for this memory region.
+* \param RO Read-Only: Set to 1 for a read-only memory region.
+* \param NP Non-Privileged: Set to 1 for a non-privileged memory region.
+* \oaram XN eXecute Never: Set to 1 for a non-executable memory region.
+*/
+#define ARM_MPU_RBAR(BASE, SH, RO, NP, XN) \
+  ((BASE & MPU_RBAR_BASE_Msk) | \
+  ((SH << MPU_RBAR_SH_Pos) & MPU_RBAR_SH_Msk) | \
+  ((ARM_MPU_AP_(RO, NP) << MPU_RBAR_AP_Pos) & MPU_RBAR_AP_Msk) | \
+  ((XN << MPU_RBAR_XN_Pos) & MPU_RBAR_XN_Msk))
+
+/** \brief Region Limit Address Register value
+* \param LIMIT The limit address bits [31:5] for this memory region. The value is one extended.
+* \param IDX The attribute index to be associated with this memory region.
+*/
+#define ARM_MPU_RLAR(LIMIT, IDX) \
+  ((LIMIT & MPU_RLAR_LIMIT_Msk) | \
+  ((IDX << MPU_RLAR_AttrIndx_Pos) & MPU_RLAR_AttrIndx_Msk) | \
+  (MPU_RLAR_EN_Msk))
+
+/**
+* Struct for a single MPU Region
+*/
+typedef struct {
+  uint32_t RBAR;                   /*!< Region Base Address Register value */
+  uint32_t RLAR;                   /*!< Region Limit Address Register value */
+} ARM_MPU_Region_t;
+    
+/** Enable the MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+
+#ifdef MPU_NS
+/** Enable the Non-secure MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable_NS(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU_NS->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB_NS->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the Non-secure MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable_NS(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB_NS->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU_NS->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+#endif
+
+/** Set the memory attribute encoding to the given MPU.
+* \param mpu Pointer to the MPU to be configured.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttrEx(MPU_Type* mpu, uint8_t idx, uint8_t attr)
+{
+  const uint8_t reg = idx / 4U;
+  const uint32_t pos = ((idx % 4U) * 8U);
+  const uint32_t mask = 0xFFU << pos;
+  
+  if (reg >= (sizeof(mpu->MAIR) / sizeof(mpu->MAIR[0]))) {
+    return; // invalid index
+  }
+  
+  mpu->MAIR[reg] = ((mpu->MAIR[reg] & ~mask) | ((attr << pos) & mask));
+}
+
+/** Set the memory attribute encoding.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttr(uint8_t idx, uint8_t attr)
+{
+  ARM_MPU_SetMemAttrEx(MPU, idx, attr);
+}
+
+#ifdef MPU_NS
+/** Set the memory attribute encoding to the Non-secure MPU.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttr_NS(uint8_t idx, uint8_t attr)
+{
+  ARM_MPU_SetMemAttrEx(MPU_NS, idx, attr);
+}
+#endif
+
+/** Clear and disable the given MPU region of the given MPU.
+* \param mpu Pointer to MPU to be used.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegionEx(MPU_Type* mpu, uint32_t rnr)
+{
+  mpu->RNR = rnr;
+  mpu->RLAR = 0U;
+}
+
+/** Clear and disable the given MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion(uint32_t rnr)
+{
+  ARM_MPU_ClrRegionEx(MPU, rnr);
+}
+
+#ifdef MPU_NS
+/** Clear and disable the given Non-secure MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion_NS(uint32_t rnr)
+{  
+  ARM_MPU_ClrRegionEx(MPU_NS, rnr);
+}
+#endif
+
+/** Configure the given MPU region of the given MPU.
+* \param mpu Pointer to MPU to be used.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegionEx(MPU_Type* mpu, uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  mpu->RNR = rnr;
+  mpu->RBAR = rbar;
+  mpu->RLAR = rlar;
+}
+
+/** Configure the given MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion(uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  ARM_MPU_SetRegionEx(MPU, rnr, rbar, rlar);
+}
+
+#ifdef MPU_NS
+/** Configure the given Non-secure MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion_NS(uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  ARM_MPU_SetRegionEx(MPU_NS, rnr, rbar, rlar);  
+}
+#endif
+
+/** Memcopy with strictly ordered memory access, e.g. for register targets.
+* \param dst Destination data is copied to.
+* \param src Source data is copied from.
+* \param len Amount of data words to be copied.
+*/
+__STATIC_INLINE void orderedCpy(volatile uint32_t* dst, const uint32_t* __RESTRICT src, uint32_t len)
+{
+  uint32_t i;
+  for (i = 0U; i < len; ++i) 
+  {
+    dst[i] = src[i];
+  }
+}
+
+/** Load the given number of MPU regions from a table to the given MPU.
+* \param mpu Pointer to the MPU registers to be used.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_LoadEx(MPU_Type* mpu, uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  const uint32_t rowWordSize = sizeof(ARM_MPU_Region_t)/4U;
+  if (cnt == 1U) {
+    mpu->RNR = rnr;
+    orderedCpy(&(mpu->RBAR), &(table->RBAR), rowWordSize);
+  } else {
+    uint32_t rnrBase   = rnr & ~(MPU_TYPE_RALIASES-1U);
+    uint32_t rnrOffset = rnr % MPU_TYPE_RALIASES;
+    
+    mpu->RNR = rnrBase;
+    while ((rnrOffset + cnt) > MPU_TYPE_RALIASES) {
+      uint32_t c = MPU_TYPE_RALIASES - rnrOffset;
+      orderedCpy(&(mpu->RBAR)+(rnrOffset*2U), &(table->RBAR), c*rowWordSize);
+      table += c;
+      cnt -= c;
+      rnrOffset = 0U;
+      rnrBase += MPU_TYPE_RALIASES;
+      mpu->RNR = rnrBase;
+    }
+    
+    orderedCpy(&(mpu->RBAR)+(rnrOffset*2U), &(table->RBAR), cnt*rowWordSize);
+  }
+}
+
+/** Load the given number of MPU regions from a table.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load(uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  ARM_MPU_LoadEx(MPU, rnr, table, cnt);
+}
+
+#ifdef MPU_NS
+/** Load the given number of MPU regions from a table to the Non-secure MPU.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load_NS(uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  ARM_MPU_LoadEx(MPU_NS, rnr, table, cnt);
+}
+#endif
+
+#endif
+

LED/Drivers/CMSIS/Include/tz_context.h

@@ -0,0 +1,70 @@
+/******************************************************************************
+ * @file     tz_context.h
+ * @brief    Context Management for Armv8-M TrustZone
+ * @version  V1.0.1
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef TZ_CONTEXT_H
+#define TZ_CONTEXT_H
+ 
+#include <stdint.h>
+ 
+#ifndef TZ_MODULEID_T
+#define TZ_MODULEID_T
+/// \details Data type that identifies secure software modules called by a process.
+typedef uint32_t TZ_ModuleId_t;
+#endif
+ 
+/// \details TZ Memory ID identifies an allocated memory slot.
+typedef uint32_t TZ_MemoryId_t;
+  
+/// Initialize secure context memory system
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_InitContextSystem_S (void);
+ 
+/// Allocate context memory for calling secure software modules in TrustZone
+/// \param[in]  module   identifies software modules called from non-secure mode
+/// \return value != 0 id TrustZone memory slot identifier
+/// \return value 0    no memory available or internal error
+TZ_MemoryId_t TZ_AllocModuleContext_S (TZ_ModuleId_t module);
+ 
+/// Free context memory that was previously allocated with \ref TZ_AllocModuleContext_S
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_FreeModuleContext_S (TZ_MemoryId_t id);
+ 
+/// Load secure context (called on RTOS thread context switch)
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_LoadContext_S (TZ_MemoryId_t id);
+ 
+/// Store secure context (called on RTOS thread context switch)
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_StoreContext_S (TZ_MemoryId_t id);
+ 
+#endif  // TZ_CONTEXT_H

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal.h

@@ -0,0 +1,585 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal.h
+  * @author  MCD Application Team
+  * @brief   This file contains all the functions prototypes for the HAL 
+  *          module driver.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_H
+#define __STM32F0xx_HAL_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_conf.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup HAL
+  * @{
+  */ 
+
+/* Private macros ------------------------------------------------------------*/
+/** @addtogroup HAL_Private_Macros
+  * @{
+  */
+#if defined(STM32F091xC) || defined(STM32F098xx) || defined(STM32F042x6) || defined(STM32F048xx) || \
+    defined(STM32F030x6) || defined(STM32F031x6) || defined(STM32F038xx) || defined(STM32F070x6) || \
+    defined(STM32F070xB) || defined(STM32F030x6)
+#define IS_SYSCFG_FASTMODEPLUS(__PIN__) ((((__PIN__) & SYSCFG_FASTMODEPLUS_PA9)  == SYSCFG_FASTMODEPLUS_PA9)  || \
+                                         (((__PIN__) & SYSCFG_FASTMODEPLUS_PA10) == SYSCFG_FASTMODEPLUS_PA10) || \
+                                         (((__PIN__) & SYSCFG_FASTMODEPLUS_PB6)  == SYSCFG_FASTMODEPLUS_PB6)  || \
+                                         (((__PIN__) & SYSCFG_FASTMODEPLUS_PB7)  == SYSCFG_FASTMODEPLUS_PB7)  || \
+                                         (((__PIN__) & SYSCFG_FASTMODEPLUS_PB8)  == SYSCFG_FASTMODEPLUS_PB8)  || \
+                                         (((__PIN__) & SYSCFG_FASTMODEPLUS_PB9)  == SYSCFG_FASTMODEPLUS_PB9))
+#else
+#define IS_SYSCFG_FASTMODEPLUS(__PIN__) ((((__PIN__) & SYSCFG_FASTMODEPLUS_PB6)  == SYSCFG_FASTMODEPLUS_PB6)  || \
+                                         (((__PIN__) & SYSCFG_FASTMODEPLUS_PB7)  == SYSCFG_FASTMODEPLUS_PB7)  || \
+                                         (((__PIN__) & SYSCFG_FASTMODEPLUS_PB8)  == SYSCFG_FASTMODEPLUS_PB8)  || \
+                                         (((__PIN__) & SYSCFG_FASTMODEPLUS_PB9)  == SYSCFG_FASTMODEPLUS_PB9))
+#endif
+#if defined(SYSCFG_CFGR1_PA11_PA12_RMP)
+#define IS_HAL_REMAP_PIN(RMP) ((RMP) == HAL_REMAP_PA11_PA12)
+#endif /* SYSCFG_CFGR1_PA11_PA12_RMP */
+#if defined(STM32F091xC) || defined(STM32F098xx)
+#define IS_HAL_SYSCFG_IRDA_ENV_SEL(SEL)   (((SEL) == HAL_SYSCFG_IRDA_ENV_SEL_TIM16)   || \
+                                           ((SEL) == HAL_SYSCFG_IRDA_ENV_SEL_USART1)   || \
+                                           ((SEL) == HAL_SYSCFG_IRDA_ENV_SEL_USART4))
+#endif /* STM32F091xC || STM32F098xx */
+/**
+  * @}
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup HAL_Exported_Constants HAL Exported Constants
+  * @{
+  */
+
+/** @defgroup HAL_TICK_FREQ Tick Frequency
+  * @{
+  */
+typedef enum
+{
+  HAL_TICK_FREQ_10HZ         = 100U,
+  HAL_TICK_FREQ_100HZ        = 10U,
+  HAL_TICK_FREQ_1KHZ         = 1U,
+  HAL_TICK_FREQ_DEFAULT      = HAL_TICK_FREQ_1KHZ
+} HAL_TickFreqTypeDef;
+
+/**
+  * @}
+  */
+
+#if defined(SYSCFG_CFGR1_PA11_PA12_RMP)
+/** @defgroup HAL_Pin_remapping HAL Pin remapping
+  * @{
+  */
+#define HAL_REMAP_PA11_PA12                 (SYSCFG_CFGR1_PA11_PA12_RMP)  /*!< PA11 and PA12 remapping bit for small packages (28 and 20 pins).
+                                                                           0: No remap (pin pair PA9/10 mapped on the pins)
+                                                                           1: Remap (pin pair PA11/12 mapped instead of PA9/10) */
+
+/**
+  * @}
+  */
+#endif /* SYSCFG_CFGR1_PA11_PA12_RMP */
+
+#if defined(STM32F091xC) || defined(STM32F098xx)
+/** @defgroup HAL_IRDA_ENV_SEL HAL IRDA Enveloppe Selection
+  * @note Applicable on STM32F09x
+  * @{
+  */
+#define HAL_SYSCFG_IRDA_ENV_SEL_TIM16     (SYSCFG_CFGR1_IRDA_ENV_SEL_0 & SYSCFG_CFGR1_IRDA_ENV_SEL_1)    /* 00: Timer16 is selected as IRDA Modulation enveloppe source */
+#define HAL_SYSCFG_IRDA_ENV_SEL_USART1    (SYSCFG_CFGR1_IRDA_ENV_SEL_0)  /* 01: USART1 is selected as IRDA Modulation enveloppe source */
+#define HAL_SYSCFG_IRDA_ENV_SEL_USART4    (SYSCFG_CFGR1_IRDA_ENV_SEL_1)  /* 10: USART4 is selected as IRDA Modulation enveloppe source */
+
+/**
+  * @}
+  */
+#endif /* STM32F091xC || STM32F098xx */
+
+
+/** @defgroup SYSCFG_FastModePlus_GPIO Fast-mode Plus on GPIO
+  * @{
+  */
+
+/** @brief  Fast-mode Plus driving capability on a specific GPIO
+  */  
+#if defined(STM32F091xC) || defined(STM32F098xx) || defined(STM32F042x6) || defined(STM32F048xx) || \
+    defined(STM32F030x6) || defined(STM32F031x6) || defined(STM32F038xx) || defined(STM32F070x6) || \
+    defined(STM32F070xB) || defined(STM32F030x6)
+#define SYSCFG_FASTMODEPLUS_PA9        SYSCFG_CFGR1_I2C_FMP_PA9  /*!< Enable Fast-mode Plus on PA9  */
+#define SYSCFG_FASTMODEPLUS_PA10       SYSCFG_CFGR1_I2C_FMP_PA10 /*!< Enable Fast-mode Plus on PA10 */
+#endif
+#define SYSCFG_FASTMODEPLUS_PB6        SYSCFG_CFGR1_I2C_FMP_PB6  /*!< Enable Fast-mode Plus on PB6  */
+#define SYSCFG_FASTMODEPLUS_PB7        SYSCFG_CFGR1_I2C_FMP_PB7  /*!< Enable Fast-mode Plus on PB7  */
+#define SYSCFG_FASTMODEPLUS_PB8        SYSCFG_CFGR1_I2C_FMP_PB8  /*!< Enable Fast-mode Plus on PB8  */
+#define SYSCFG_FASTMODEPLUS_PB9        SYSCFG_CFGR1_I2C_FMP_PB9  /*!< Enable Fast-mode Plus on PB9  */
+
+/**
+ * @}
+ */
+
+
+#if defined(STM32F091xC) || defined (STM32F098xx)
+/** @defgroup HAL_ISR_Wrapper HAL ISR Wrapper
+  * @brief ISR Wrapper
+  * @note applicable on STM32F09x
+  * @{
+  */
+#define HAL_SYSCFG_ITLINE0                           ( 0x00000000U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE1                           ( 0x00000001U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE2                           ( 0x00000002U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE3                           ( 0x00000003U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE4                           ( 0x00000004U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE5                           ( 0x00000005U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE6                           ( 0x00000006U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE7                           ( 0x00000007U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE8                           ( 0x00000008U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE9                           ( 0x00000009U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE10                          ( 0x0000000AU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE11                          ( 0x0000000BU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE12                          ( 0x0000000CU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE13                          ( 0x0000000DU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE14                          ( 0x0000000EU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE15                          ( 0x0000000FU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE16                          ( 0x00000010U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE17                          ( 0x00000011U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE18                          ( 0x00000012U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE19                          ( 0x00000013U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE20                          ( 0x00000014U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE21                          ( 0x00000015U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE22                          ( 0x00000016U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE23                          ( 0x00000017U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE24                          ( 0x00000018U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE25                          ( 0x00000019U) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE26                          ( 0x0000001AU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE27                          ( 0x0000001BU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE28                          ( 0x0000001CU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE29                          ( 0x0000001DU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE30                          ( 0x0000001EU) /*!< Internal define for macro handling */
+#define HAL_SYSCFG_ITLINE31                          ( 0x0000001FU) /*!< Internal define for macro handling */
+
+#define HAL_ITLINE_EWDG           ((uint32_t) ((HAL_SYSCFG_ITLINE0 << 0x18U) | SYSCFG_ITLINE0_SR_EWDG)) /*!< EWDG has expired .... */
+#if defined(STM32F091xC)
+#define HAL_ITLINE_PVDOUT         ((uint32_t) ((HAL_SYSCFG_ITLINE1 << 0x18U) | SYSCFG_ITLINE1_SR_PVDOUT)) /*!< Power voltage detection Interrupt .... */
+#endif
+#define HAL_ITLINE_VDDIO2         ((uint32_t) ((HAL_SYSCFG_ITLINE1 << 0x18U) | SYSCFG_ITLINE1_SR_VDDIO2)) /*!< VDDIO2 Interrupt .... */
+#define HAL_ITLINE_RTC_WAKEUP     ((uint32_t) ((HAL_SYSCFG_ITLINE2 << 0x18U) | SYSCFG_ITLINE2_SR_RTC_WAKEUP)) /*!< RTC WAKEUP -> exti[20] Interrupt */
+#define HAL_ITLINE_RTC_TSTAMP     ((uint32_t) ((HAL_SYSCFG_ITLINE2 << 0x18U) | SYSCFG_ITLINE2_SR_RTC_TSTAMP)) /*!< RTC Time Stamp -> exti[19] interrupt */
+#define HAL_ITLINE_RTC_ALRA       ((uint32_t) ((HAL_SYSCFG_ITLINE2 << 0x18U) | SYSCFG_ITLINE2_SR_RTC_ALRA)) /*!< RTC Alarm -> exti[17] interrupt .... */
+#define HAL_ITLINE_FLASH_ITF      ((uint32_t) ((HAL_SYSCFG_ITLINE3 << 0x18U) | SYSCFG_ITLINE3_SR_FLASH_ITF)) /*!< Flash ITF Interrupt */
+#define HAL_ITLINE_CRS            ((uint32_t) ((HAL_SYSCFG_ITLINE4 << 0x18U) | SYSCFG_ITLINE4_SR_CRS)) /*!< CRS Interrupt */
+#define HAL_ITLINE_CLK_CTRL       ((uint32_t) ((HAL_SYSCFG_ITLINE4 << 0x18U) | SYSCFG_ITLINE4_SR_CLK_CTRL)) /*!< CLK Control Interrupt */
+#define HAL_ITLINE_EXTI0          ((uint32_t) ((HAL_SYSCFG_ITLINE5 << 0x18U) | SYSCFG_ITLINE5_SR_EXTI0)) /*!< External Interrupt 0 */
+#define HAL_ITLINE_EXTI1          ((uint32_t) ((HAL_SYSCFG_ITLINE5 << 0x18U) | SYSCFG_ITLINE5_SR_EXTI1)) /*!< External Interrupt 1 */
+#define HAL_ITLINE_EXTI2          ((uint32_t) ((HAL_SYSCFG_ITLINE6 << 0x18U) | SYSCFG_ITLINE6_SR_EXTI2)) /*!< External Interrupt 2 */
+#define HAL_ITLINE_EXTI3          ((uint32_t) ((HAL_SYSCFG_ITLINE6 << 0x18U) | SYSCFG_ITLINE6_SR_EXTI3)) /*!< External Interrupt 3 */
+#define HAL_ITLINE_EXTI4          ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI4)) /*!< EXTI4 Interrupt */
+#define HAL_ITLINE_EXTI5          ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI5)) /*!< EXTI5 Interrupt */
+#define HAL_ITLINE_EXTI6          ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI6)) /*!< EXTI6 Interrupt */
+#define HAL_ITLINE_EXTI7          ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI7)) /*!< EXTI7 Interrupt */
+#define HAL_ITLINE_EXTI8          ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI8)) /*!< EXTI8 Interrupt */
+#define HAL_ITLINE_EXTI9          ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI9)) /*!< EXTI9 Interrupt */
+#define HAL_ITLINE_EXTI10         ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI10)) /*!< EXTI10 Interrupt */
+#define HAL_ITLINE_EXTI11         ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI11)) /*!< EXTI11 Interrupt */
+#define HAL_ITLINE_EXTI12         ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI12)) /*!< EXTI12 Interrupt */
+#define HAL_ITLINE_EXTI13         ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI13)) /*!< EXTI13 Interrupt */
+#define HAL_ITLINE_EXTI14         ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI14)) /*!< EXTI14 Interrupt */
+#define HAL_ITLINE_EXTI15         ((uint32_t) ((HAL_SYSCFG_ITLINE7 << 0x18U) | SYSCFG_ITLINE7_SR_EXTI15)) /*!< EXTI15 Interrupt */
+#define HAL_ITLINE_TSC_EOA        ((uint32_t) ((HAL_SYSCFG_ITLINE8 << 0x18U) | SYSCFG_ITLINE8_SR_TSC_EOA)) /*!< Touch control EOA Interrupt */
+#define HAL_ITLINE_TSC_MCE        ((uint32_t) ((HAL_SYSCFG_ITLINE8 << 0x18U) | SYSCFG_ITLINE8_SR_TSC_MCE)) /*!< Touch control MCE Interrupt */
+#define HAL_ITLINE_DMA1_CH1       ((uint32_t) ((HAL_SYSCFG_ITLINE9 << 0x18U) | SYSCFG_ITLINE9_SR_DMA1_CH1)) /*!< DMA1 Channel 1 Interrupt */
+#define HAL_ITLINE_DMA1_CH2       ((uint32_t) ((HAL_SYSCFG_ITLINE10 << 0x18U) | SYSCFG_ITLINE10_SR_DMA1_CH2)) /*!< DMA1 Channel 2 Interrupt */
+#define HAL_ITLINE_DMA1_CH3       ((uint32_t) ((HAL_SYSCFG_ITLINE10 << 0x18U) | SYSCFG_ITLINE10_SR_DMA1_CH3)) /*!< DMA1 Channel 3 Interrupt */
+#define HAL_ITLINE_DMA2_CH1       ((uint32_t) ((HAL_SYSCFG_ITLINE10 << 0x18U) | SYSCFG_ITLINE10_SR_DMA2_CH1)) /*!< DMA2 Channel 1 Interrupt */
+#define HAL_ITLINE_DMA2_CH2       ((uint32_t) ((HAL_SYSCFG_ITLINE10 << 0x18U) | SYSCFG_ITLINE10_SR_DMA2_CH2)) /*!< DMA2 Channel 2 Interrupt */
+#define HAL_ITLINE_DMA1_CH4       ((uint32_t) ((HAL_SYSCFG_ITLINE11 << 0x18U) | SYSCFG_ITLINE11_SR_DMA1_CH4)) /*!< DMA1 Channel 4 Interrupt */
+#define HAL_ITLINE_DMA1_CH5       ((uint32_t) ((HAL_SYSCFG_ITLINE11 << 0x18U) | SYSCFG_ITLINE11_SR_DMA1_CH5)) /*!< DMA1 Channel 5 Interrupt */
+#define HAL_ITLINE_DMA1_CH6       ((uint32_t) ((HAL_SYSCFG_ITLINE11 << 0x18U) | SYSCFG_ITLINE11_SR_DMA1_CH6)) /*!< DMA1 Channel 6 Interrupt */
+#define HAL_ITLINE_DMA1_CH7       ((uint32_t) ((HAL_SYSCFG_ITLINE11 << 0x18U) | SYSCFG_ITLINE11_SR_DMA1_CH7)) /*!< DMA1 Channel 7 Interrupt */
+#define HAL_ITLINE_DMA2_CH3       ((uint32_t) ((HAL_SYSCFG_ITLINE11 << 0x18U) | SYSCFG_ITLINE11_SR_DMA2_CH3)) /*!< DMA2 Channel 3 Interrupt */
+#define HAL_ITLINE_DMA2_CH4       ((uint32_t) ((HAL_SYSCFG_ITLINE11 << 0x18U) | SYSCFG_ITLINE11_SR_DMA2_CH4)) /*!< DMA2 Channel 4 Interrupt */
+#define HAL_ITLINE_DMA2_CH5       ((uint32_t) ((HAL_SYSCFG_ITLINE11 << 0x18U) | SYSCFG_ITLINE11_SR_DMA2_CH5)) /*!< DMA2 Channel 5 Interrupt */
+#define HAL_ITLINE_ADC            ((uint32_t) ((HAL_SYSCFG_ITLINE12 << 0x18U) | SYSCFG_ITLINE12_SR_ADC)) /*!< ADC Interrupt */
+#define HAL_ITLINE_COMP1          ((uint32_t) ((HAL_SYSCFG_ITLINE12 << 0x18U) | SYSCFG_ITLINE12_SR_COMP1)) /*!< COMP1 Interrupt -> exti[21] */
+#define HAL_ITLINE_COMP2          ((uint32_t) ((HAL_SYSCFG_ITLINE12 << 0x18U) | SYSCFG_ITLINE12_SR_COMP2)) /*!< COMP2 Interrupt -> exti[21] */
+#define HAL_ITLINE_TIM1_BRK       ((uint32_t) ((HAL_SYSCFG_ITLINE13 << 0x18U) | SYSCFG_ITLINE13_SR_TIM1_BRK)) /*!< TIM1 BRK Interrupt */
+#define HAL_ITLINE_TIM1_UPD       ((uint32_t) ((HAL_SYSCFG_ITLINE13 << 0x18U) | SYSCFG_ITLINE13_SR_TIM1_UPD)) /*!< TIM1 UPD Interrupt */
+#define HAL_ITLINE_TIM1_TRG       ((uint32_t) ((HAL_SYSCFG_ITLINE13 << 0x18U) | SYSCFG_ITLINE13_SR_TIM1_TRG)) /*!< TIM1 TRG Interrupt */
+#define HAL_ITLINE_TIM1_CCU       ((uint32_t) ((HAL_SYSCFG_ITLINE13 << 0x18U) | SYSCFG_ITLINE13_SR_TIM1_CCU)) /*!< TIM1 CCU Interrupt */
+#define HAL_ITLINE_TIM1_CC        ((uint32_t) ((HAL_SYSCFG_ITLINE14 << 0x18U) | SYSCFG_ITLINE14_SR_TIM1_CC)) /*!< TIM1 CC Interrupt */
+#define HAL_ITLINE_TIM2           ((uint32_t) ((HAL_SYSCFG_ITLINE15 << 0x18U) | SYSCFG_ITLINE15_SR_TIM2_GLB)) /*!< TIM2 Interrupt */
+#define HAL_ITLINE_TIM3           ((uint32_t) ((HAL_SYSCFG_ITLINE16 << 0x18U) | SYSCFG_ITLINE16_SR_TIM3_GLB)) /*!< TIM3 Interrupt */
+#define HAL_ITLINE_DAC            ((uint32_t) ((HAL_SYSCFG_ITLINE17 << 0x18U) | SYSCFG_ITLINE17_SR_DAC)) /*!< DAC Interrupt */
+#define HAL_ITLINE_TIM6           ((uint32_t) ((HAL_SYSCFG_ITLINE17 << 0x18U) | SYSCFG_ITLINE17_SR_TIM6_GLB)) /*!< TIM6 Interrupt */
+#define HAL_ITLINE_TIM7           ((uint32_t) ((HAL_SYSCFG_ITLINE18 << 0x18U) | SYSCFG_ITLINE18_SR_TIM7_GLB)) /*!< TIM7 Interrupt */
+#define HAL_ITLINE_TIM14          ((uint32_t) ((HAL_SYSCFG_ITLINE19 << 0x18U) | SYSCFG_ITLINE19_SR_TIM14_GLB)) /*!< TIM14 Interrupt */
+#define HAL_ITLINE_TIM15          ((uint32_t) ((HAL_SYSCFG_ITLINE20 << 0x18U) | SYSCFG_ITLINE20_SR_TIM15_GLB)) /*!< TIM15 Interrupt */
+#define HAL_ITLINE_TIM16          ((uint32_t) ((HAL_SYSCFG_ITLINE21 << 0x18U) | SYSCFG_ITLINE21_SR_TIM16_GLB)) /*!< TIM16 Interrupt */
+#define HAL_ITLINE_TIM17          ((uint32_t) ((HAL_SYSCFG_ITLINE22 << 0x18U) | SYSCFG_ITLINE22_SR_TIM17_GLB)) /*!< TIM17 Interrupt */
+#define HAL_ITLINE_I2C1           ((uint32_t) ((HAL_SYSCFG_ITLINE23 << 0x18U) | SYSCFG_ITLINE23_SR_I2C1_GLB)) /*!< I2C1 Interrupt -> exti[23] */
+#define HAL_ITLINE_I2C2           ((uint32_t) ((HAL_SYSCFG_ITLINE24 << 0x18U) | SYSCFG_ITLINE24_SR_I2C2_GLB)) /*!< I2C2 Interrupt */
+#define HAL_ITLINE_SPI1           ((uint32_t) ((HAL_SYSCFG_ITLINE25 << 0x18U) | SYSCFG_ITLINE25_SR_SPI1)) /*!< I2C1 Interrupt -> exti[23] */
+#define HAL_ITLINE_SPI2           ((uint32_t) ((HAL_SYSCFG_ITLINE26 << 0x18U) | SYSCFG_ITLINE26_SR_SPI2)) /*!< SPI1 Interrupt */
+#define HAL_ITLINE_USART1         ((uint32_t) ((HAL_SYSCFG_ITLINE27 << 0x18U) | SYSCFG_ITLINE27_SR_USART1_GLB)) /*!< USART1 GLB Interrupt -> exti[25] */
+#define HAL_ITLINE_USART2         ((uint32_t) ((HAL_SYSCFG_ITLINE28 << 0x18U) | SYSCFG_ITLINE28_SR_USART2_GLB)) /*!< USART2 GLB Interrupt -> exti[26] */
+#define HAL_ITLINE_USART3         ((uint32_t) ((HAL_SYSCFG_ITLINE29 << 0x18U) | SYSCFG_ITLINE29_SR_USART3_GLB)) /*!< USART3 Interrupt .... */
+#define HAL_ITLINE_USART4         ((uint32_t) ((HAL_SYSCFG_ITLINE29 << 0x18U) | SYSCFG_ITLINE29_SR_USART4_GLB)) /*!< USART4 Interrupt .... */
+#define HAL_ITLINE_USART5         ((uint32_t) ((HAL_SYSCFG_ITLINE29 << 0x18U) | SYSCFG_ITLINE29_SR_USART5_GLB)) /*!< USART5 Interrupt .... */
+#define HAL_ITLINE_USART6         ((uint32_t) ((HAL_SYSCFG_ITLINE29 << 0x18U) | SYSCFG_ITLINE29_SR_USART6_GLB)) /*!< USART6 Interrupt .... */
+#define HAL_ITLINE_USART7         ((uint32_t) ((HAL_SYSCFG_ITLINE29 << 0x18U) | SYSCFG_ITLINE29_SR_USART7_GLB)) /*!< USART7 Interrupt .... */
+#define HAL_ITLINE_USART8         ((uint32_t) ((HAL_SYSCFG_ITLINE29 << 0x18U) | SYSCFG_ITLINE29_SR_USART8_GLB)) /*!< USART8 Interrupt .... */
+#define HAL_ITLINE_CAN            ((uint32_t) ((HAL_SYSCFG_ITLINE30 << 0x18U) | SYSCFG_ITLINE30_SR_CAN)) /*!< CAN Interrupt */
+#define HAL_ITLINE_CEC            ((uint32_t) ((HAL_SYSCFG_ITLINE30 << 0x18U) | SYSCFG_ITLINE30_SR_CEC)) /*!< CEC Interrupt -> exti[27] */
+/**
+  * @}
+  */
+#endif /* STM32F091xC || STM32F098xx */
+
+/**
+  * @}
+  */  
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup HAL_Exported_Macros HAL Exported Macros
+  * @{  
+  */
+
+/** @defgroup HAL_Freeze_Unfreeze_Peripherals HAL Freeze Unfreeze Peripherals
+  * @brief  Freeze/Unfreeze Peripherals in Debug mode 
+  * @{  
+  */
+  
+#if defined(DBGMCU_APB1_FZ_DBG_CAN_STOP)
+#define __HAL_FREEZE_CAN_DBGMCU()            (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_CAN_STOP))
+#define __HAL_UNFREEZE_CAN_DBGMCU()          (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_CAN_STOP))
+#endif /* DBGMCU_APB1_FZ_DBG_CAN_STOP */
+
+#if defined(DBGMCU_APB1_FZ_DBG_RTC_STOP)
+#define __HAL_DBGMCU_FREEZE_RTC()            (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_RTC_STOP))
+#define __HAL_DBGMCU_UNFREEZE_RTC()          (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_RTC_STOP))
+#endif /* DBGMCU_APB1_FZ_DBG_RTC_STOP */
+
+#if defined(DBGMCU_APB1_FZ_DBG_I2C1_SMBUS_TIMEOUT)
+#define __HAL_DBGMCU_FREEZE_I2C1_TIMEOUT()   (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_I2C1_SMBUS_TIMEOUT))
+#define __HAL_DBGMCU_UNFREEZE_I2C1_TIMEOUT() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_I2C1_SMBUS_TIMEOUT))
+#endif /* DBGMCU_APB1_FZ_DBG_I2C1_SMBUS_TIMEOUT */
+
+#if defined(DBGMCU_APB1_FZ_DBG_IWDG_STOP)
+#define __HAL_DBGMCU_FREEZE_IWDG()           (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_IWDG_STOP))
+#define __HAL_DBGMCU_UNFREEZE_IWDG()         (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_IWDG_STOP))
+#endif /* DBGMCU_APB1_FZ_DBG_IWDG_STOP */
+
+#if defined(DBGMCU_APB1_FZ_DBG_WWDG_STOP)
+#define __HAL_DBGMCU_FREEZE_WWDG()           (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_WWDG_STOP))
+#define __HAL_DBGMCU_UNFREEZE_WWDG()         (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_WWDG_STOP))
+#endif /* DBGMCU_APB1_FZ_DBG_WWDG_STOP */
+
+#if defined(DBGMCU_APB1_FZ_DBG_TIM2_STOP)
+#define __HAL_DBGMCU_FREEZE_TIM2()           (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM2_STOP))
+#define __HAL_DBGMCU_UNFREEZE_TIM2()         (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM2_STOP))
+#endif /* DBGMCU_APB1_FZ_DBG_TIM2_STOP */
+
+#if defined(DBGMCU_APB1_FZ_DBG_TIM3_STOP)
+#define __HAL_DBGMCU_FREEZE_TIM3()           (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM3_STOP))
+#define __HAL_DBGMCU_UNFREEZE_TIM3()         (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM3_STOP))
+#endif /* DBGMCU_APB1_FZ_DBG_TIM3_STOP */
+
+#if defined(DBGMCU_APB1_FZ_DBG_TIM6_STOP)
+#define __HAL_DBGMCU_FREEZE_TIM6()           (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM6_STOP))
+#define __HAL_DBGMCU_UNFREEZE_TIM6()         (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM6_STOP))
+#endif /* DBGMCU_APB1_FZ_DBG_TIM6_STOP */
+
+#if defined(DBGMCU_APB1_FZ_DBG_TIM7_STOP)
+#define __HAL_DBGMCU_FREEZE_TIM7()           (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM7_STOP))
+#define __HAL_DBGMCU_UNFREEZE_TIM7()         (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM7_STOP))
+#endif /* DBGMCU_APB1_FZ_DBG_TIM7_STOP */
+
+#if defined(DBGMCU_APB1_FZ_DBG_TIM14_STOP)
+#define __HAL_DBGMCU_FREEZE_TIM14()          (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM14_STOP))
+#define __HAL_DBGMCU_UNFREEZE_TIM14()        (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM14_STOP))
+#endif /* DBGMCU_APB1_FZ_DBG_TIM14_STOP */
+
+#if defined(DBGMCU_APB2_FZ_DBG_TIM1_STOP)
+#define __HAL_DBGMCU_FREEZE_TIM1()           (DBGMCU->APB2FZ |= (DBGMCU_APB2_FZ_DBG_TIM1_STOP))
+#define __HAL_DBGMCU_UNFREEZE_TIM1()         (DBGMCU->APB2FZ &= ~(DBGMCU_APB2_FZ_DBG_TIM1_STOP))
+#endif /* DBGMCU_APB2_FZ_DBG_TIM1_STOP */
+
+#if defined(DBGMCU_APB2_FZ_DBG_TIM15_STOP)
+#define __HAL_DBGMCU_FREEZE_TIM15()          (DBGMCU->APB2FZ |= (DBGMCU_APB2_FZ_DBG_TIM15_STOP))
+#define __HAL_DBGMCU_UNFREEZE_TIM15()        (DBGMCU->APB2FZ &= ~(DBGMCU_APB2_FZ_DBG_TIM15_STOP))
+#endif /* DBGMCU_APB2_FZ_DBG_TIM15_STOP */
+
+#if defined(DBGMCU_APB2_FZ_DBG_TIM16_STOP)
+#define __HAL_DBGMCU_FREEZE_TIM16()          (DBGMCU->APB2FZ |= (DBGMCU_APB2_FZ_DBG_TIM16_STOP))
+#define __HAL_DBGMCU_UNFREEZE_TIM16()        (DBGMCU->APB2FZ &= ~(DBGMCU_APB2_FZ_DBG_TIM16_STOP))
+#endif /* DBGMCU_APB2_FZ_DBG_TIM16_STOP */
+
+#if defined(DBGMCU_APB2_FZ_DBG_TIM17_STOP)
+#define __HAL_DBGMCU_FREEZE_TIM17()          (DBGMCU->APB2FZ |= (DBGMCU_APB2_FZ_DBG_TIM17_STOP))
+#define __HAL_DBGMCU_UNFREEZE_TIM17()        (DBGMCU->APB2FZ &= ~(DBGMCU_APB2_FZ_DBG_TIM17_STOP))
+#endif /* DBGMCU_APB2_FZ_DBG_TIM17_STOP */
+
+/**
+  * @}
+  */  
+  
+/** @defgroup Memory_Mapping_Selection Memory Mapping Selection
+  * @{   
+  */
+#if defined(SYSCFG_CFGR1_MEM_MODE)
+/** @brief  Main Flash memory mapped at 0x00000000
+  */
+#define __HAL_SYSCFG_REMAPMEMORY_FLASH()        (SYSCFG->CFGR1 &= ~(SYSCFG_CFGR1_MEM_MODE))
+#endif /* SYSCFG_CFGR1_MEM_MODE */
+
+#if defined(SYSCFG_CFGR1_MEM_MODE_0)
+/** @brief  System Flash memory mapped at 0x00000000
+  */
+#define __HAL_SYSCFG_REMAPMEMORY_SYSTEMFLASH()  do {SYSCFG->CFGR1 &= ~(SYSCFG_CFGR1_MEM_MODE); \
+                                             SYSCFG->CFGR1 |= SYSCFG_CFGR1_MEM_MODE_0;  \
+                                            }while(0)
+#endif /* SYSCFG_CFGR1_MEM_MODE_0 */
+
+#if defined(SYSCFG_CFGR1_MEM_MODE_0) && defined(SYSCFG_CFGR1_MEM_MODE_1)
+/** @brief  Embedded SRAM mapped at 0x00000000
+  */
+#define __HAL_SYSCFG_REMAPMEMORY_SRAM()         do {SYSCFG->CFGR1 &= ~(SYSCFG_CFGR1_MEM_MODE); \
+                                             SYSCFG->CFGR1 |= (SYSCFG_CFGR1_MEM_MODE_0 | SYSCFG_CFGR1_MEM_MODE_1); \
+                                            }while(0) 
+#endif /* SYSCFG_CFGR1_MEM_MODE_0 && SYSCFG_CFGR1_MEM_MODE_1 */
+/**
+  * @}
+  */ 
+
+
+#if defined(SYSCFG_CFGR1_PA11_PA12_RMP)
+/** @defgroup HAL_Pin_remap HAL Pin remap 
+  * @brief  Pin remapping enable/disable macros
+  * @param __PIN_REMAP__ This parameter can be a value of @ref HAL_Pin_remapping
+  * @{   
+  */
+#define __HAL_REMAP_PIN_ENABLE(__PIN_REMAP__)          do {assert_param(IS_HAL_REMAP_PIN((__PIN_REMAP__)));                 \
+                                                           SYSCFG->CFGR1 |= (__PIN_REMAP__);                                \
+                                                         }while(0)
+#define __HAL_REMAP_PIN_DISABLE(__PIN_REMAP__)         do {assert_param(IS_HAL_REMAP_PIN((__PIN_REMAP__)));                 \
+                                                           SYSCFG->CFGR1 &= ~(__PIN_REMAP__);                               \
+                                                         }while(0)
+/**
+  * @}
+  */  
+#endif /* SYSCFG_CFGR1_PA11_PA12_RMP */
+
+/** @brief  Fast-mode Plus driving capability enable/disable macros
+  * @param __FASTMODEPLUS__ This parameter can be a value of @ref SYSCFG_FastModePlus_GPIO values.
+  *                          That you can find above these macros.
+  */
+#define __HAL_SYSCFG_FASTMODEPLUS_ENABLE(__FASTMODEPLUS__)  do {assert_param(IS_SYSCFG_FASTMODEPLUS((__FASTMODEPLUS__)));\
+                                                                SET_BIT(SYSCFG->CFGR1, (__FASTMODEPLUS__));\
+                                                               }while(0)
+
+#define __HAL_SYSCFG_FASTMODEPLUS_DISABLE(__FASTMODEPLUS__) do {assert_param(IS_SYSCFG_FASTMODEPLUS((__FASTMODEPLUS__)));\
+                                                                CLEAR_BIT(SYSCFG->CFGR1, (__FASTMODEPLUS__));\
+                                                               }while(0)
+#if defined(SYSCFG_CFGR2_LOCKUP_LOCK)
+/** @defgroup Cortex_Lockup_Enable Cortex Lockup Enable
+  * @{   
+  */
+/** @brief  SYSCFG Break Lockup lock
+  *         Enables and locks the connection of Cortex-M0 LOCKUP (Hardfault) output to TIM1/15/16/17 Break input
+  * @note   The selected configuration is locked and can be unlocked by system reset
+  */
+#define __HAL_SYSCFG_BREAK_LOCKUP_LOCK()   do {SYSCFG->CFGR2 &= ~(SYSCFG_CFGR2_LOCKUP_LOCK); \
+                                               SYSCFG->CFGR2 |= SYSCFG_CFGR2_LOCKUP_LOCK;    \
+                                              }while(0)
+/**
+  * @}
+  */  
+#endif /* SYSCFG_CFGR2_LOCKUP_LOCK */
+
+#if defined(SYSCFG_CFGR2_PVD_LOCK)
+/** @defgroup PVD_Lock_Enable PVD Lock
+  * @{  
+  */
+/** @brief  SYSCFG Break PVD lock
+  *         Enables and locks the PVD connection with Timer1/8/15/16/17 Break Input, , as well as the PVDE and PLS[2:0] in the PWR_CR register
+  * @note   The selected configuration is locked and can be unlocked by system reset
+  */
+#define __HAL_SYSCFG_BREAK_PVD_LOCK()      do {SYSCFG->CFGR2 &= ~(SYSCFG_CFGR2_PVD_LOCK); \
+                                               SYSCFG->CFGR2 |= SYSCFG_CFGR2_PVD_LOCK;    \
+                                              }while(0)
+/**
+  * @}
+  */
+#endif /* SYSCFG_CFGR2_PVD_LOCK */
+
+#if defined(SYSCFG_CFGR2_SRAM_PARITY_LOCK)
+/** @defgroup SRAM_Parity_Lock SRAM Parity Lock
+  * @{
+  */
+/** @brief  SYSCFG Break SRAM PARITY lock
+  *         Enables and locks the SRAM_PARITY error signal with Break Input of TIMER1/8/15/16/17
+  * @note   The selected configuration is locked and can be unlocked by system reset
+  */
+#define __HAL_SYSCFG_BREAK_SRAMPARITY_LOCK() do {SYSCFG->CFGR2 &= ~(SYSCFG_CFGR2_SRAM_PARITY_LOCK); \
+                                                 SYSCFG->CFGR2 |= SYSCFG_CFGR2_SRAM_PARITY_LOCK;    \
+                                                }while(0)
+/**
+  * @}
+  */
+#endif /* SYSCFG_CFGR2_SRAM_PARITY_LOCK */
+
+#if defined(SYSCFG_CFGR2_SRAM_PEF)
+/** @defgroup HAL_SYSCFG_Parity_check_on_RAM HAL SYSCFG Parity check on RAM
+  * @brief  Parity check on RAM disable macro
+  * @note   Disabling the parity check on RAM locks the configuration bit.
+  *         To re-enable the parity check on RAM perform a system reset.
+  * @{  
+  */
+#define __HAL_SYSCFG_RAM_PARITYCHECK_DISABLE()   (SYSCFG->CFGR2 |= SYSCFG_CFGR2_SRAM_PEF)
+/**
+  * @}
+  */
+#endif /* SYSCFG_CFGR2_SRAM_PEF */
+
+
+#if defined(STM32F091xC) || defined (STM32F098xx)
+/** @defgroup HAL_ISR_wrapper_check HAL ISR wrapper check
+  * @brief  ISR wrapper check
+  * @note This feature is applicable on STM32F09x  
+  * @note Allow to determine interrupt source per line.
+  * @{  
+  */
+#define __HAL_GET_PENDING_IT(__SOURCE__)       (SYSCFG->IT_LINE_SR[((__SOURCE__) >> 0x18U)] & ((__SOURCE__) & 0x00FFFFFF))
+/**
+  * @}
+  */
+#endif /* (STM32F091xC) || defined (STM32F098xx)*/
+
+#if defined(STM32F091xC) || defined (STM32F098xx)
+/** @defgroup HAL_SYSCFG_IRDA_modulation_envelope_selection HAL SYSCFG IRDA modulation envelope selection
+  * @brief  selection of the modulation envelope signal macro, using bits [7:6] of SYS_CTRL(CFGR1) register
+  * @note This feature is applicable on STM32F09x
+  * @param __SOURCE__ This parameter can be a value of @ref HAL_IRDA_ENV_SEL
+  * @{  
+  */
+#define __HAL_SYSCFG_IRDA_ENV_SELECTION(__SOURCE__)  do {assert_param(IS_HAL_SYSCFG_IRDA_ENV_SEL((__SOURCE__))); \
+                                                         SYSCFG->CFGR1 &= ~(SYSCFG_CFGR1_IRDA_ENV_SEL); \
+                                                         SYSCFG->CFGR1 |= (__SOURCE__);    \
+                                                        }while(0)
+
+#define __HAL_SYSCFG_GET_IRDA_ENV_SELECTION()  ((SYSCFG->CFGR1) & 0x000000C0)
+/**
+  * @}
+  */
+#endif /* (STM32F091xC) || defined (STM32F098xx)*/
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_Private_Macros HAL Private Macros
+  * @{
+  */
+#define IS_TICKFREQ(FREQ) (((FREQ) == HAL_TICK_FREQ_10HZ)  || \
+                           ((FREQ) == HAL_TICK_FREQ_100HZ) || \
+                           ((FREQ) == HAL_TICK_FREQ_1KHZ))
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup HAL_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup HAL_Exported_Functions_Group1
+  * @{
+  */    
+/* Initialization and de-initialization functions  ******************************/
+HAL_StatusTypeDef HAL_Init(void);
+HAL_StatusTypeDef HAL_DeInit(void);
+void              HAL_MspInit(void);
+void              HAL_MspDeInit(void);
+HAL_StatusTypeDef HAL_InitTick (uint32_t TickPriority);
+/**
+  * @}
+  */
+
+/* Exported variables ---------------------------------------------------------*/
+/** @addtogroup HAL_Exported_Variables
+  * @{
+  */
+extern __IO uint32_t uwTick;
+extern uint32_t uwTickPrio;
+extern HAL_TickFreqTypeDef uwTickFreq;
+/**
+  * @}
+  */
+
+/** @addtogroup HAL_Exported_Functions_Group2
+  * @{
+  */    
+
+/* Peripheral Control functions  ************************************************/
+void                HAL_IncTick(void);
+void                HAL_Delay(uint32_t Delay);
+uint32_t            HAL_GetTick(void);
+uint32_t            HAL_GetTickPrio(void);
+HAL_StatusTypeDef   HAL_SetTickFreq(HAL_TickFreqTypeDef Freq);
+HAL_TickFreqTypeDef HAL_GetTickFreq(void);
+void                HAL_SuspendTick(void);
+void                HAL_ResumeTick(void);
+uint32_t            HAL_GetHalVersion(void);
+uint32_t            HAL_GetREVID(void);
+uint32_t            HAL_GetDEVID(void);
+uint32_t            HAL_GetUIDw0(void);
+uint32_t            HAL_GetUIDw1(void);
+uint32_t            HAL_GetUIDw2(void);
+void                HAL_DBGMCU_EnableDBGStopMode(void);
+void                HAL_DBGMCU_DisableDBGStopMode(void);
+void                HAL_DBGMCU_EnableDBGStandbyMode(void);
+void                HAL_DBGMCU_DisableDBGStandbyMode(void);
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_cortex.h

@@ -0,0 +1,133 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_cortex.h
+  * @author  MCD Application Team
+  * @brief   Header file of CORTEX HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_CORTEX_H
+#define __STM32F0xx_HAL_CORTEX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup CORTEX CORTEX
+  * @{
+  */ 
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup CORTEX_Exported_Constants CORTEX Exported Constants
+  * @{
+  */
+  
+/** @defgroup CORTEX_SysTick_clock_source CORTEX SysTick clock source
+  * @{
+  */
+#define SYSTICK_CLKSOURCE_HCLK_DIV8    (0x00000000U)
+#define SYSTICK_CLKSOURCE_HCLK         (0x00000004U)
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+/* Exported Macros -----------------------------------------------------------*/
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup CORTEX_Exported_Functions CORTEX Exported Functions
+  * @{
+  */
+/** @addtogroup CORTEX_Exported_Functions_Group1 Initialization and de-initialization functions 
+ *  @brief    Initialization and Configuration functions
+ * @{
+ */
+/* Initialization and de-initialization functions *******************************/
+void HAL_NVIC_SetPriority(IRQn_Type IRQn,uint32_t PreemptPriority, uint32_t SubPriority);
+void HAL_NVIC_EnableIRQ(IRQn_Type IRQn);
+void HAL_NVIC_DisableIRQ(IRQn_Type IRQn);
+void HAL_NVIC_SystemReset(void);
+uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb);
+/**
+  * @}
+  */
+
+/** @addtogroup CORTEX_Exported_Functions_Group2 Peripheral Control functions 
+ *  @brief   Cortex control functions
+ * @{
+ */
+ 
+/* Peripheral Control functions *************************************************/
+uint32_t HAL_NVIC_GetPriority(IRQn_Type IRQn);
+uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn);
+void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn);
+void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn);
+void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource);
+void HAL_SYSTICK_IRQHandler(void);
+void HAL_SYSTICK_Callback(void);
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+/* Private types -------------------------------------------------------------*/ 
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup CORTEX_Private_Macros CORTEX Private Macros
+  * @{
+  */
+#define IS_NVIC_PREEMPTION_PRIORITY(PRIORITY)  ((PRIORITY) < 0x4)
+
+#define IS_NVIC_DEVICE_IRQ(IRQ)                ((IRQ) >= 0x00)
+
+#define IS_SYSTICK_CLK_SOURCE(SOURCE) (((SOURCE) == SYSTICK_CLKSOURCE_HCLK) || \
+                                      ((SOURCE) == SYSTICK_CLKSOURCE_HCLK_DIV8))
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+    
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_CORTEX_H */
+ 
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_def.h

@@ -0,0 +1,178 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_def.h
+  * @author  MCD Application Team
+  * @brief   This file contains HAL common defines, enumeration, macros and 
+  *          structures definitions. 
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_DEF
+#define __STM32F0xx_HAL_DEF
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx.h"
+#include "Legacy/stm32_hal_legacy.h"
+#include <stddef.h>
+
+/* Exported types ------------------------------------------------------------*/
+
+/** 
+  * @brief  HAL Status structures definition  
+  */  
+typedef enum 
+{
+  HAL_OK       = 0x00U,
+  HAL_ERROR    = 0x01U,
+  HAL_BUSY     = 0x02U,
+  HAL_TIMEOUT  = 0x03U
+} HAL_StatusTypeDef;
+
+/** 
+  * @brief  HAL Lock structures definition  
+  */
+typedef enum 
+{
+  HAL_UNLOCKED = 0x00U,
+  HAL_LOCKED   = 0x01U  
+} HAL_LockTypeDef;
+
+/* Exported macro ------------------------------------------------------------*/
+
+#define UNUSED(X) (void)X      /* To avoid gcc/g++ warnings */
+
+#define HAL_MAX_DELAY      0xFFFFFFFFU
+
+#define HAL_IS_BIT_SET(REG, BIT)         (((REG) & (BIT)) == (BIT))
+#define HAL_IS_BIT_CLR(REG, BIT)         (((REG) & (BIT)) == 0U)
+
+#define __HAL_LINKDMA(__HANDLE__, __PPP_DMA_FIELD__, __DMA_HANDLE__)               \
+                        do{                                                        \
+                              (__HANDLE__)->__PPP_DMA_FIELD__ = &(__DMA_HANDLE__); \
+                              (__DMA_HANDLE__).Parent = (__HANDLE__);             \
+                          } while(0U)
+
+/** @brief Reset the Handle's State field.
+  * @param __HANDLE__ specifies the Peripheral Handle.
+  * @note  This macro can be used for the following purpose:
+  *          - When the Handle is declared as local variable; before passing it as parameter
+  *            to HAL_PPP_Init() for the first time, it is mandatory to use this macro
+  *            to set to 0 the Handle's "State" field.
+  *            Otherwise, "State" field may have any random value and the first time the function
+  *            HAL_PPP_Init() is called, the low level hardware initialization will be missed
+  *            (i.e. HAL_PPP_MspInit() will not be executed).
+  *          - When there is a need to reconfigure the low level hardware: instead of calling
+  *            HAL_PPP_DeInit() then HAL_PPP_Init(), user can make a call to this macro then HAL_PPP_Init().
+  *            In this later function, when the Handle's "State" field is set to 0, it will execute the function
+  *            HAL_PPP_MspInit() which will reconfigure the low level hardware.
+  * @retval None
+  */
+#define __HAL_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = 0U)
+
+#if (USE_RTOS == 1U)
+  /* Reserved for future use */
+  #error " USE_RTOS should be 0 in the current HAL release "
+#else
+  #define __HAL_LOCK(__HANDLE__)                                           \
+                                do{                                        \
+                                    if((__HANDLE__)->Lock == HAL_LOCKED)   \
+                                    {                                      \
+                                       return HAL_BUSY;                    \
+                                    }                                      \
+                                    else                                   \
+                                    {                                      \
+                                       (__HANDLE__)->Lock = HAL_LOCKED;    \
+                                    }                                      \
+                                  }while (0U)
+
+  #define __HAL_UNLOCK(__HANDLE__)                                          \
+                                  do{                                       \
+                                      (__HANDLE__)->Lock = HAL_UNLOCKED;    \
+                                    }while (0U)
+#endif /* USE_RTOS */
+
+#if defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) /* ARM Compiler V6 */
+  #ifndef __weak
+    #define __weak  __attribute__((weak))
+  #endif
+  #ifndef __packed
+    #define __packed  __attribute__((packed))
+  #endif
+#elif defined ( __GNUC__ ) && !defined (__CC_ARM) /* GNU Compiler */
+  #ifndef __weak
+    #define __weak   __attribute__((weak))
+  #endif /* __weak */
+  #ifndef __packed
+    #define __packed __attribute__((__packed__))
+  #endif /* __packed */
+#endif /* __GNUC__ */
+
+
+/* Macro to get variable aligned on 4-bytes, for __ICCARM__ the directive "#pragma data_alignment=4" must be used instead */
+#if defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) /* ARM Compiler V6 */
+  #ifndef __ALIGN_BEGIN
+    #define __ALIGN_BEGIN
+  #endif
+  #ifndef __ALIGN_END
+    #define __ALIGN_END      __attribute__ ((aligned (4)))
+  #endif
+#elif defined ( __GNUC__ ) && !defined (__CC_ARM) /* GNU Compiler */
+  #ifndef __ALIGN_END
+    #define __ALIGN_END    __attribute__ ((aligned (4)))
+  #endif /* __ALIGN_END */
+  #ifndef __ALIGN_BEGIN  
+    #define __ALIGN_BEGIN
+  #endif /* __ALIGN_BEGIN */
+#else
+  #ifndef __ALIGN_END
+    #define __ALIGN_END
+  #endif /* __ALIGN_END */
+  #ifndef __ALIGN_BEGIN      
+    #if defined   (__CC_ARM)      /* ARM Compiler V5*/
+      #define __ALIGN_BEGIN    __align(4)  
+    #elif defined (__ICCARM__)    /* IAR Compiler */
+      #define __ALIGN_BEGIN 
+    #endif /* __CC_ARM */
+  #endif /* __ALIGN_BEGIN */
+#endif /* __GNUC__ */
+
+/** 
+  * @brief  __NOINLINE definition
+  */ 
+#if defined ( __CC_ARM   ) || (defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)) || defined   (  __GNUC__  )
+/* ARM V4/V5 and V6 & GNU Compiler
+   -------------------------------
+*/
+#define __NOINLINE __attribute__ ( (noinline) )
+
+#elif defined ( __ICCARM__ )
+/* ICCARM Compiler
+   ---------------
+*/
+#define __NOINLINE _Pragma("optimize = no_inline")
+
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* ___STM32F0xx_HAL_DEF */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_dma.h

@@ -0,0 +1,563 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_dma.h
+  * @author  MCD Application Team
+  * @brief   Header file of DMA HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_DMA_H
+#define __STM32F0xx_HAL_DMA_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup DMA
+  * @{
+  */ 
+
+/* Exported types ------------------------------------------------------------*/ 
+
+/** @defgroup DMA_Exported_Types DMA Exported Types
+  * @{
+  */
+
+/** 
+  * @brief  DMA Configuration Structure definition  
+  */
+typedef struct
+{
+  uint32_t Direction;                 /*!< Specifies if the data will be transferred from memory to peripheral, 
+                                           from memory to memory or from peripheral to memory.
+                                           This parameter can be a value of @ref DMA_Data_transfer_direction */
+
+  uint32_t PeriphInc;                 /*!< Specifies whether the Peripheral address register should be incremented or not.
+                                           This parameter can be a value of @ref DMA_Peripheral_incremented_mode */
+                               
+  uint32_t MemInc;                    /*!< Specifies whether the memory address register should be incremented or not.
+                                           This parameter can be a value of @ref DMA_Memory_incremented_mode */
+  
+  uint32_t PeriphDataAlignment;       /*!< Specifies the Peripheral data width.
+                                           This parameter can be a value of @ref DMA_Peripheral_data_size */
+
+  uint32_t MemDataAlignment;          /*!< Specifies the Memory data width.
+                                           This parameter can be a value of @ref DMA_Memory_data_size */
+                               
+  uint32_t Mode;                      /*!< Specifies the operation mode of the DMAy Channelx.
+                                           This parameter can be a value of @ref DMA_mode
+                                           @note The circular buffer mode cannot be used if the memory-to-memory
+                                                 data transfer is configured on the selected Channel */ 
+
+  uint32_t Priority;                   /*!< Specifies the software priority for the DMAy Channelx.
+                                            This parameter can be a value of @ref DMA_Priority_level */
+} DMA_InitTypeDef;
+
+/**
+  * @brief  HAL DMA State structures definition  
+  */
+typedef enum
+{
+  HAL_DMA_STATE_RESET             = 0x00U,  /*!< DMA not yet initialized or disabled */  
+  HAL_DMA_STATE_READY             = 0x01U,  /*!< DMA initialized and ready for use   */
+  HAL_DMA_STATE_BUSY              = 0x02U,  /*!< DMA process is ongoing              */     
+  HAL_DMA_STATE_TIMEOUT           = 0x03U   /*!< DMA timeout state                   */  
+}HAL_DMA_StateTypeDef;
+
+/** 
+  * @brief  HAL DMA Error Code structure definition  
+  */ 
+typedef enum
+{
+  HAL_DMA_FULL_TRANSFER      = 0x00U,    /*!< Full transfer     */
+  HAL_DMA_HALF_TRANSFER      = 0x01U     /*!< Half Transfer     */
+}HAL_DMA_LevelCompleteTypeDef;      
+
+/** 
+  * @brief  HAL DMA Callback ID structure definition
+  */
+typedef enum
+{
+  HAL_DMA_XFER_CPLT_CB_ID          = 0x00U,    /*!< Full transfer     */
+  HAL_DMA_XFER_HALFCPLT_CB_ID      = 0x01U,    /*!< Half transfer     */
+  HAL_DMA_XFER_ERROR_CB_ID         = 0x02U,    /*!< Error             */ 
+  HAL_DMA_XFER_ABORT_CB_ID         = 0x03U,    /*!< Abort             */ 
+  HAL_DMA_XFER_ALL_CB_ID           = 0x04U     /*!< All               */ 
+    
+}HAL_DMA_CallbackIDTypeDef;                                                                 
+
+/** 
+  * @brief  DMA handle Structure definition  
+  */ 
+typedef struct __DMA_HandleTypeDef
+{  
+  DMA_Channel_TypeDef   *Instance;                                                    /*!< Register base address                  */
+  
+  DMA_InitTypeDef       Init;                                                         /*!< DMA communication parameters           */ 
+  
+  HAL_LockTypeDef       Lock;                                                         /*!< DMA locking object                     */  
+  
+  __IO HAL_DMA_StateTypeDef  State;                                                   /*!< DMA transfer state                     */
+  
+  void                  *Parent;                                                      /*!< Parent object state                    */  
+  
+  void                  (* XferCpltCallback)( struct __DMA_HandleTypeDef * hdma);     /*!< DMA transfer complete callback         */
+  
+  void                  (* XferHalfCpltCallback)( struct __DMA_HandleTypeDef * hdma); /*!< DMA Half transfer complete callback    */
+  
+  void                  (* XferErrorCallback)( struct __DMA_HandleTypeDef * hdma);    /*!< DMA transfer error callback            */
+  
+  void                  (* XferAbortCallback)( struct __DMA_HandleTypeDef * hdma);    /*!< DMA transfer abort callback            */  
+  
+  __IO uint32_t         ErrorCode;                                                    /*!< DMA Error code                         */
+  
+  DMA_TypeDef          *DmaBaseAddress;                                               /*!< DMA Channel Base Address                */
+  
+  uint32_t              ChannelIndex;                                                 /*!< DMA Channel Index                       */
+} DMA_HandleTypeDef;    
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup DMA_Exported_Constants DMA Exported Constants
+  * @{
+  */
+
+/** @defgroup DMA_Error_Code DMA Error Code
+  * @{
+  */ 
+#define HAL_DMA_ERROR_NONE          (0x00000000U)    /*!< No error             */
+#define HAL_DMA_ERROR_TE            (0x00000001U)    /*!< Transfer error       */
+#define HAL_DMA_ERROR_NO_XFER       (0x00000004U)    /*!< no ongoin transfer   */
+#define HAL_DMA_ERROR_TIMEOUT       (0x00000020U)    /*!< Timeout error        */
+#define HAL_DMA_ERROR_NOT_SUPPORTED (0x00000100U)    /*!< Not supported mode */     
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Data_transfer_direction DMA Data transfer direction
+  * @{
+  */ 
+#define DMA_PERIPH_TO_MEMORY         (0x00000000U)        /*!< Peripheral to memory direction */
+#define DMA_MEMORY_TO_PERIPH         ((uint32_t)DMA_CCR_DIR)       /*!< Memory to peripheral direction */
+#define DMA_MEMORY_TO_MEMORY         ((uint32_t)(DMA_CCR_MEM2MEM)) /*!< Memory to memory direction     */
+
+/**
+  * @}
+  */
+  
+/** @defgroup DMA_Peripheral_incremented_mode DMA Peripheral incremented mode
+  * @{
+  */ 
+#define DMA_PINC_ENABLE        ((uint32_t)DMA_CCR_PINC)  /*!< Peripheral increment mode Enable */
+#define DMA_PINC_DISABLE       (0x00000000U)    /*!< Peripheral increment mode Disable */
+/**
+  * @}
+  */ 
+
+/** @defgroup DMA_Memory_incremented_mode DMA Memory incremented mode
+  * @{
+  */ 
+#define DMA_MINC_ENABLE         ((uint32_t)DMA_CCR_MINC)  /*!< Memory increment mode Enable  */
+#define DMA_MINC_DISABLE        (0x00000000U)    /*!< Memory increment mode Disable */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Peripheral_data_size DMA Peripheral data size
+  * @{
+  */ 
+#define DMA_PDATAALIGN_BYTE          (0x00000000U)       /*!< Peripheral data alignment : Byte     */
+#define DMA_PDATAALIGN_HALFWORD      ((uint32_t)DMA_CCR_PSIZE_0)  /*!< Peripheral data alignment : HalfWord */
+#define DMA_PDATAALIGN_WORD          ((uint32_t)DMA_CCR_PSIZE_1)  /*!< Peripheral data alignment : Word     */
+/**
+  * @}
+  */ 
+
+/** @defgroup DMA_Memory_data_size DMA Memory data size
+  * @{ 
+  */
+#define DMA_MDATAALIGN_BYTE          (0x00000000U)       /*!< Memory data alignment : Byte     */
+#define DMA_MDATAALIGN_HALFWORD      ((uint32_t)DMA_CCR_MSIZE_0)  /*!< Memory data alignment : HalfWord */
+#define DMA_MDATAALIGN_WORD          ((uint32_t)DMA_CCR_MSIZE_1)  /*!< Memory data alignment : Word     */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_mode DMA mode
+  * @{
+  */ 
+#define DMA_NORMAL         (0x00000000U)      /*!< Normal Mode                  */
+#define DMA_CIRCULAR       ((uint32_t)DMA_CCR_CIRC)    /*!< Circular Mode                */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Priority_level DMA Priority level
+  * @{
+  */
+#define DMA_PRIORITY_LOW             (0x00000000U)    /*!< Priority level : Low       */
+#define DMA_PRIORITY_MEDIUM          ((uint32_t)DMA_CCR_PL_0)  /*!< Priority level : Medium    */
+#define DMA_PRIORITY_HIGH            ((uint32_t)DMA_CCR_PL_1)  /*!< Priority level : High      */
+#define DMA_PRIORITY_VERY_HIGH       ((uint32_t)DMA_CCR_PL)    /*!< Priority level : Very_High */
+/**
+  * @}
+  */ 
+
+
+/** @defgroup DMA_interrupt_enable_definitions DMA interrupt enable definitions
+  * @{
+  */
+#define DMA_IT_TC                         ((uint32_t)DMA_CCR_TCIE)
+#define DMA_IT_HT                         ((uint32_t)DMA_CCR_HTIE)
+#define DMA_IT_TE                         ((uint32_t)DMA_CCR_TEIE)
+/**
+  * @}
+  */
+
+/** @defgroup DMA_flag_definitions DMA flag definitions
+  * @{
+  */ 
+
+#define DMA_FLAG_GL1                      (0x00000001U) /*!< Channel 1 global interrupt flag  */
+#define DMA_FLAG_TC1                      (0x00000002U) /*!< Channel 1 transfer complete flag */
+#define DMA_FLAG_HT1                      (0x00000004U) /*!< Channel 1 half transfer flag     */
+#define DMA_FLAG_TE1                      (0x00000008U) /*!< Channel 1 transfer error flag    */
+#define DMA_FLAG_GL2                      (0x00000010U) /*!< Channel 2 global interrupt flag  */
+#define DMA_FLAG_TC2                      (0x00000020U) /*!< Channel 2 transfer complete flag */
+#define DMA_FLAG_HT2                      (0x00000040U) /*!< Channel 2 half transfer flag     */
+#define DMA_FLAG_TE2                      (0x00000080U) /*!< Channel 2 transfer error flag    */
+#define DMA_FLAG_GL3                      (0x00000100U) /*!< Channel 3 global interrupt flag  */
+#define DMA_FLAG_TC3                      (0x00000200U) /*!< Channel 3 transfer complete flag */
+#define DMA_FLAG_HT3                      (0x00000400U) /*!< Channel 3 half transfer flag     */
+#define DMA_FLAG_TE3                      (0x00000800U) /*!< Channel 3 transfer error flag    */
+#define DMA_FLAG_GL4                      (0x00001000U) /*!< Channel 4 global interrupt flag  */
+#define DMA_FLAG_TC4                      (0x00002000U) /*!< Channel 4 transfer complete flag */
+#define DMA_FLAG_HT4                      (0x00004000U) /*!< Channel 4 half transfer flag     */
+#define DMA_FLAG_TE4                      (0x00008000U) /*!< Channel 4 transfer error flag    */
+#define DMA_FLAG_GL5                      (0x00010000U) /*!< Channel 5 global interrupt flag  */
+#define DMA_FLAG_TC5                      (0x00020000U) /*!< Channel 5 transfer complete flag */
+#define DMA_FLAG_HT5                      (0x00040000U) /*!< Channel 5 half transfer flag     */
+#define DMA_FLAG_TE5                      (0x00080000U) /*!< Channel 5 transfer error flag    */
+#define DMA_FLAG_GL6                      (0x00100000U) /*!< Channel 6 global interrupt flag  */
+#define DMA_FLAG_TC6                      (0x00200000U) /*!< Channel 6 transfer complete flag */
+#define DMA_FLAG_HT6                      (0x00400000U) /*!< Channel 6 half transfer flag     */
+#define DMA_FLAG_TE6                      (0x00800000U) /*!< Channel 6 transfer error flag    */
+#define DMA_FLAG_GL7                      (0x01000000U) /*!< Channel 7 global interrupt flag  */
+#define DMA_FLAG_TC7                      (0x02000000U) /*!< Channel 7 transfer complete flag */
+#define DMA_FLAG_HT7                      (0x04000000U) /*!< Channel 7 half transfer flag     */
+#define DMA_FLAG_TE7                      (0x08000000U) /*!< Channel 7 transfer error flag    */
+
+/**
+  * @}
+  */
+
+#if defined(SYSCFG_CFGR1_DMA_RMP)
+/** @defgroup HAL_DMA_remapping HAL DMA remapping
+  *        Elements values convention: 0xYYYYYYYY
+  *           - YYYYYYYY  : Position in the SYSCFG register CFGR1
+  * @{  
+  */
+#define DMA_REMAP_ADC_DMA_CH2         ((uint32_t)SYSCFG_CFGR1_ADC_DMA_RMP) /*!< ADC DMA remap 
+                                                                         0: No remap (ADC DMA requests mapped on DMA channel 1
+                                                                         1: Remap (ADC DMA requests mapped on DMA channel 2 */
+#define DMA_REMAP_USART1_TX_DMA_CH4   ((uint32_t)SYSCFG_CFGR1_USART1TX_DMA_RMP) /*!< USART1 TX DMA remap 
+                                                                         0: No remap (USART1_TX DMA request mapped on DMA channel 2
+                                                                         1: Remap (USART1_TX DMA request mapped on DMA channel 4 */
+#define DMA_REMAP_USART1_RX_DMA_CH5   ((uint32_t)SYSCFG_CFGR1_USART1RX_DMA_RMP) /*!< USART1 RX DMA remap 
+                                                                         0: No remap (USART1_RX DMA request mapped on DMA channel 3
+                                                                         1: Remap (USART1_RX DMA request mapped on DMA channel 5 */
+#define DMA_REMAP_TIM16_DMA_CH4       ((uint32_t)SYSCFG_CFGR1_TIM16_DMA_RMP) /*!< TIM16 DMA request remap
+                                                                         0: No remap (TIM16_CH1 and TIM16_UP DMA requests mapped on DMA channel 3)
+                                                                         1: Remap (TIM16_CH1 and TIM16_UP DMA requests mapped on DMA channel 4) */
+#define DMA_REMAP_TIM17_DMA_CH2       ((uint32_t)SYSCFG_CFGR1_TIM17_DMA_RMP) /*!< TIM17 DMA request remap
+                                                                         0: No remap (TIM17_CH1 and TIM17_UP DMA requests mapped on DMA channel 1
+                                                                         1: Remap (TIM17_CH1 and TIM17_UP DMA requests mapped on DMA channel 2) */
+#if defined (STM32F070xB)
+#define DMA_REMAP_USART3_DMA_CH32     ((uint32_t)SYSCFG_CFGR1_USART3_DMA_RMP) /*!< USART3 DMA request remapping bit. Available on STM32F070xB devices only.
+                                                                         0: Disabled, need to remap before use 
+                                                                         1: Remap (USART3_RX and USART3_TX DMA requests mapped on DMA channel 3 and 2 respectively) */
+
+#endif
+
+#if defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx)
+#define DMA_REMAP_TIM16_DMA_CH6       ((uint32_t)SYSCFG_CFGR1_TIM16_DMA_RMP2) /*!< TIM16 alternate DMA request remapping bit. Available on STM32F07x devices only
+                                                                         0: No alternate remap (TIM16 DMA requestsmapped according to TIM16_DMA_RMP bit)
+                                                                         1: Alternate remap (TIM16_CH1 and TIM16_UP DMA requests mapped on DMA channel 6) */
+#define DMA_REMAP_TIM17_DMA_CH7       ((uint32_t)SYSCFG_CFGR1_TIM17_DMA_RMP2) /*!< TIM17 alternate DMA request remapping bit. Available on STM32F07x devices only
+                                                                         0: No alternate remap (TIM17 DMA requestsmapped according to TIM17_DMA_RMP bit)
+                                                                         1: Alternate remap (TIM17_CH1 and TIM17_UP DMA requests mapped on DMA channel 7) */
+#define DMA_REMAP_SPI2_DMA_CH67       ((uint32_t)SYSCFG_CFGR1_SPI2_DMA_RMP) /*!< SPI2 DMA request remapping bit. Available on STM32F07x devices only.
+                                                                         0: No remap (SPI2_RX and SPI2_TX DMA requests mapped on DMA channel 4 and 5 respectively)
+                                                                         1: Remap (SPI2_RX and SPI2_TX DMA requests mapped on DMA channel 6 and 7 respectively) */
+#define DMA_REMAP_USART2_DMA_CH67     ((uint32_t)SYSCFG_CFGR1_USART2_DMA_RMP) /*!< USART2 DMA request remapping bit. Available on STM32F07x devices only.
+                                                                         0: No remap (USART2_RX and USART2_TX DMA requests mapped on DMA channel 5 and 4 respectively)
+                                                                         1: 1: Remap (USART2_RX and USART2_TX DMA requests mapped on DMA channel 6 and 7 respectively) */
+#define DMA_REMAP_USART3_DMA_CH32     ((uint32_t)SYSCFG_CFGR1_USART3_DMA_RMP) /*!< USART3 DMA request remapping bit. Available on STM32F07x devices only.
+                                                                         0: No remap (USART3_RX and USART3_TX DMA requests mapped on DMA channel 6 and 7 respectively)
+                                                                         1: Remap (USART3_RX and USART3_TX DMA requests mapped on DMA channel 3 and 2 respectively) */
+#define DMA_REMAP_I2C1_DMA_CH76       ((uint32_t)SYSCFG_CFGR1_I2C1_DMA_RMP) /*!< I2C1 DMA request remapping bit. Available on STM32F07x devices only.
+                                                                         0: No remap (I2C1_RX and I2C1_TX DMA requests mapped on DMA channel 3 and 2 respectively)
+                                                                         1: Remap (I2C1_RX and I2C1_TX DMA requests mapped on DMA channel 7 and 6 respectively) */
+#define DMA_REMAP_TIM1_DMA_CH6        ((uint32_t)SYSCFG_CFGR1_TIM1_DMA_RMP) /*!< TIM1 DMA request remapping bit. Available on STM32F07x devices only.
+                                                                         0: No remap (TIM1_CH1, TIM1_CH2 and TIM1_CH3 DMA requests mapped on DMA channel 2, 3 and 4 respectively)
+                                                                         1: Remap (TIM1_CH1, TIM1_CH2 and TIM1_CH3 DMA requests mapped on DMA channel 6 */
+#define DMA_REMAP_TIM2_DMA_CH7        ((uint32_t)SYSCFG_CFGR1_TIM2_DMA_RMP) /*!< TIM2 DMA request remapping bit. Available on STM32F07x devices only.
+                                                                         0: No remap (TIM2_CH2 and TIM2_CH4 DMA requests mapped on DMA channel 3 and 4 respectively)
+                                                                         1: Remap (TIM2_CH2 and TIM2_CH4 DMA requests mapped on DMA channel 7 */
+#define DMA_REMAP_TIM3_DMA_CH6        ((uint32_t)SYSCFG_CFGR1_TIM3_DMA_RMP) /*!< TIM3 DMA request remapping bit. Available on STM32F07x devices only.
+                                                                         0: No remap (TIM3_CH1 and TIM3_TRIG DMA requests mapped on DMA channel 4)
+                                                                         1: Remap (TIM3_CH1 and TIM3_TRIG DMA requests mapped on DMA channel 6) */
+#endif
+
+/**
+  * @}
+  */
+
+#endif /* SYSCFG_CFGR1_DMA_RMP */
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup DMA_Exported_Macros DMA Exported Macros
+  * @{
+  */
+
+/** @brief  Reset DMA handle state
+  * @param  __HANDLE__ DMA handle.
+  * @retval None
+  */
+#define __HAL_DMA_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_DMA_STATE_RESET)
+
+/**
+  * @brief  Enable the specified DMA Channel.
+  * @param  __HANDLE__ DMA handle
+  * @retval None
+  */
+#define __HAL_DMA_ENABLE(__HANDLE__)        ((__HANDLE__)->Instance->CCR |= DMA_CCR_EN)
+
+/**
+  * @brief  Disable the specified DMA Channel.
+  * @param  __HANDLE__ DMA handle
+  * @retval None
+  */
+#define __HAL_DMA_DISABLE(__HANDLE__)       ((__HANDLE__)->Instance->CCR &= ~DMA_CCR_EN)
+
+
+/* Interrupt & Flag management */
+
+/**
+  * @brief  Enables the specified DMA Channel interrupts.
+  * @param  __HANDLE__ DMA handle
+  * @param __INTERRUPT__ specifies the DMA interrupt sources to be enabled or disabled. 
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_IT_TC:  Transfer complete interrupt mask
+  *            @arg DMA_IT_HT:  Half transfer complete interrupt mask
+  *            @arg DMA_IT_TE:  Transfer error interrupt mask
+  * @retval None
+  */
+#define __HAL_DMA_ENABLE_IT(__HANDLE__, __INTERRUPT__)   ((__HANDLE__)->Instance->CCR |= (__INTERRUPT__))
+
+/**
+  * @brief  Disables the specified DMA Channel interrupts.
+  * @param  __HANDLE__ DMA handle
+  * @param __INTERRUPT__ specifies the DMA interrupt sources to be enabled or disabled. 
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_IT_TC:  Transfer complete interrupt mask
+  *            @arg DMA_IT_HT:  Half transfer complete interrupt mask
+  *            @arg DMA_IT_TE:  Transfer error interrupt mask
+  * @retval None
+  */
+#define __HAL_DMA_DISABLE_IT(__HANDLE__, __INTERRUPT__)  ((__HANDLE__)->Instance->CCR &= ~(__INTERRUPT__))
+
+/**
+  * @brief  Checks whether the specified DMA Channel interrupt is enabled or disabled.
+  * @param  __HANDLE__ DMA handle
+  * @param  __INTERRUPT__ specifies the DMA interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg DMA_IT_TC:  Transfer complete interrupt mask
+  *            @arg DMA_IT_HT:  Half transfer complete interrupt mask
+  *            @arg DMA_IT_TE:  Transfer error interrupt mask
+  * @retval The state of DMA_IT (SET or RESET).
+  */
+#define __HAL_DMA_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)  (((__HANDLE__)->Instance->CCR & (__INTERRUPT__)))
+
+/**
+  * @brief  Returns the number of remaining data units in the current DMAy Channelx transfer.
+  * @param  __HANDLE__ DMA handle
+  *   
+  * @retval The number of remaining data units in the current DMA Channel transfer.
+  */
+#define __HAL_DMA_GET_COUNTER(__HANDLE__) ((__HANDLE__)->Instance->CNDTR)
+
+#if defined(SYSCFG_CFGR1_DMA_RMP)
+/** @brief  DMA remapping enable/disable macros
+  * @param __DMA_REMAP__ This parameter can be a value of @ref HAL_DMA_remapping
+  */
+#define __HAL_DMA_REMAP_CHANNEL_ENABLE(__DMA_REMAP__)   do {assert_param(IS_DMA_REMAP((__DMA_REMAP__)));                  \
+                                                           SYSCFG->CFGR1 |= (__DMA_REMAP__);                              \
+                                                         }while(0)
+#define __HAL_DMA_REMAP_CHANNEL_DISABLE(__DMA_REMAP__)  do {assert_param(IS_DMA_REMAP((__DMA_REMAP__)));                  \
+                                                           SYSCFG->CFGR1 &= ~(__DMA_REMAP__);                             \
+                                                         }while(0)
+#endif /* SYSCFG_CFGR1_DMA_RMP */
+
+/**
+  * @}
+  */
+
+/* Include DMA HAL Extension module */
+#include "stm32f0xx_hal_dma_ex.h"   
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup DMA_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup DMA_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization and de-initialization functions *****************************/
+HAL_StatusTypeDef HAL_DMA_Init(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_DeInit (DMA_HandleTypeDef *hdma);
+/**
+  * @}
+  */
+
+/** @addtogroup DMA_Exported_Functions_Group2
+  * @{
+  */
+/* Input and Output operation functions *****************************************************/
+HAL_StatusTypeDef HAL_DMA_Start (DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
+HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
+HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_Abort_IT(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, uint32_t CompleteLevel, uint32_t Timeout);
+void HAL_DMA_IRQHandler(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_RegisterCallback(DMA_HandleTypeDef *hdma, HAL_DMA_CallbackIDTypeDef CallbackID, void (* pCallback)( DMA_HandleTypeDef * _hdma));
+HAL_StatusTypeDef HAL_DMA_UnRegisterCallback(DMA_HandleTypeDef *hdma, HAL_DMA_CallbackIDTypeDef CallbackID);
+
+/**
+  * @}
+  */
+
+/** @addtogroup DMA_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral State and Error functions ***************************************/
+HAL_DMA_StateTypeDef HAL_DMA_GetState(DMA_HandleTypeDef *hdma);
+uint32_t             HAL_DMA_GetError(DMA_HandleTypeDef *hdma);
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+/** @addtogroup DMA_Private_Macros
+  * @{
+  */
+#define IS_DMA_DIRECTION(DIRECTION) (((DIRECTION) == DMA_PERIPH_TO_MEMORY ) || \
+                                     ((DIRECTION) == DMA_MEMORY_TO_PERIPH)  || \
+                                     ((DIRECTION) == DMA_MEMORY_TO_MEMORY)) 
+#define IS_DMA_PERIPHERAL_INC_STATE(STATE) (((STATE) == DMA_PINC_ENABLE) || \
+                                            ((STATE) == DMA_PINC_DISABLE))
+
+#define IS_DMA_MEMORY_INC_STATE(STATE) (((STATE) == DMA_MINC_ENABLE)  || \
+                                        ((STATE) == DMA_MINC_DISABLE))
+
+#define IS_DMA_PERIPHERAL_DATA_SIZE(SIZE) (((SIZE) == DMA_PDATAALIGN_BYTE)     || \
+                                           ((SIZE) == DMA_PDATAALIGN_HALFWORD) || \
+                                           ((SIZE) == DMA_PDATAALIGN_WORD))
+
+#define IS_DMA_MEMORY_DATA_SIZE(SIZE) (((SIZE) == DMA_MDATAALIGN_BYTE)     || \
+                                       ((SIZE) == DMA_MDATAALIGN_HALFWORD) || \
+                                       ((SIZE) == DMA_MDATAALIGN_WORD ))
+
+#define IS_DMA_MODE(MODE) (((MODE) == DMA_NORMAL )  || \
+                           ((MODE) == DMA_CIRCULAR))
+#define IS_DMA_PRIORITY(PRIORITY) (((PRIORITY) == DMA_PRIORITY_LOW )   || \
+                                   ((PRIORITY) == DMA_PRIORITY_MEDIUM) || \
+                                   ((PRIORITY) == DMA_PRIORITY_HIGH)   || \
+                                   ((PRIORITY) == DMA_PRIORITY_VERY_HIGH)) 
+#define IS_DMA_BUFFER_SIZE(SIZE) (((SIZE) >= 0x1U) && ((SIZE) < 0x10000U))
+
+#if defined(SYSCFG_CFGR1_DMA_RMP)
+
+#if defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx)
+#define IS_DMA_REMAP(RMP) (((RMP) == DMA_REMAP_ADC_DMA_CH2)          || \
+                              ((RMP) == DMA_REMAP_USART1_TX_DMA_CH4) || \
+                              ((RMP) == DMA_REMAP_USART1_RX_DMA_CH5) || \
+                              ((RMP) == DMA_REMAP_TIM16_DMA_CH4)     || \
+                              ((RMP) == DMA_REMAP_TIM17_DMA_CH2)     || \
+                              ((RMP) == DMA_REMAP_TIM16_DMA_CH6)     || \
+                              ((RMP) == DMA_REMAP_TIM17_DMA_CH7)     || \
+                              ((RMP) == DMA_REMAP_SPI2_DMA_CH67)     || \
+                              ((RMP) == DMA_REMAP_USART2_DMA_CH67)   || \
+                              ((RMP) == DMA_REMAP_USART3_DMA_CH32)   || \
+                              ((RMP) == DMA_REMAP_I2C1_DMA_CH76)     || \
+                              ((RMP) == DMA_REMAP_TIM1_DMA_CH6)      || \
+                              ((RMP) == DMA_REMAP_TIM2_DMA_CH7)      || \
+                              ((RMP) == DMA_REMAP_TIM3_DMA_CH6))
+#elif defined (STM32F070xB)
+#define IS_DMA_REMAP(RMP)     (((RMP) == DMA_REMAP_USART3_DMA_CH32)  || \
+                              ((RMP) == DMA_REMAP_ADC_DMA_CH2)       || \
+                              ((RMP) == DMA_REMAP_USART1_TX_DMA_CH4) || \
+                              ((RMP) == DMA_REMAP_USART1_RX_DMA_CH5) || \
+                              ((RMP) == DMA_REMAP_TIM16_DMA_CH4)     || \
+                              ((RMP) == DMA_REMAP_TIM17_DMA_CH2))
+#else
+#define IS_DMA_REMAP(RMP)     (((RMP) == DMA_REMAP_ADC_DMA_CH2)      || \
+                              ((RMP) == DMA_REMAP_USART1_TX_DMA_CH4) || \
+                              ((RMP) == DMA_REMAP_USART1_RX_DMA_CH5) || \
+                              ((RMP) == DMA_REMAP_TIM16_DMA_CH4)     || \
+                              ((RMP) == DMA_REMAP_TIM17_DMA_CH2))
+#endif
+
+#endif /* SYSCFG_CFGR1_DMA_RMP */  
+
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_DMA_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_dma_ex.h

@@ -0,0 +1,811 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_dma_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of DMA HAL Extension module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_DMA_EX_H
+#define __STM32F0xx_HAL_DMA_EX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup DMAEx DMAEx
+  * @brief DMA HAL module driver
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/ 
+/* Exported constants --------------------------------------------------------*/
+#if defined(STM32F091xC) || defined(STM32F098xx) || defined(STM32F030xC)
+/** @defgroup DMAEx_Exported_Constants DMAEx Exported Constants
+  * @{
+  */ 
+#define DMA1_CHANNEL1_RMP                                     0x00000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#define DMA1_CHANNEL2_RMP                                     0x10000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#define DMA1_CHANNEL3_RMP                                     0x20000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#define DMA1_CHANNEL4_RMP                                     0x30000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#define DMA1_CHANNEL5_RMP                                     0x40000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#if !defined(STM32F030xC)
+#define DMA1_CHANNEL6_RMP                                     0x50000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#define DMA1_CHANNEL7_RMP                                     0x60000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#define DMA2_CHANNEL1_RMP                                     0x00000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#define DMA2_CHANNEL2_RMP                                     0x10000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#define DMA2_CHANNEL3_RMP                                     0x20000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#define DMA2_CHANNEL4_RMP                                     0x30000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#define DMA2_CHANNEL5_RMP                                     0x40000000 /*!< Internal define for remaping on STM32F09x/30xC */
+#endif /* !defined(STM32F030xC) */
+
+/****************** DMA1 remap bit field definition********************/
+/* DMA1 - Channel 1 */
+#define HAL_DMA1_CH1_DEFAULT      (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_DEFAULT)       /*!< Default remap position for DMA1 */   
+#define HAL_DMA1_CH1_ADC          (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_ADC)       /*!< Remap ADC on DMA1 Channel 1*/   
+#define HAL_DMA1_CH1_TIM17_CH1    (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_TIM17_CH1) /*!< Remap TIM17 channel 1 on DMA1 channel 1 */
+#define HAL_DMA1_CH1_TIM17_UP     (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_TIM17_UP)  /*!< Remap TIM17 up on DMA1 channel 1 */ 
+#define HAL_DMA1_CH1_USART1_RX    (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_USART1_RX) /*!< Remap USART1 Rx on DMA1 channel 1 */ 
+#define HAL_DMA1_CH1_USART2_RX    (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_USART2_RX) /*!< Remap USART2 Rx on DMA1 channel 1 */ 
+#define HAL_DMA1_CH1_USART3_RX    (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_USART3_RX) /*!< Remap USART3 Rx on DMA1 channel 1 */ 
+#define HAL_DMA1_CH1_USART4_RX    (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_USART4_RX) /*!< Remap USART4 Rx on DMA1 channel 1 */ 
+#define HAL_DMA1_CH1_USART5_RX    (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_USART5_RX) /*!< Remap USART5 Rx on DMA1 channel 1 */ 
+#define HAL_DMA1_CH1_USART6_RX    (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_USART6_RX) /*!< Remap USART6 Rx on DMA1 channel 1 */ 
+#if !defined(STM32F030xC)
+#define HAL_DMA1_CH1_USART7_RX    (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_USART7_RX) /*!< Remap USART7 Rx on DMA1 channel 1 */ 
+#define HAL_DMA1_CH1_USART8_RX    (uint32_t) (DMA1_CHANNEL1_RMP | DMA1_CSELR_CH1_USART8_RX) /*!< Remap USART8 Rx on DMA1 channel 1 */ 
+#endif /* !defined(STM32F030xC) */
+
+/* DMA1 - Channel 2 */
+#define HAL_DMA1_CH2_DEFAULT      (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_DEFAULT)       /*!< Default remap position for DMA1 */   
+#define HAL_DMA1_CH2_ADC          (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_ADC)       /*!< Remap ADC on DMA1 channel 2 */  
+#define HAL_DMA1_CH2_I2C1_TX      (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_I2C1_TX)   /*!< Remap I2C1 Tx on DMA1 channel 2 */ 
+#define HAL_DMA1_CH2_SPI1_RX      (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_SPI1_RX)   /*!< Remap SPI1 Rx on DMA1 channel 2 */ 
+#define HAL_DMA1_CH2_TIM1_CH1     (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_TIM1_CH1)  /*!< Remap TIM1 channel 1 on DMA1 channel 2 */
+#define HAL_DMA1_CH2_TIM17_CH1    (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_TIM17_CH1) /*!< Remap TIM17 channel 1 on DMA1 channel 2 */
+#define HAL_DMA1_CH2_TIM17_UP     (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_TIM17_UP)  /*!< Remap TIM17 up on DMA1 channel 2 */ 
+#define HAL_DMA1_CH2_USART1_TX    (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_USART1_TX) /*!< Remap USART1 Tx on DMA1 channel 2 */ 
+#define HAL_DMA1_CH2_USART2_TX    (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_USART2_TX) /*!< Remap USART2 Tx on DMA1 channel 2 */ 
+#define HAL_DMA1_CH2_USART3_TX    (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_USART3_TX) /*!< Remap USART3 Tx on DMA1 channel 2 */ 
+#define HAL_DMA1_CH2_USART4_TX    (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_USART4_TX) /*!< Remap USART4 Tx on DMA1 channel 2 */ 
+#define HAL_DMA1_CH2_USART5_TX    (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_USART5_TX) /*!< Remap USART5 Tx on DMA1 channel 2 */ 
+#define HAL_DMA1_CH2_USART6_TX    (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_USART6_TX) /*!< Remap USART6 Tx on DMA1 channel 2 */ 
+#if !defined(STM32F030xC)
+#define HAL_DMA1_CH2_USART7_TX    (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_USART7_TX) /*!< Remap USART7 Tx on DMA1 channel 2 */ 
+#define HAL_DMA1_CH2_USART8_TX    (uint32_t) (DMA1_CHANNEL2_RMP | DMA1_CSELR_CH2_USART8_TX) /*!< Remap USART8 Tx on DMA1 channel 2 */ 
+#endif /* !defined(STM32F030xC) */
+
+/* DMA1 - Channel 3 */
+#define HAL_DMA1_CH3_DEFAULT      (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_DEFAULT)       /*!< Default remap position for DMA1 */   
+#define HAL_DMA1_CH3_TIM6_UP      (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_TIM6_UP)   /*!< Remap TIM6 up on DMA1 channel 3 */ 
+#if !defined(STM32F030xC)
+#define HAL_DMA1_CH3_DAC_CH1      (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_DAC_CH1)   /*!< Remap DAC Channel 1on DMA1 channel 3 */ 
+#endif /* !defined(STM32F030xC) */
+#define HAL_DMA1_CH3_I2C1_RX      (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_I2C1_RX)   /*!< Remap I2C1 Rx on DMA1 channel 3 */ 
+#define HAL_DMA1_CH3_SPI1_TX      (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_SPI1_TX)   /*!< Remap SPI1 Tx on DMA1 channel 3 */ 
+#define HAL_DMA1_CH3_TIM1_CH2     (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_TIM1_CH2)  /*!< Remap TIM1 channel 2 on DMA1 channel 3 */
+#if !defined(STM32F030xC)
+#define HAL_DMA1_CH3_TIM2_CH2     (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_TIM2_CH2)  /*!< Remap TIM2 channel 2 on DMA1 channel 3 */
+#endif /* !defined(STM32F030xC) */
+#define HAL_DMA1_CH3_TIM16_CH1    (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_TIM16_CH1) /*!< Remap TIM16 channel 1 on DMA1 channel 3 */
+#define HAL_DMA1_CH3_TIM16_UP     (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_TIM16_UP)  /*!< Remap TIM16 up on DMA1 channel 3 */ 
+#define HAL_DMA1_CH3_USART1_RX    (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_USART1_RX) /*!< Remap USART1 Rx on DMA1 channel 3 */ 
+#define HAL_DMA1_CH3_USART2_RX    (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_USART2_RX) /*!< Remap USART2 Rx on DMA1 channel 3 */ 
+#define HAL_DMA1_CH3_USART3_RX    (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_USART3_RX) /*!< Remap USART3 Rx on DMA1 channel 3 */ 
+#define HAL_DMA1_CH3_USART4_RX    (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_USART4_RX) /*!< Remap USART4 Rx on DMA1 channel 3 */ 
+#define HAL_DMA1_CH3_USART5_RX    (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_USART5_RX) /*!< Remap USART5 Rx on DMA1 channel 3 */ 
+#define HAL_DMA1_CH3_USART6_RX    (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_USART6_RX) /*!< Remap USART6 Rx on DMA1 channel 3 */ 
+#if !defined(STM32F030xC)
+#define HAL_DMA1_CH3_USART7_RX    (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_USART7_RX) /*!< Remap USART7 Rx on DMA1 channel 3 */ 
+#define HAL_DMA1_CH3_USART8_RX    (uint32_t) (DMA1_CHANNEL3_RMP | DMA1_CSELR_CH3_USART8_RX) /*!< Remap USART8 Rx on DMA1 channel 3 */ 
+#endif /* !defined(STM32F030xC) */
+
+/* DMA1 - Channel 4 */
+#define HAL_DMA1_CH4_DEFAULT      (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_DEFAULT)       /*!< Default remap position for DMA1 */   
+#define HAL_DMA1_CH4_TIM7_UP      (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_TIM7_UP)   /*!< Remap TIM7 up on DMA1 channel 4 */ 
+#if !defined(STM32F030xC)
+#define HAL_DMA1_CH4_DAC_CH2      (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_DAC_CH2)   /*!< Remap DAC Channel 2 on DMA1 channel 4 */
+#endif /* !defined(STM32F030xC) */
+#define HAL_DMA1_CH4_I2C2_TX      (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_I2C2_TX)   /*!< Remap I2C2 Tx on DMA1 channel 4 */ 
+#define HAL_DMA1_CH4_SPI2_RX      (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_SPI2_RX)   /*!< Remap SPI2 Rx on DMA1 channel 4 */ 
+#if !defined(STM32F030xC)
+#define HAL_DMA1_CH4_TIM2_CH4     (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_TIM2_CH4)  /*!< Remap TIM2 channel 4 on DMA1 channel 4 */
+#endif /* !defined(STM32F030xC) */
+#define HAL_DMA1_CH4_TIM3_CH1     (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_TIM3_CH1)  /*!< Remap TIM3 channel 1 on DMA1 channel 4 */
+#define HAL_DMA1_CH4_TIM3_TRIG    (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_TIM3_TRIG) /*!< Remap TIM3 Trig on DMA1 channel 4 */ 
+#define HAL_DMA1_CH4_TIM16_CH1    (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_TIM16_CH1) /*!< Remap TIM16 channel 1 on DMA1 channel 4 */
+#define HAL_DMA1_CH4_TIM16_UP     (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_TIM16_UP)  /*!< Remap TIM16 up on DMA1 channel 4 */ 
+#define HAL_DMA1_CH4_USART1_TX    (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_USART1_TX) /*!< Remap USART1 Tx on DMA1 channel 4 */ 
+#define HAL_DMA1_CH4_USART2_TX    (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_USART2_TX) /*!< Remap USART2 Tx on DMA1 channel 4 */ 
+#define HAL_DMA1_CH4_USART3_TX    (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_USART3_TX) /*!< Remap USART3 Tx on DMA1 channel 4 */ 
+#define HAL_DMA1_CH4_USART4_TX    (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_USART4_TX) /*!< Remap USART4 Tx on DMA1 channel 4 */ 
+#define HAL_DMA1_CH4_USART5_TX    (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_USART5_TX) /*!< Remap USART5 Tx on DMA1 channel 4 */ 
+#define HAL_DMA1_CH4_USART6_TX    (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_USART6_TX) /*!< Remap USART6 Tx on DMA1 channel 4 */ 
+#if !defined(STM32F030xC)
+#define HAL_DMA1_CH4_USART7_TX    (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_USART7_TX) /*!< Remap USART7 Tx on DMA1 channel 4 */ 
+#define HAL_DMA1_CH4_USART8_TX    (uint32_t) (DMA1_CHANNEL4_RMP | DMA1_CSELR_CH4_USART8_TX) /*!< Remap USART8 Tx on DMA1 channel 4 */ 
+#endif /* !defined(STM32F030xC) */
+
+/* DMA1 - Channel 5 */
+#define HAL_DMA1_CH5_DEFAULT      (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_DEFAULT)       /*!< Default remap position for DMA1 */   
+#define HAL_DMA1_CH5_I2C2_RX      (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_I2C2_RX)   /*!< Remap I2C2 Rx on DMA1 channel 5 */ 
+#define HAL_DMA1_CH5_SPI2_TX      (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_SPI2_TX)   /*!< Remap SPI1 Tx on DMA1 channel 5 */ 
+#define HAL_DMA1_CH5_TIM1_CH3     (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_TIM1_CH3)  /*!< Remap TIM1 channel 3 on DMA1 channel 5 */
+#define HAL_DMA1_CH5_USART1_RX    (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_USART1_RX) /*!< Remap USART1 Rx on DMA1 channel 5 */ 
+#define HAL_DMA1_CH5_USART2_RX    (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_USART2_RX) /*!< Remap USART2 Rx on DMA1 channel 5 */ 
+#define HAL_DMA1_CH5_USART3_RX    (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_USART3_RX) /*!< Remap USART3 Rx on DMA1 channel 5 */ 
+#define HAL_DMA1_CH5_USART4_RX    (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_USART4_RX) /*!< Remap USART4 Rx on DMA1 channel 5 */ 
+#define HAL_DMA1_CH5_USART5_RX    (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_USART5_RX) /*!< Remap USART5 Rx on DMA1 channel 5 */ 
+#define HAL_DMA1_CH5_USART6_RX    (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_USART6_RX) /*!< Remap USART6 Rx on DMA1 channel 5 */ 
+#if !defined(STM32F030xC)
+#define HAL_DMA1_CH5_USART7_RX    (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_USART7_RX) /*!< Remap USART7 Rx on DMA1 channel 5 */ 
+#define HAL_DMA1_CH5_USART8_RX    (uint32_t) (DMA1_CHANNEL5_RMP | DMA1_CSELR_CH5_USART8_RX) /*!< Remap USART8 Rx on DMA1 channel 5 */ 
+#endif /* !defined(STM32F030xC) */
+
+#if !defined(STM32F030xC)
+/* DMA1 - Channel 6 */
+#define HAL_DMA1_CH6_DEFAULT      (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_DEFAULT)       /*!< Default remap position for DMA1 */   
+#define HAL_DMA1_CH6_I2C1_TX      (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_I2C1_TX)   /*!< Remap I2C1 Tx on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_SPI2_RX      (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_SPI2_RX)   /*!< Remap SPI2 Rx on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_TIM1_CH1     (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_TIM1_CH1)  /*!< Remap TIM1 channel 1 on DMA1 channel 6 */
+#define HAL_DMA1_CH6_TIM1_CH2     (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_TIM1_CH2)  /*!< Remap TIM1 channel 2 on DMA1 channel 6 */
+#define HAL_DMA1_CH6_TIM1_CH3     (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_TIM1_CH3)  /*!< Remap TIM1 channel 3 on DMA1 channel 6 */
+#define HAL_DMA1_CH6_TIM3_CH1     (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_TIM3_CH1)  /*!< Remap TIM3 channel 1 on DMA1 channel 6 */
+#define HAL_DMA1_CH6_TIM3_TRIG    (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_TIM3_TRIG) /*!< Remap TIM3 Trig on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_TIM16_CH1    (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_TIM16_CH1) /*!< Remap TIM16 channel 1 on DMA1 channel 6 */
+#define HAL_DMA1_CH6_TIM16_UP     (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_TIM16_UP)  /*!< Remap TIM16 up on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_USART1_RX    (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_USART1_RX) /*!< Remap USART1 Rx on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_USART2_RX    (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_USART2_RX) /*!< Remap USART2 Rx on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_USART3_RX    (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_USART3_RX) /*!< Remap USART3 Rx on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_USART4_RX    (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_USART4_RX) /*!< Remap USART4 Rx on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_USART5_RX    (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_USART5_RX) /*!< Remap USART5 Rx on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_USART6_RX    (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_USART6_RX) /*!< Remap USART6 Rx on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_USART7_RX    (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_USART7_RX) /*!< Remap USART7 Rx on DMA1 channel 6 */ 
+#define HAL_DMA1_CH6_USART8_RX    (uint32_t) (DMA1_CHANNEL6_RMP | DMA1_CSELR_CH6_USART8_RX) /*!< Remap USART8 Rx on DMA1 channel 6 */ 
+/* DMA1 - Channel 7 */
+#define HAL_DMA1_CH7_DEFAULT      (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_DEFAULT)       /*!< Default remap position for DMA1 */   
+#define HAL_DMA1_CH7_I2C1_RX      (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_I2C1_RX)   /*!< Remap I2C1 Rx on DMA1 channel 7 */ 
+#define HAL_DMA1_CH7_SPI2_TX      (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_SPI2_TX)   /*!< Remap SPI2 Tx on DMA1 channel 7 */ 
+#define HAL_DMA1_CH7_TIM2_CH2     (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_TIM2_CH2)  /*!< Remap TIM2 channel 2 on DMA1 channel 7 */
+#define HAL_DMA1_CH7_TIM2_CH4     (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_TIM2_CH4)  /*!< Remap TIM2 channel 4 on DMA1 channel 7 */
+#define HAL_DMA1_CH7_TIM17_CH1    (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_TIM17_CH1) /*!< Remap TIM17 channel 1 on DMA1 channel 7 */
+#define HAL_DMA1_CH7_TIM17_UP     (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_TIM17_UP)  /*!< Remap TIM17 up on DMA1 channel 7 */ 
+#define HAL_DMA1_CH7_USART1_TX    (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_USART1_TX) /*!< Remap USART1 Tx on DMA1 channel 7 */ 
+#define HAL_DMA1_CH7_USART2_TX    (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_USART2_TX) /*!< Remap USART2 Tx on DMA1 channel 7 */ 
+#define HAL_DMA1_CH7_USART3_TX    (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_USART3_TX) /*!< Remap USART3 Tx on DMA1 channel 7 */ 
+#define HAL_DMA1_CH7_USART4_TX    (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_USART4_TX) /*!< Remap USART4 Tx on DMA1 channel 7 */ 
+#define HAL_DMA1_CH7_USART5_TX    (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_USART5_TX) /*!< Remap USART5 Tx on DMA1 channel 7 */ 
+#define HAL_DMA1_CH7_USART6_TX    (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_USART6_TX) /*!< Remap USART6 Tx on DMA1 channel 7 */ 
+#define HAL_DMA1_CH7_USART7_TX    (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_USART7_TX) /*!< Remap USART7 Tx on DMA1 channel 7 */ 
+#define HAL_DMA1_CH7_USART8_TX    (uint32_t) (DMA1_CHANNEL7_RMP | DMA1_CSELR_CH7_USART8_TX) /*!< Remap USART8 Tx on DMA1 channel 7 */
+
+/****************** DMA2 remap bit field definition********************/
+/* DMA2 - Channel 1 */
+#define HAL_DMA2_CH1_DEFAULT      (uint32_t) (DMA2_CHANNEL1_RMP | DMA2_CSELR_DEFAULT)       /*!< Default remap position for DMA2 */   
+#define HAL_DMA2_CH1_I2C2_TX      (uint32_t) (DMA2_CHANNEL1_RMP | DMA2_CSELR_CH1_I2C2_TX)   /*!< Remap I2C2 TX on DMA2 channel 1 */ 
+#define HAL_DMA2_CH1_USART1_TX    (uint32_t) (DMA2_CHANNEL1_RMP | DMA2_CSELR_CH1_USART1_TX) /*!< Remap USART1 Tx on DMA2 channel 1 */ 
+#define HAL_DMA2_CH1_USART2_TX    (uint32_t) (DMA2_CHANNEL1_RMP | DMA2_CSELR_CH1_USART2_TX) /*!< Remap USART2 Tx on DMA2 channel 1 */ 
+#define HAL_DMA2_CH1_USART3_TX    (uint32_t) (DMA2_CHANNEL1_RMP | DMA2_CSELR_CH1_USART3_TX) /*!< Remap USART3 Tx on DMA2 channel 1 */ 
+#define HAL_DMA2_CH1_USART4_TX    (uint32_t) (DMA2_CHANNEL1_RMP | DMA2_CSELR_CH1_USART4_TX) /*!< Remap USART4 Tx on DMA2 channel 1 */ 
+#define HAL_DMA2_CH1_USART5_TX    (uint32_t) (DMA2_CHANNEL1_RMP | DMA2_CSELR_CH1_USART5_TX) /*!< Remap USART5 Tx on DMA2 channel 1 */ 
+#define HAL_DMA2_CH1_USART6_TX    (uint32_t) (DMA2_CHANNEL1_RMP | DMA2_CSELR_CH1_USART6_TX) /*!< Remap USART6 Tx on DMA2 channel 1 */ 
+#define HAL_DMA2_CH1_USART7_TX    (uint32_t) (DMA2_CHANNEL1_RMP | DMA2_CSELR_CH1_USART7_TX) /*!< Remap USART7 Tx on DMA2 channel 1 */ 
+#define HAL_DMA2_CH1_USART8_TX    (uint32_t) (DMA2_CHANNEL1_RMP | DMA2_CSELR_CH1_USART8_TX) /*!< Remap USART8 Tx on DMA2 channel 1 */ 
+/* DMA2 - Channel 2 */
+#define HAL_DMA2_CH2_DEFAULT      (uint32_t) (DMA2_CHANNEL2_RMP | DMA2_CSELR_DEFAULT)       /*!< Default remap position for DMA2 */   
+#define HAL_DMA2_CH2_I2C2_RX      (uint32_t) (DMA2_CHANNEL2_RMP | DMA2_CSELR_CH2_I2C2_RX)   /*!< Remap I2C2 Rx on DMA2 channel 2 */ 
+#define HAL_DMA2_CH2_USART1_RX    (uint32_t) (DMA2_CHANNEL2_RMP | DMA2_CSELR_CH2_USART1_RX) /*!< Remap USART1 Rx on DMA2 channel 2 */ 
+#define HAL_DMA2_CH2_USART2_RX    (uint32_t) (DMA2_CHANNEL2_RMP | DMA2_CSELR_CH2_USART2_RX) /*!< Remap USART2 Rx on DMA2 channel 2 */ 
+#define HAL_DMA2_CH2_USART3_RX    (uint32_t) (DMA2_CHANNEL2_RMP | DMA2_CSELR_CH2_USART3_RX) /*!< Remap USART3 Rx on DMA2 channel 2 */ 
+#define HAL_DMA2_CH2_USART4_RX    (uint32_t) (DMA2_CHANNEL2_RMP | DMA2_CSELR_CH2_USART4_RX) /*!< Remap USART4 Rx on DMA2 channel 2 */ 
+#define HAL_DMA2_CH2_USART5_RX    (uint32_t) (DMA2_CHANNEL2_RMP | DMA2_CSELR_CH2_USART5_RX) /*!< Remap USART5 Rx on DMA2 channel 2 */ 
+#define HAL_DMA2_CH2_USART6_RX    (uint32_t) (DMA2_CHANNEL2_RMP | DMA2_CSELR_CH2_USART6_RX) /*!< Remap USART6 Rx on DMA2 channel 2 */ 
+#define HAL_DMA2_CH2_USART7_RX    (uint32_t) (DMA2_CHANNEL2_RMP | DMA2_CSELR_CH2_USART7_RX) /*!< Remap USART7 Rx on DMA2 channel 2 */ 
+#define HAL_DMA2_CH2_USART8_RX    (uint32_t) (DMA2_CHANNEL2_RMP | DMA2_CSELR_CH2_USART8_RX) /*!< Remap USART8 Rx on DMA2 channel 2 */ 
+/* DMA2 - Channel 3 */
+#define HAL_DMA2_CH3_DEFAULT      (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_DEFAULT)       /*!< Default remap position for DMA2 */   
+#define HAL_DMA2_CH3_TIM6_UP      (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_TIM6_UP)   /*!< Remap TIM6 up on DMA2 channel 3 */ 
+#define HAL_DMA2_CH3_DAC_CH1      (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_DAC_CH1)   /*!< Remap DAC channel 1 on DMA2 channel 3 */
+#define HAL_DMA2_CH3_SPI1_RX      (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_SPI1_RX)   /*!< Remap SPI1 Rx on DMA2 channel 3 */ 
+#define HAL_DMA2_CH3_USART1_RX    (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_USART1_RX) /*!< Remap USART1 Rx on DMA2 channel 3 */ 
+#define HAL_DMA2_CH3_USART2_RX    (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_USART2_RX) /*!< Remap USART2 Rx on DMA2 channel 3 */ 
+#define HAL_DMA2_CH3_USART3_RX    (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_USART3_RX) /*!< Remap USART3 Rx on DMA2 channel 3 */ 
+#define HAL_DMA2_CH3_USART4_RX    (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_USART4_RX) /*!< Remap USART4 Rx on DMA2 channel 3 */ 
+#define HAL_DMA2_CH3_USART5_RX    (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_USART5_RX) /*!< Remap USART5 Rx on DMA2 channel 3 */ 
+#define HAL_DMA2_CH3_USART6_RX    (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_USART6_RX) /*!< Remap USART6 Rx on DMA2 channel 3 */ 
+#define HAL_DMA2_CH3_USART7_RX    (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_USART7_RX) /*!< Remap USART7 Rx on DMA2 channel 3 */ 
+#define HAL_DMA2_CH3_USART8_RX    (uint32_t) (DMA2_CHANNEL3_RMP | DMA2_CSELR_CH3_USART8_RX) /*!< Remap USART8 Rx on DMA2 channel 3 */ 
+/* DMA2 - Channel 4 */
+#define HAL_DMA2_CH4_DEFAULT      (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_DEFAULT)       /*!< Default remap position for DMA2 */   
+#define HAL_DMA2_CH4_TIM7_UP      (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_TIM7_UP)   /*!< Remap TIM7 up on DMA2 channel 4 */ 
+#define HAL_DMA2_CH4_DAC_CH2      (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_DAC_CH2)   /*!< Remap DAC channel 2 on DMA2 channel 4 */
+#define HAL_DMA2_CH4_SPI1_TX      (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_SPI1_TX)   /*!< Remap SPI1 Tx on DMA2 channel 4 */ 
+#define HAL_DMA2_CH4_USART1_TX    (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_USART1_TX) /*!< Remap USART1 Tx on DMA2 channel 4 */ 
+#define HAL_DMA2_CH4_USART2_TX    (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_USART2_TX) /*!< Remap USART2 Tx on DMA2 channel 4 */ 
+#define HAL_DMA2_CH4_USART3_TX    (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_USART3_TX) /*!< Remap USART3 Tx on DMA2 channel 4 */ 
+#define HAL_DMA2_CH4_USART4_TX    (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_USART4_TX) /*!< Remap USART4 Tx on DMA2 channel 4 */ 
+#define HAL_DMA2_CH4_USART5_TX    (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_USART5_TX) /*!< Remap USART5 Tx on DMA2 channel 4 */ 
+#define HAL_DMA2_CH4_USART6_TX    (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_USART6_TX) /*!< Remap USART6 Tx on DMA2 channel 4 */ 
+#define HAL_DMA2_CH4_USART7_TX    (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_USART7_TX) /*!< Remap USART7 Tx on DMA2 channel 4 */ 
+#define HAL_DMA2_CH4_USART8_TX    (uint32_t) (DMA2_CHANNEL4_RMP | DMA2_CSELR_CH4_USART8_TX) /*!< Remap USART8 Tx on DMA2 channel 4 */ 
+/* DMA2 - Channel 5 */
+#define HAL_DMA2_CH5_DEFAULT      (uint32_t) (DMA2_CHANNEL5_RMP | DMA2_CSELR_DEFAULT)       /*!< Default remap position for DMA2 */   
+#define HAL_DMA2_CH5_ADC          (uint32_t) (DMA2_CHANNEL5_RMP | DMA2_CSELR_CH5_ADC)       /*!< Remap ADC on DMA2 channel 5 */  
+#define HAL_DMA2_CH5_USART1_TX    (uint32_t) (DMA2_CHANNEL5_RMP | DMA2_CSELR_CH5_USART1_TX) /*!< Remap USART1 Tx on DMA2 channel 5 */ 
+#define HAL_DMA2_CH5_USART2_TX    (uint32_t) (DMA2_CHANNEL5_RMP | DMA2_CSELR_CH5_USART2_TX) /*!< Remap USART2 Tx on DMA2 channel 5 */ 
+#define HAL_DMA2_CH5_USART3_TX    (uint32_t) (DMA2_CHANNEL5_RMP | DMA2_CSELR_CH5_USART3_TX) /*!< Remap USART3 Tx on DMA2 channel 5 */ 
+#define HAL_DMA2_CH5_USART4_TX    (uint32_t) (DMA2_CHANNEL5_RMP | DMA2_CSELR_CH5_USART4_TX) /*!< Remap USART4 Tx on DMA2 channel 5 */ 
+#define HAL_DMA2_CH5_USART5_TX    (uint32_t) (DMA2_CHANNEL5_RMP | DMA2_CSELR_CH5_USART5_TX) /*!< Remap USART5 Tx on DMA2 channel 5 */ 
+#define HAL_DMA2_CH5_USART6_TX    (uint32_t) (DMA2_CHANNEL5_RMP | DMA2_CSELR_CH5_USART6_TX) /*!< Remap USART6 Tx on DMA2 channel 5 */ 
+#define HAL_DMA2_CH5_USART7_TX    (uint32_t) (DMA2_CHANNEL5_RMP | DMA2_CSELR_CH5_USART7_TX) /*!< Remap USART7 Tx on DMA2 channel 5 */ 
+#define HAL_DMA2_CH5_USART8_TX    (uint32_t) (DMA2_CHANNEL5_RMP | DMA2_CSELR_CH5_USART8_TX) /*!< Remap USART8 Tx on DMA2 channel 5 */ 
+#endif /* !defined(STM32F030xC) */
+
+#if defined(STM32F091xC) || defined(STM32F098xx) 
+#define IS_HAL_DMA1_REMAP(REQUEST)  (((REQUEST) == HAL_DMA1_CH1_DEFAULT)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_ADC)       ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_TIM17_CH1) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_TIM17_UP)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART1_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART2_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART3_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART4_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART5_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART6_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART7_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART8_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_ADC)       ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_I2C1_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_SPI1_RX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_TIM1_CH1)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_I2C1_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_TIM17_CH1) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_TIM17_UP)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART1_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART2_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART3_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART4_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART5_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART6_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART7_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART8_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_TIM6_UP)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_DAC_CH1)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_I2C1_RX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_SPI1_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_TIM1_CH2)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_TIM2_CH2)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_TIM16_CH1) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_TIM16_UP)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART1_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART2_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART3_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART4_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART5_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART6_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART7_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART8_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM7_UP)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_DAC_CH2)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_I2C2_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_SPI2_RX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM2_CH4)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM3_CH1)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM3_TRIG) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM16_CH1) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM16_UP)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART1_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART2_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART3_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART4_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART5_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART6_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART7_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART8_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_I2C2_RX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_SPI2_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_TIM1_CH3)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART1_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART2_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART3_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART4_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART5_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART6_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART7_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART8_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_I2C1_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_SPI2_RX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_TIM1_CH1)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_TIM1_CH2)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_TIM1_CH3)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_TIM3_CH1)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_TIM3_TRIG) ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_TIM16_CH1) ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_TIM16_UP)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_USART1_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_USART2_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_USART3_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_USART4_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_USART5_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_USART6_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_USART7_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH6_USART8_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_I2C1_RX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_SPI2_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_TIM2_CH2)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_TIM2_CH4)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_TIM17_CH1) ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_TIM17_UP)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_USART1_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_USART2_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_USART3_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_USART4_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_USART5_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_USART6_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_USART7_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH7_USART8_TX))
+
+#define IS_HAL_DMA2_REMAP(REQUEST)  (((REQUEST) == HAL_DMA2_CH1_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH1_I2C2_TX)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH1_USART1_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH1_USART2_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH1_USART3_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH1_USART4_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH1_USART5_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH1_USART6_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH1_USART7_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH1_USART8_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH2_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH2_I2C2_RX)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH2_USART1_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH2_USART2_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH2_USART3_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH2_USART4_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH2_USART5_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH2_USART6_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH2_USART7_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH2_USART8_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_TIM6_UP)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_DAC_CH1)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_SPI1_RX)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_USART1_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_USART2_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_USART3_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_USART4_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_USART5_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_USART6_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_USART7_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH3_USART8_RX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_TIM7_UP)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_DAC_CH2)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_SPI1_TX)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_USART1_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_USART2_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_USART3_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_USART4_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_USART5_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_USART6_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_USART7_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH4_USART8_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH5_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA2_CH5_ADC)       ||\
+                                    ((REQUEST) == HAL_DMA2_CH5_USART1_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH5_USART2_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH5_USART3_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH5_USART4_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH5_USART5_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH5_USART6_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH5_USART7_TX) ||\
+                                    ((REQUEST) == HAL_DMA2_CH5_USART8_TX ))
+#endif /* STM32F091xC || STM32F098xx */
+
+#if defined(STM32F030xC)
+#define IS_HAL_DMA1_REMAP(REQUEST)  (((REQUEST) == HAL_DMA1_CH1_DEFAULT)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_ADC)       ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_TIM17_CH1) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_TIM17_UP)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART1_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART2_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART3_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART4_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART5_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH1_USART6_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_ADC)       ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_I2C1_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_SPI1_RX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_TIM1_CH1)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_I2C1_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_TIM17_CH1) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_TIM17_UP)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART1_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART2_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART3_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART4_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART5_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH2_USART6_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_TIM6_UP)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_I2C1_RX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_SPI1_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_TIM1_CH2)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_TIM16_CH1) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_TIM16_UP)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART1_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART2_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART3_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART4_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART5_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH3_USART6_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM7_UP)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_I2C2_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_SPI2_RX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM3_CH1)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM3_TRIG) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM16_CH1) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_TIM16_UP)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART1_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART2_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART3_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART4_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART5_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH4_USART6_TX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_DEFAULT)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_I2C2_RX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_SPI2_TX)   ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_TIM1_CH3)  ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART1_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART2_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART3_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART4_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART5_RX) ||\
+                                    ((REQUEST) == HAL_DMA1_CH5_USART6_RX))
+#endif /* STM32F030xC */
+
+/**
+  * @}
+  */ 
+#endif /* STM32F091xC  || STM32F098xx || STM32F030xC */
+
+/* Exported macros -----------------------------------------------------------*/
+
+/** @defgroup DMAEx_Exported_Macros DMAEx Exported Macros
+  * @{
+  */
+/* Interrupt & Flag management */
+
+#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx)
+/**
+  * @brief  Returns the current DMA Channel transfer complete flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer complete flag index.
+  */      
+#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TC1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TC2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TC3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TC4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TC5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TC6 :\
+   DMA_FLAG_TC7)
+
+/**
+  * @brief  Returns the current DMA Channel half transfer complete flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified half transfer complete flag index.
+  */      
+#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_HT1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_HT2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_HT3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_HT4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_HT5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_HT6 :\
+   DMA_FLAG_HT7)
+
+/**
+  * @brief  Returns the current DMA Channel transfer error flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TE1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TE2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TE3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TE4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TE5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TE6 :\
+   DMA_FLAG_TE7)
+
+/**
+  * @brief  Return the current DMA Channel Global interrupt flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#define __HAL_DMA_GET_GI_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_GL1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_GL2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_GL3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_GL4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_GL5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_GL6 :\
+   DMA_FLAG_GL7)
+
+/**
+  * @brief  Get the DMA Channel pending flags.
+  * @param  __HANDLE__ DMA handle
+  * @param  __FLAG__ Get the specified flag.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *         Where x can be 1_7 to select the DMA Channel flag.   
+  * @retval The state of FLAG (SET or RESET).
+  */
+
+#define __HAL_DMA_GET_FLAG(__HANDLE__, __FLAG__)   (DMA1->ISR & (__FLAG__))
+
+/**
+  * @brief  Clears the DMA Channel pending flags.
+  * @param  __HANDLE__ DMA handle
+  * @param  __FLAG__ specifies the flag to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *         Where x can be 1_7 to select the DMA Channel flag.   
+  * @retval None
+  */
+#define __HAL_DMA_CLEAR_FLAG(__HANDLE__, __FLAG__) (DMA1->IFCR = (__FLAG__))
+
+#elif defined(STM32F091xC) || defined(STM32F098xx)
+/**
+  * @brief  Returns the current DMA Channel transfer complete flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer complete flag index.
+  */      
+#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TC1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TC2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TC3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TC4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TC5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TC6 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_TC7 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_TC1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_TC2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_TC3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_TC4 :\
+   DMA_FLAG_TC5)
+
+/**
+  * @brief  Returns the current DMA Channel half transfer complete flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified half transfer complete flag index.
+  */      
+#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_HT1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_HT2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_HT3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_HT4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_HT5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_HT6 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_HT7 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_HT1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_HT2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_HT3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_HT4 :\
+   DMA_FLAG_HT5)
+
+/**
+  * @brief  Returns the current DMA Channel transfer error flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TE1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TE2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TE3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TE4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TE5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TE6 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_TE7 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_TE1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_TE2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_TE3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_TE4 :\
+   DMA_FLAG_TE5)
+
+/**
+  * @brief  Return the current DMA Channel Global interrupt flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#define __HAL_DMA_GET_GI_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_GL1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_GL2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_GL3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_GL4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_GL5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_GL6 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_GL7 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_GL1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_GL2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_GL3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_GL4 :\
+   DMA_FLAG_GL5)
+
+/**
+  * @brief  Get the DMA Channel pending flags.
+  * @param  __HANDLE__ DMA handle
+  * @param  __FLAG__ Get the specified flag.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *         Where x can be 0_4, 1_5, 2_6 or 3_7 to select the DMA Channel flag.   
+  * @retval The state of FLAG (SET or RESET).
+  */
+
+#define __HAL_DMA_GET_FLAG(__HANDLE__, __FLAG__)\
+(((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Channel7)? (DMA2->ISR & (__FLAG__)) :\
+  (DMA1->ISR & (__FLAG__)))
+
+/**
+  * @brief  Clears the DMA Channel pending flags.
+  * @param  __HANDLE__ DMA handle
+  * @param  __FLAG__ specifies the flag to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *         Where x can be 0_4, 1_5, 2_6 or 3_7 to select the DMA Channel flag.   
+  * @retval None
+  */
+#define __HAL_DMA_CLEAR_FLAG(__HANDLE__, __FLAG__) \
+(((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Channel7)? (DMA2->IFCR = (__FLAG__)) :\
+  (DMA1->IFCR = (__FLAG__)))
+
+#else /* STM32F030x8_STM32F030xC_STM32F031x6_STM32F038xx_STM32F051x8_STM32F058xx_STM32F070x6_STM32F070xB Product devices */
+/**
+  * @brief  Returns the current DMA Channel transfer complete flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer complete flag index.
+  */      
+#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TC1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TC2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TC3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TC4 :\
+   DMA_FLAG_TC5)
+
+/**
+  * @brief  Returns the current DMA Channel half transfer complete flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified half transfer complete flag index.
+  */      
+#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_HT1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_HT2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_HT3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_HT4 :\
+   DMA_FLAG_HT5)
+
+/**
+  * @brief  Returns the current DMA Channel transfer error flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TE1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TE2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TE3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TE4 :\
+   DMA_FLAG_TE5)
+
+/**
+  * @brief  Return the current DMA Channel Global interrupt flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#define __HAL_DMA_GET_GI_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_GL1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_GL2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_GL3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_GL4 :\
+   DMA_FLAG_GL5)
+
+/**
+  * @brief  Get the DMA Channel pending flags.
+  * @param  __HANDLE__ DMA handle
+  * @param  __FLAG__ Get the specified flag.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *         Where x can be 1_5 to select the DMA Channel flag.   
+  * @retval The state of FLAG (SET or RESET).
+  */
+
+#define __HAL_DMA_GET_FLAG(__HANDLE__, __FLAG__)   (DMA1->ISR & (__FLAG__))
+
+/**
+  * @brief  Clears the DMA Channel pending flags.
+  * @param  __HANDLE__ DMA handle
+  * @param  __FLAG__ specifies the flag to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *         Where x can be 1_5 to select the DMA Channel flag.   
+  * @retval None
+  */
+#define __HAL_DMA_CLEAR_FLAG(__HANDLE__, __FLAG__) (DMA1->IFCR = (__FLAG__))
+
+#endif
+
+
+#if defined(STM32F091xC) || defined(STM32F098xx) || defined(STM32F030xC)
+#define __HAL_DMA1_REMAP(__REQUEST__)                                                              \
+         do { assert_param(IS_HAL_DMA1_REMAP(__REQUEST__));                                             \
+              DMA1->CSELR &= ~(0x0FU << (uint32_t)(((__REQUEST__) >> 28U) * 4U)); \
+              DMA1->CSELR |= (uint32_t)((__REQUEST__) & 0x0FFFFFFFU);                                     \
+  }while(0)
+
+#if defined(STM32F091xC) || defined(STM32F098xx)
+#define __HAL_DMA2_REMAP(__REQUEST__)                                                              \
+         do { assert_param(IS_HAL_DMA2_REMAP(__REQUEST__));                                             \
+              DMA2->CSELR &= ~(0x0FU << (uint32_t)(((__REQUEST__) >> 28U) * 4U)); \
+              DMA2->CSELR |= (uint32_t)((__REQUEST__) & 0x0FFFFFFFU);                                     \
+         }while(0)
+#endif /* STM32F091xC || STM32F098xx */
+
+#endif /* STM32F091xC || STM32F098xx || STM32F030xC */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_DMA_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_exti.h

@@ -0,0 +1,375 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_exti.h
+  * @author  MCD Application Team
+  * @brief   Header file of EXTI HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F0xx_HAL_EXTI_H
+#define STM32F0xx_HAL_EXTI_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup EXTI EXTI
+  * @brief EXTI HAL module driver
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup EXTI_Exported_Types EXTI Exported Types
+  * @{
+  */
+
+/**
+  * @brief  HAL EXTI common Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_EXTI_COMMON_CB_ID          = 0x00U
+} EXTI_CallbackIDTypeDef;
+
+/**
+  * @brief  EXTI Handle structure definition
+  */
+typedef struct
+{
+  uint32_t Line;                    /*!<  Exti line number */
+  void (* PendingCallback)(void);   /*!<  Exti pending callback */
+} EXTI_HandleTypeDef;
+
+/**
+  * @brief  EXTI Configuration structure definition
+  */
+typedef struct
+{
+  uint32_t Line;      /*!< The Exti line to be configured. This parameter
+                           can be a value of @ref EXTI_Line */
+  uint32_t Mode;      /*!< The Exit Mode to be configured for a core.
+                           This parameter can be a combination of @ref EXTI_Mode */
+  uint32_t Trigger;   /*!< The Exti Trigger to be configured. This parameter
+                           can be a value of @ref EXTI_Trigger */
+  uint32_t GPIOSel;   /*!< The Exti GPIO multiplexer selection to be configured.
+                           This parameter is only possible for line 0 to 15. It
+                           can be a value of @ref EXTI_GPIOSel */
+} EXTI_ConfigTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup EXTI_Exported_Constants EXTI Exported Constants
+  * @{
+  */
+
+/** @defgroup EXTI_Line  EXTI Line
+  * @{
+  */
+#define EXTI_LINE_0                        (EXTI_GPIO        | 0x00u)    /*!< External interrupt line 0 */
+#define EXTI_LINE_1                        (EXTI_GPIO        | 0x01u)    /*!< External interrupt line 1 */
+#define EXTI_LINE_2                        (EXTI_GPIO        | 0x02u)    /*!< External interrupt line 2 */
+#define EXTI_LINE_3                        (EXTI_GPIO        | 0x03u)    /*!< External interrupt line 3 */
+#define EXTI_LINE_4                        (EXTI_GPIO        | 0x04u)    /*!< External interrupt line 4 */
+#define EXTI_LINE_5                        (EXTI_GPIO        | 0x05u)    /*!< External interrupt line 5 */
+#define EXTI_LINE_6                        (EXTI_GPIO        | 0x06u)    /*!< External interrupt line 6 */
+#define EXTI_LINE_7                        (EXTI_GPIO        | 0x07u)    /*!< External interrupt line 7 */
+#define EXTI_LINE_8                        (EXTI_GPIO        | 0x08u)    /*!< External interrupt line 8 */
+#define EXTI_LINE_9                        (EXTI_GPIO        | 0x09u)    /*!< External interrupt line 9 */
+#define EXTI_LINE_10                       (EXTI_GPIO        | 0x0Au)    /*!< External interrupt line 10 */
+#define EXTI_LINE_11                       (EXTI_GPIO        | 0x0Bu)    /*!< External interrupt line 11 */
+#define EXTI_LINE_12                       (EXTI_GPIO        | 0x0Cu)    /*!< External interrupt line 12 */
+#define EXTI_LINE_13                       (EXTI_GPIO        | 0x0Du)    /*!< External interrupt line 13 */
+#define EXTI_LINE_14                       (EXTI_GPIO        | 0x0Eu)    /*!< External interrupt line 14 */
+#define EXTI_LINE_15                       (EXTI_GPIO        | 0x0Fu)    /*!< External interrupt line 15 */
+
+#if defined (EXTI_IMR_MR16)
+#define EXTI_LINE_16                       (EXTI_CONFIG      | 0x10u)    /*!< External interrupt line 16 Connected to the PVD Output */
+#else
+#define EXTI_LINE_16                       (EXTI_RESERVED    | 0x10u)
+#endif /* EXTI_IMR_MR16 */
+
+#define EXTI_LINE_17                       (EXTI_CONFIG      | 0x11u)    /*!< External interrupt line 17 Connected to the RTC Alarm event */
+
+#if defined (EXTI_IMR_MR18)
+#define EXTI_LINE_18                       (EXTI_CONFIG      | 0x12u)    /*!< External interrupt line 18 Connected to the USB OTG FS Wakeup from suspend event */
+#else
+#define EXTI_LINE_18                       (EXTI_RESERVED    | 0x12u)
+#endif /* EXTI_IMR_MR18 */
+
+#define EXTI_LINE_19                       (EXTI_CONFIG      | 0x13u)    /*!< External interrupt line 19 Connected to the Ethernet Wakeup event */
+
+#if defined (EXTI_IMR_MR20)
+#define EXTI_LINE_20                       (EXTI_CONFIG      | 0x14u)    /*!< External interrupt line 20 Connected to the USB OTG HS (configured in FS) Wakeup event  */
+#else
+#define EXTI_LINE_20                       (EXTI_RESERVED    | 0x14u)
+#endif /* EXTI_IMR_MR20 */
+
+#if defined (EXTI_IMR_MR21)
+#define EXTI_LINE_21                       (EXTI_CONFIG      | 0x15u)    /*!< External interrupt line 21 Connected to the Comparator 1 output */
+#else
+#define EXTI_LINE_21                       (EXTI_RESERVED    | 0x15u)
+#endif /* EXTI_IMR_MR21 */
+
+#if defined (EXTI_IMR_MR22)
+#define EXTI_LINE_22                       (EXTI_CONFIG      | 0x16u)    /*!< External interrupt line 22 Connected to the Comparator 2 output */
+#else
+#define EXTI_LINE_22                       (EXTI_RESERVED    | 0x16u)
+#endif /* EXTI_IMR_MR22 */
+
+#if defined (EXTI_IMR_MR23)
+#define EXTI_LINE_23                       (EXTI_DIRECT      | 0x17u)    /*!< External interrupt line 23 Connected to the internal I2C1 wakeup event  */
+#else
+#define EXTI_LINE_23                       (EXTI_RESERVED    | 0x17u)
+#endif /* EXTI_IMR_MR23 */
+
+#define EXTI_LINE_24                       (EXTI_RESERVED    | 0x18u)
+
+#if defined (EXTI_IMR_MR25)
+#define EXTI_LINE_25                       (EXTI_CONFIG      | 0x19u)    /*!< External interrupt line 25 Connected to the internal USART1 wakeup event  */
+#else
+#define EXTI_LINE_25                       (EXTI_RESERVED    | 0x19u)
+#endif /* EXTI_IMR_MR25 */
+
+#if defined (EXTI_IMR_MR26)
+#define EXTI_LINE_26                       (EXTI_CONFIG      | 0x1Au)    /*!< External interrupt line 26 Connected to the internal USART2 wakeup event  */
+#else
+#define EXTI_LINE_26                       (EXTI_RESERVED    | 0x1Au)
+#endif /* EXTI_IMR_MR26 */
+
+#if defined (EXTI_IMR_MR27)
+#define EXTI_LINE_27                       (EXTI_CONFIG      | 0x1Bu)    /*!< External interrupt line 27 Connected to the internal CEC wakeup event  */
+#else
+#define EXTI_LINE_27                       (EXTI_RESERVED    | 0x1Bu)
+#endif /* EXTI_IMR_MR27 */
+
+#if defined (EXTI_IMR_MR28)
+#define EXTI_LINE_28                       (EXTI_CONFIG      | 0x1Cu)    /*!< External interrupt line 28 Connected to the  internal USART3 wakeup event   */
+#else
+#define EXTI_LINE_28                       (EXTI_RESERVED    | 0x1Cu)
+#endif /* EXTI_IMR_MR28 */
+
+#define EXTI_LINE_29                       (EXTI_RESERVED    | 0x1Du)
+#define EXTI_LINE_30                       (EXTI_RESERVED    | 0x1Eu)
+
+#if defined (EXTI_IMR_MR31)
+#define EXTI_LINE_31                       (EXTI_CONFIG      | 0x1Fu)    /*!< External interrupt line 31 Connected to the VDDIO2 supply comparator output  */
+#else
+#define EXTI_LINE_31                       (EXTI_RESERVED    | 0x1Fu)
+#endif /* EXTI_IMR_MR31 */
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Mode  EXTI Mode
+  * @{
+  */
+#define EXTI_MODE_NONE                      0x00000000u
+#define EXTI_MODE_INTERRUPT                 0x00000001u
+#define EXTI_MODE_EVENT                     0x00000002u
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Trigger  EXTI Trigger
+  * @{
+  */
+#define EXTI_TRIGGER_NONE                   0x00000000u
+#define EXTI_TRIGGER_RISING                 0x00000001u
+#define EXTI_TRIGGER_FALLING                0x00000002u
+#define EXTI_TRIGGER_RISING_FALLING         (EXTI_TRIGGER_RISING | EXTI_TRIGGER_FALLING)
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_GPIOSel  EXTI GPIOSel
+  * @brief
+  * @{
+  */
+#define EXTI_GPIOA                          0x00000000u
+#define EXTI_GPIOB                          0x00000001u
+#define EXTI_GPIOC                          0x00000002u
+#if defined (GPIOD)
+#define EXTI_GPIOD                          0x00000003u
+#endif /* GPIOD */
+#if defined (GPIOE)
+#define EXTI_GPIOE                          0x00000004u
+#endif /* GPIOE */
+#define EXTI_GPIOF                          0x00000005u
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup EXTI_Exported_Macros EXTI Exported Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private constants --------------------------------------------------------*/
+/** @defgroup EXTI_Private_Constants EXTI Private Constants
+  * @{
+  */
+/**
+  * @brief  EXTI Line property definition
+  */
+#define EXTI_PROPERTY_SHIFT                 24u
+#define EXTI_DIRECT                         (0x01uL << EXTI_PROPERTY_SHIFT)
+#define EXTI_CONFIG                         (0x02uL << EXTI_PROPERTY_SHIFT)
+#define EXTI_GPIO                           ((0x04uL << EXTI_PROPERTY_SHIFT) | EXTI_CONFIG)
+#define EXTI_RESERVED                       (0x08uL << EXTI_PROPERTY_SHIFT)
+#define EXTI_PROPERTY_MASK                  (EXTI_DIRECT | EXTI_CONFIG | EXTI_GPIO)
+
+/**
+  * @brief  EXTI bit usage
+  */
+#define EXTI_PIN_MASK                       0x0000001Fu
+
+/**
+  * @brief  EXTI Mask for interrupt & event mode
+  */
+#define EXTI_MODE_MASK                      (EXTI_MODE_EVENT | EXTI_MODE_INTERRUPT)
+
+/**
+  * @brief  EXTI Mask for trigger possibilities
+  */
+#define EXTI_TRIGGER_MASK                   (EXTI_TRIGGER_RISING | EXTI_TRIGGER_FALLING)
+
+/**
+  * @brief  EXTI Line number
+  */
+#define EXTI_LINE_NB                        32uL
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup EXTI_Private_Macros EXTI Private Macros
+  * @{
+  */
+#define IS_EXTI_LINE(__EXTI_LINE__)          ((((__EXTI_LINE__) & ~(EXTI_PROPERTY_MASK | EXTI_PIN_MASK)) == 0x00u) && \
+                                             ((((__EXTI_LINE__) & EXTI_PROPERTY_MASK) == EXTI_DIRECT)   || \
+                                              (((__EXTI_LINE__) & EXTI_PROPERTY_MASK) == EXTI_CONFIG)   || \
+                                              (((__EXTI_LINE__) & EXTI_PROPERTY_MASK) == EXTI_GPIO))    && \
+                                              (((__EXTI_LINE__) & EXTI_PIN_MASK) < EXTI_LINE_NB))
+
+#define IS_EXTI_MODE(__EXTI_LINE__)          ((((__EXTI_LINE__) & EXTI_MODE_MASK) != 0x00u) && \
+                                              (((__EXTI_LINE__) & ~EXTI_MODE_MASK) == 0x00u))
+
+#define IS_EXTI_TRIGGER(__EXTI_LINE__)       (((__EXTI_LINE__) & ~EXTI_TRIGGER_MASK) == 0x00u)
+
+#define IS_EXTI_PENDING_EDGE(__EXTI_LINE__)  ((__EXTI_LINE__) == EXTI_TRIGGER_RISING_FALLING)
+
+#define IS_EXTI_CONFIG_LINE(__EXTI_LINE__)   (((__EXTI_LINE__) & EXTI_CONFIG) != 0x00u)
+
+#if defined (GPIOE)
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC) || \
+                                         ((__PORT__) == EXTI_GPIOD) || \
+                                         ((__PORT__) == EXTI_GPIOE) || \
+                                         ((__PORT__) == EXTI_GPIOF))
+#elif defined (GPIOD)
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC) || \
+                                         ((__PORT__) == EXTI_GPIOD) || \
+                                         ((__PORT__) == EXTI_GPIOF))
+#else
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC) || \
+                                         ((__PORT__) == EXTI_GPIOF))
+#endif /* GPIOE */
+
+#define IS_EXTI_GPIO_PIN(__PIN__)       ((__PIN__) < 16u)
+
+/**
+  * @}
+  */
+
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup EXTI_Exported_Functions EXTI Exported Functions
+  * @brief    EXTI Exported Functions
+  * @{
+  */
+
+/** @defgroup EXTI_Exported_Functions_Group1 Configuration functions
+  * @brief    Configuration functions
+  * @{
+  */
+/* Configuration functions ****************************************************/
+HAL_StatusTypeDef HAL_EXTI_SetConfigLine(EXTI_HandleTypeDef *hexti, EXTI_ConfigTypeDef *pExtiConfig);
+HAL_StatusTypeDef HAL_EXTI_GetConfigLine(EXTI_HandleTypeDef *hexti, EXTI_ConfigTypeDef *pExtiConfig);
+HAL_StatusTypeDef HAL_EXTI_ClearConfigLine(EXTI_HandleTypeDef *hexti);
+HAL_StatusTypeDef HAL_EXTI_RegisterCallback(EXTI_HandleTypeDef *hexti, EXTI_CallbackIDTypeDef CallbackID, void (*pPendingCbfn)(void));
+HAL_StatusTypeDef HAL_EXTI_GetHandle(EXTI_HandleTypeDef *hexti, uint32_t ExtiLine);
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Exported_Functions_Group2 IO operation functions
+  * @brief    IO operation functions
+  * @{
+  */
+/* IO operation functions *****************************************************/
+void              HAL_EXTI_IRQHandler(EXTI_HandleTypeDef *hexti);
+uint32_t          HAL_EXTI_GetPending(EXTI_HandleTypeDef *hexti, uint32_t Edge);
+void              HAL_EXTI_ClearPending(EXTI_HandleTypeDef *hexti, uint32_t Edge);
+void              HAL_EXTI_GenerateSWI(EXTI_HandleTypeDef *hexti);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F0xx_HAL_EXTI_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_flash.h

@@ -0,0 +1,353 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_flash.h
+  * @author  MCD Application Team
+  * @brief   Header file of Flash HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_FLASH_H
+#define __STM32F0xx_HAL_FLASH_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+   
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup FLASH
+  * @{
+  */
+  
+/** @addtogroup FLASH_Private_Constants
+  * @{
+  */
+#define FLASH_TIMEOUT_VALUE      (50000U) /* 50 s */
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Private_Macros
+  * @{
+  */
+
+#define IS_FLASH_TYPEPROGRAM(VALUE)  (((VALUE) == FLASH_TYPEPROGRAM_HALFWORD) || \
+                                      ((VALUE) == FLASH_TYPEPROGRAM_WORD)     || \
+                                      ((VALUE) == FLASH_TYPEPROGRAM_DOUBLEWORD))  
+
+#define IS_FLASH_LATENCY(__LATENCY__) (((__LATENCY__) == FLASH_LATENCY_0) || \
+                                       ((__LATENCY__) == FLASH_LATENCY_1))
+
+/**
+  * @}
+  */  
+
+/* Exported types ------------------------------------------------------------*/ 
+/** @defgroup FLASH_Exported_Types FLASH Exported Types
+  * @{
+  */  
+
+/**
+  * @brief  FLASH Procedure structure definition
+  */
+typedef enum 
+{
+  FLASH_PROC_NONE              = 0U, 
+  FLASH_PROC_PAGEERASE         = 1U,
+  FLASH_PROC_MASSERASE         = 2U,
+  FLASH_PROC_PROGRAMHALFWORD   = 3U,
+  FLASH_PROC_PROGRAMWORD       = 4U,
+  FLASH_PROC_PROGRAMDOUBLEWORD = 5U
+} FLASH_ProcedureTypeDef;
+
+/** 
+  * @brief  FLASH handle Structure definition  
+  */
+typedef struct
+{
+  __IO FLASH_ProcedureTypeDef ProcedureOnGoing; /*!< Internal variable to indicate which procedure is ongoing or not in IT context */
+  
+  __IO uint32_t               DataRemaining;    /*!< Internal variable to save the remaining pages to erase or half-word to program in IT context */
+
+  __IO uint32_t               Address;          /*!< Internal variable to save address selected for program or erase */
+
+  __IO uint64_t               Data;             /*!< Internal variable to save data to be programmed */
+
+  HAL_LockTypeDef             Lock;             /*!< FLASH locking object                */
+
+  __IO uint32_t               ErrorCode;        /*!< FLASH error code                    
+                                                     This parameter can be a value of @ref FLASH_Error_Codes  */
+} FLASH_ProcessTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup FLASH_Exported_Constants FLASH Exported Constants
+  * @{
+  */  
+
+/** @defgroup FLASH_Error_Codes FLASH Error Codes
+  * @{
+  */
+
+#define HAL_FLASH_ERROR_NONE      0x00U  /*!< No error */
+#define HAL_FLASH_ERROR_PROG      0x01U  /*!< Programming error */
+#define HAL_FLASH_ERROR_WRP       0x02U  /*!< Write protection error */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Type_Program FLASH Type Program
+  * @{
+  */ 
+#define FLASH_TYPEPROGRAM_HALFWORD   (0x01U)  /*!<Program a half-word (16-bit) at a specified address.*/
+#define FLASH_TYPEPROGRAM_WORD       (0x02U)  /*!<Program a word (32-bit) at a specified address.*/
+#define FLASH_TYPEPROGRAM_DOUBLEWORD (0x03U)  /*!<Program a double word (64-bit) at a specified address*/
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Latency FLASH Latency
+  * @{
+  */ 
+#define FLASH_LATENCY_0            (0x00000000U)    /*!< FLASH Zero Latency cycle */
+#define FLASH_LATENCY_1            FLASH_ACR_LATENCY         /*!< FLASH One Latency cycle */
+
+/**
+  * @}
+  */
+
+
+/** @defgroup FLASH_Flag_definition FLASH Flag definition
+  * @{
+  */ 
+#define FLASH_FLAG_BSY             FLASH_SR_BSY            /*!< FLASH Busy flag                           */ 
+#define FLASH_FLAG_PGERR           FLASH_SR_PGERR          /*!< FLASH Programming error flag    */
+#define FLASH_FLAG_WRPERR          FLASH_SR_WRPERR         /*!< FLASH Write protected error flag          */
+#define FLASH_FLAG_EOP             FLASH_SR_EOP            /*!< FLASH End of Operation flag               */
+/**
+  * @}
+  */
+  
+/** @defgroup FLASH_Interrupt_definition FLASH Interrupt definition
+  * @{
+  */ 
+#define FLASH_IT_EOP               FLASH_CR_EOPIE          /*!< End of FLASH Operation Interrupt source */
+#define FLASH_IT_ERR               FLASH_CR_ERRIE  /*!< Error Interrupt source */
+/**
+  * @}
+  */  
+
+/**
+  * @}
+  */  
+  
+/* Exported macro ------------------------------------------------------------*/
+
+/** @defgroup FLASH_Exported_Macros FLASH Exported Macros
+ *  @brief macros to control FLASH features 
+ *  @{
+ */
+ 
+
+/** @defgroup FLASH_EM_Latency FLASH Latency
+ *  @brief macros to handle FLASH Latency
+ * @{
+ */ 
+  
+/**
+  * @brief  Set the FLASH Latency.
+  * @param  __LATENCY__ FLASH Latency                   
+  *         The value of this parameter depend on device used within the same series
+  * @retval None
+  */ 
+#define __HAL_FLASH_SET_LATENCY(__LATENCY__)    (FLASH->ACR = (FLASH->ACR&(~FLASH_ACR_LATENCY)) | (__LATENCY__))
+
+
+/**
+  * @brief  Get the FLASH Latency.
+  * @retval FLASH Latency                   
+  *         The value of this parameter depend on device used within the same series
+  */ 
+#define __HAL_FLASH_GET_LATENCY()     (READ_BIT((FLASH->ACR), FLASH_ACR_LATENCY))
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Prefetch FLASH Prefetch
+ *  @brief macros to handle FLASH Prefetch buffer
+ * @{
+ */   
+/**
+  * @brief  Enable the FLASH prefetch buffer.
+  * @retval None
+  */ 
+#define __HAL_FLASH_PREFETCH_BUFFER_ENABLE()    (FLASH->ACR |= FLASH_ACR_PRFTBE)
+
+/**
+  * @brief  Disable the FLASH prefetch buffer.
+  * @retval None
+  */
+#define __HAL_FLASH_PREFETCH_BUFFER_DISABLE()   (FLASH->ACR &= (~FLASH_ACR_PRFTBE))
+
+/**
+  * @}
+  */
+  
+/** @defgroup FLASH_Interrupt FLASH Interrupts
+ *  @brief macros to handle FLASH interrupts
+ * @{
+ */ 
+
+/**
+  * @brief  Enable the specified FLASH interrupt.
+  * @param  __INTERRUPT__  FLASH interrupt 
+  *         This parameter can be any combination of the following values:
+  *     @arg @ref FLASH_IT_EOP End of FLASH Operation Interrupt
+  *     @arg @ref FLASH_IT_ERR Error Interrupt    
+  * @retval none
+  */  
+#define __HAL_FLASH_ENABLE_IT(__INTERRUPT__)  SET_BIT((FLASH->CR), (__INTERRUPT__))
+
+/**
+  * @brief  Disable the specified FLASH interrupt.
+  * @param  __INTERRUPT__  FLASH interrupt 
+  *         This parameter can be any combination of the following values:
+  *     @arg @ref FLASH_IT_EOP End of FLASH Operation Interrupt
+  *     @arg @ref FLASH_IT_ERR Error Interrupt    
+  * @retval none
+  */  
+#define __HAL_FLASH_DISABLE_IT(__INTERRUPT__)  CLEAR_BIT((FLASH->CR), (uint32_t)(__INTERRUPT__))
+
+/**
+  * @brief  Get the specified FLASH flag status. 
+  * @param  __FLAG__ specifies the FLASH flag to check.
+  *          This parameter can be one of the following values:
+  *            @arg @ref FLASH_FLAG_BSY         FLASH Busy flag
+  *            @arg @ref FLASH_FLAG_EOP         FLASH End of Operation flag 
+  *            @arg @ref FLASH_FLAG_WRPERR      FLASH Write protected error flag 
+  *            @arg @ref FLASH_FLAG_PGERR       FLASH Programming error flag
+  * @retval The new state of __FLAG__ (SET or RESET).
+  */
+#define __HAL_FLASH_GET_FLAG(__FLAG__)   (((FLASH->SR) & (__FLAG__)) == (__FLAG__))
+
+/**
+  * @brief  Clear the specified FLASH flag.
+  * @param  __FLAG__ specifies the FLASH flags to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg @ref FLASH_FLAG_EOP         FLASH End of Operation flag 
+  *            @arg @ref FLASH_FLAG_WRPERR      FLASH Write protected error flag 
+  *            @arg @ref FLASH_FLAG_PGERR       FLASH Programming error flag
+  * @retval none
+  */
+#define __HAL_FLASH_CLEAR_FLAG(__FLAG__)   ((FLASH->SR) = (__FLAG__))
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+/* Include FLASH HAL Extended module */
+#include "stm32f0xx_hal_flash_ex.h"  
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup FLASH_Exported_Functions
+  * @{
+  */
+  
+/** @addtogroup FLASH_Exported_Functions_Group1
+  * @{
+  */
+/* IO operation functions *****************************************************/
+HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint64_t Data);
+HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint64_t Data);
+
+/* FLASH IRQ handler function */
+void       HAL_FLASH_IRQHandler(void);
+/* Callbacks in non blocking modes */ 
+void       HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue);
+void       HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue);
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Exported_Functions_Group2
+  * @{
+  */
+/* Peripheral Control functions ***********************************************/
+HAL_StatusTypeDef HAL_FLASH_Unlock(void);
+HAL_StatusTypeDef HAL_FLASH_Lock(void);
+HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void);
+HAL_StatusTypeDef HAL_FLASH_OB_Lock(void);
+HAL_StatusTypeDef HAL_FLASH_OB_Launch(void);
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral State and Error functions ***************************************/
+uint32_t HAL_FLASH_GetError(void);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private function -------------------------------------------------*/
+/** @addtogroup FLASH_Private_Functions
+ * @{
+ */
+HAL_StatusTypeDef       FLASH_WaitForLastOperation(uint32_t Timeout);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_FLASH_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_flash_ex.h

@@ -0,0 +1,448 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_flash_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of Flash HAL Extended module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_FLASH_EX_H
+#define __STM32F0xx_HAL_FLASH_EX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup FLASHEx
+  * @{
+  */ 
+
+/** @addtogroup FLASHEx_Private_Macros
+  * @{
+  */
+#define IS_FLASH_TYPEERASE(VALUE) (((VALUE) == FLASH_TYPEERASE_PAGES) || \
+                             ((VALUE) == FLASH_TYPEERASE_MASSERASE))  
+
+#define IS_OPTIONBYTE(VALUE) ((VALUE) <= (OPTIONBYTE_WRP | OPTIONBYTE_RDP | OPTIONBYTE_USER | OPTIONBYTE_DATA))
+
+#define IS_WRPSTATE(VALUE) (((VALUE) == OB_WRPSTATE_DISABLE) || \
+                            ((VALUE) == OB_WRPSTATE_ENABLE))  
+
+#define IS_OB_DATA_ADDRESS(ADDRESS) (((ADDRESS) == OB_DATA_ADDRESS_DATA0) || ((ADDRESS) == OB_DATA_ADDRESS_DATA1)) 
+
+#define IS_OB_RDP_LEVEL(LEVEL)     (((LEVEL) == OB_RDP_LEVEL_0)   ||\
+                                    ((LEVEL) == OB_RDP_LEVEL_1))/*||\
+                                    ((LEVEL) == OB_RDP_LEVEL_2))*/
+
+#define IS_OB_IWDG_SOURCE(SOURCE)  (((SOURCE) == OB_IWDG_SW) || ((SOURCE) == OB_IWDG_HW))
+
+#define IS_OB_STOP_SOURCE(SOURCE)  (((SOURCE) == OB_STOP_NO_RST) || ((SOURCE) == OB_STOP_RST))
+
+#define IS_OB_STDBY_SOURCE(SOURCE) (((SOURCE) == OB_STDBY_NO_RST) || ((SOURCE) == OB_STDBY_RST))
+
+#define IS_OB_BOOT1(BOOT1)         (((BOOT1) == OB_BOOT1_RESET) || ((BOOT1) == OB_BOOT1_SET))
+
+#define IS_OB_VDDA_ANALOG(ANALOG)  (((ANALOG) == OB_VDDA_ANALOG_ON) || ((ANALOG) == OB_VDDA_ANALOG_OFF))
+
+#define IS_OB_SRAM_PARITY(PARITY)  (((PARITY) == OB_SRAM_PARITY_SET) || ((PARITY) == OB_SRAM_PARITY_RESET))
+
+#if defined(FLASH_OBR_BOOT_SEL)
+#define IS_OB_BOOT_SEL(BOOT_SEL)   (((BOOT_SEL) == OB_BOOT_SEL_RESET) || ((BOOT_SEL) == OB_BOOT_SEL_SET))
+#define IS_OB_BOOT0(BOOT0)         (((BOOT0) == OB_BOOT0_RESET) || ((BOOT0) == OB_BOOT0_SET))
+#endif /* FLASH_OBR_BOOT_SEL */
+
+
+#define IS_OB_WRP(PAGE) (((PAGE) != 0x0000000U))
+
+#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= FLASH_BANK1_END)
+
+#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) (((ADDRESS) >= FLASH_BASE) && ((ADDRESS) <= FLASH_BANK1_END))
+
+/**
+  * @}
+  */
+
+/* Exported types ------------------------------------------------------------*/ 
+/** @defgroup FLASHEx_Exported_Types FLASHEx Exported Types
+  * @{
+  */
+/**
+  * @brief  FLASH Erase structure definition
+  */
+typedef struct
+{
+  uint32_t TypeErase;   /*!< TypeErase: Mass erase or page erase.
+                             This parameter can be a value of @ref FLASHEx_Type_Erase */
+
+  uint32_t PageAddress; /*!< PageAdress: Initial FLASH page address to erase when mass erase is disabled
+                             This parameter must be a number between Min_Data = FLASH_BASE and Max_Data = FLASH_BANK1_END */
+  
+  uint32_t NbPages;     /*!< NbPages: Number of pagess to be erased.
+                             This parameter must be a value between Min_Data = 1 and Max_Data = (max number of pages - value of initial page)*/
+                                                          
+} FLASH_EraseInitTypeDef;
+
+/**
+  * @brief  FLASH Options bytes program structure definition
+  */
+typedef struct
+{
+  uint32_t OptionType;  /*!< OptionType: Option byte to be configured.
+                             This parameter can be a value of @ref FLASHEx_OB_Type */
+
+  uint32_t WRPState;    /*!< WRPState: Write protection activation or deactivation.
+                             This parameter can be a value of @ref FLASHEx_OB_WRP_State */
+
+  uint32_t WRPPage;     /*!< WRPPage: specifies the page(s) to be write protected
+                             This parameter can be a value of @ref FLASHEx_OB_Write_Protection */
+
+  uint8_t RDPLevel;     /*!< RDPLevel: Set the read protection level..
+                             This parameter can be a value of @ref FLASHEx_OB_Read_Protection */
+
+  uint8_t USERConfig;   /*!< USERConfig: Program the FLASH User Option Byte: 
+                             IWDG / STOP / STDBY / BOOT1 / VDDA_ANALOG / SRAM_PARITY
+                             This parameter can be a combination of @ref FLASHEx_OB_IWatchdog, @ref FLASHEx_OB_nRST_STOP,
+                             @ref FLASHEx_OB_nRST_STDBY, @ref FLASHEx_OB_BOOT1, @ref FLASHEx_OB_VDDA_Analog_Monitoring and
+                             @ref FLASHEx_OB_RAM_Parity_Check_Enable */
+
+  uint32_t DATAAddress; /*!< DATAAddress: Address of the option byte DATA to be programmed
+                             This parameter can be a value of @ref FLASHEx_OB_Data_Address */
+  
+  uint8_t DATAData;     /*!< DATAData: Data to be stored in the option byte DATA
+                             This parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFF */  
+} FLASH_OBProgramInitTypeDef;
+/**
+  * @}
+  */  
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup FLASHEx_Exported_Constants FLASHEx Exported Constants
+  * @{
+  */
+
+/** @defgroup FLASHEx_Page_Size FLASHEx Page Size
+  * @{
+  */
+#if defined(STM32F030x6) || defined(STM32F030x8) || defined(STM32F031x6) || defined(STM32F038xx) \
+ || defined(STM32F051x8) || defined(STM32F042x6) || defined(STM32F048xx) || defined(STM32F058xx) || defined(STM32F070x6)
+#define FLASH_PAGE_SIZE          0x400U
+#endif /* STM32F030x6 || STM32F030x8 || STM32F031x6 || STM32F051x8 || STM32F042x6 || STM32F048xx || STM32F058xx || STM32F070x6 */
+
+#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F070xB) \
+ || defined(STM32F091xC) || defined(STM32F098xx) || defined(STM32F030xC)
+#define FLASH_PAGE_SIZE          0x800U
+#endif /* STM32F071xB || STM32F072xB || STM32F078xx || STM32F091xC || STM32F098xx || STM32F030xC */
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Type_Erase FLASH Type Erase
+  * @{
+  */ 
+#define FLASH_TYPEERASE_PAGES     (0x00U)  /*!<Pages erase only*/
+#define FLASH_TYPEERASE_MASSERASE (0x01U)  /*!<Flash mass erase activation*/
+
+/**
+  * @}
+  */
+  
+/** @defgroup FLASHEx_OptionByte_Constants Option Byte Constants
+  * @{
+  */ 
+
+/** @defgroup FLASHEx_OB_Type Option Bytes Type
+  * @{
+  */
+#define OPTIONBYTE_WRP       (0x01U)  /*!<WRP option byte configuration*/
+#define OPTIONBYTE_RDP       (0x02U)  /*!<RDP option byte configuration*/
+#define OPTIONBYTE_USER      (0x04U)  /*!<USER option byte configuration*/
+#define OPTIONBYTE_DATA      (0x08U)  /*!<DATA option byte configuration*/
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_WRP_State Option Byte WRP State
+  * @{
+  */ 
+#define OB_WRPSTATE_DISABLE   (0x00U)  /*!<Disable the write protection of the desired pages*/
+#define OB_WRPSTATE_ENABLE    (0x01U)  /*!<Enable the write protection of the desired pagess*/
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_Write_Protection FLASHEx OB Write Protection
+  * @{
+  */
+#if defined(STM32F030x6) || defined(STM32F030x8) || defined(STM32F031x6) || defined(STM32F038xx) \
+ || defined(STM32F051x8) || defined(STM32F042x6) || defined(STM32F048xx) || defined(STM32F058xx) || defined(STM32F070x6) 
+#define OB_WRP_PAGES0TO3               (0x00000001U) /* Write protection of page 0 to 3 */
+#define OB_WRP_PAGES4TO7               (0x00000002U) /* Write protection of page 4 to 7 */
+#define OB_WRP_PAGES8TO11              (0x00000004U) /* Write protection of page 8 to 11 */
+#define OB_WRP_PAGES12TO15             (0x00000008U) /* Write protection of page 12 to 15 */
+#define OB_WRP_PAGES16TO19             (0x00000010U) /* Write protection of page 16 to 19 */
+#define OB_WRP_PAGES20TO23             (0x00000020U) /* Write protection of page 20 to 23 */
+#define OB_WRP_PAGES24TO27             (0x00000040U) /* Write protection of page 24 to 27 */
+#define OB_WRP_PAGES28TO31             (0x00000080U) /* Write protection of page 28 to 31 */
+#if defined(STM32F030x8) || defined(STM32F051x8) || defined(STM32F058xx)
+#define OB_WRP_PAGES32TO35             (0x00000100U) /* Write protection of page 32 to 35 */
+#define OB_WRP_PAGES36TO39             (0x00000200U) /* Write protection of page 36 to 39 */
+#define OB_WRP_PAGES40TO43             (0x00000400U) /* Write protection of page 40 to 43 */
+#define OB_WRP_PAGES44TO47             (0x00000800U) /* Write protection of page 44 to 47 */
+#define OB_WRP_PAGES48TO51             (0x00001000U) /* Write protection of page 48 to 51 */
+#define OB_WRP_PAGES52TO57             (0x00002000U) /* Write protection of page 52 to 57 */
+#define OB_WRP_PAGES56TO59             (0x00004000U) /* Write protection of page 56 to 59 */
+#define OB_WRP_PAGES60TO63             (0x00008000U) /* Write protection of page 60 to 63 */
+#endif /* STM32F030x8 || STM32F051x8 || STM32F058xx */
+
+#if defined(STM32F030x6) || defined(STM32F030x8) || defined(STM32F031x6) || defined(STM32F038xx) \
+ || defined(STM32F051x8) || defined(STM32F042x6) || defined(STM32F048xx) || defined(STM32F058xx) || defined(STM32F070x6) 
+#define OB_WRP_PAGES0TO31MASK          (0x000000FFU)
+#endif /* STM32F030x6 || STM32F030x8 || STM32F031x6 || STM32F051x8 || STM32F042x6 || STM32F048xx || STM32F038xx || STM32F058xx || STM32F070x6 */
+
+#if defined(STM32F030x8) || defined(STM32F051x8) || defined(STM32F058xx)
+#define OB_WRP_PAGES32TO63MASK         (0x0000FF00U)
+#endif /* STM32F030x8 || STM32F051x8 || STM32F058xx */
+
+#if defined(STM32F030x6) || defined(STM32F031x6) || defined(STM32F042x6) || defined(STM32F048xx) || defined(STM32F038xx)|| defined(STM32F070x6)
+#define OB_WRP_ALLPAGES                (0x000000FFU) /*!< Write protection of all pages */
+#endif /* STM32F030x6 || STM32F031x6 || STM32F042x6 || STM32F048xx || STM32F038xx || STM32F070x6 */
+
+#if defined(STM32F030x8) || defined(STM32F051x8) || defined(STM32F058xx)
+#define OB_WRP_ALLPAGES                (0x0000FFFFU) /*!< Write protection of all pages */
+#endif /* STM32F030x8 || STM32F051x8 || STM32F058xx */
+#endif /* STM32F030x6 || STM32F030x8 || STM32F031x6 || STM32F051x8 || STM32F042x6 || STM32F048xx || STM32F038xx || STM32F058xx || STM32F070x6 */
+      
+#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F070xB) \
+ || defined(STM32F091xC) || defined(STM32F098xx) || defined(STM32F030xC)
+#define OB_WRP_PAGES0TO1               (0x00000001U) /* Write protection of page 0 to 1 */
+#define OB_WRP_PAGES2TO3               (0x00000002U) /* Write protection of page 2 to 3 */
+#define OB_WRP_PAGES4TO5               (0x00000004U) /* Write protection of page 4 to 5 */
+#define OB_WRP_PAGES6TO7               (0x00000008U) /* Write protection of page 6 to 7 */
+#define OB_WRP_PAGES8TO9               (0x00000010U) /* Write protection of page 8 to 9 */
+#define OB_WRP_PAGES10TO11             (0x00000020U) /* Write protection of page 10 to 11 */
+#define OB_WRP_PAGES12TO13             (0x00000040U) /* Write protection of page 12 to 13 */
+#define OB_WRP_PAGES14TO15             (0x00000080U) /* Write protection of page 14 to 15 */
+#define OB_WRP_PAGES16TO17             (0x00000100U) /* Write protection of page 16 to 17 */
+#define OB_WRP_PAGES18TO19             (0x00000200U) /* Write protection of page 18 to 19 */
+#define OB_WRP_PAGES20TO21             (0x00000400U) /* Write protection of page 20 to 21 */
+#define OB_WRP_PAGES22TO23             (0x00000800U) /* Write protection of page 22 to 23 */
+#define OB_WRP_PAGES24TO25             (0x00001000U) /* Write protection of page 24 to 25 */
+#define OB_WRP_PAGES26TO27             (0x00002000U) /* Write protection of page 26 to 27 */
+#define OB_WRP_PAGES28TO29             (0x00004000U) /* Write protection of page 28 to 29 */
+#define OB_WRP_PAGES30TO31             (0x00008000U) /* Write protection of page 30 to 31 */
+#define OB_WRP_PAGES32TO33             (0x00010000U) /* Write protection of page 32 to 33 */
+#define OB_WRP_PAGES34TO35             (0x00020000U) /* Write protection of page 34 to 35 */
+#define OB_WRP_PAGES36TO37             (0x00040000U) /* Write protection of page 36 to 37 */
+#define OB_WRP_PAGES38TO39             (0x00080000U) /* Write protection of page 38 to 39 */
+#define OB_WRP_PAGES40TO41             (0x00100000U) /* Write protection of page 40 to 41 */
+#define OB_WRP_PAGES42TO43             (0x00200000U) /* Write protection of page 42 to 43 */
+#define OB_WRP_PAGES44TO45             (0x00400000U) /* Write protection of page 44 to 45 */
+#define OB_WRP_PAGES46TO47             (0x00800000U) /* Write protection of page 46 to 47 */
+#define OB_WRP_PAGES48TO49             (0x01000000U) /* Write protection of page 48 to 49 */
+#define OB_WRP_PAGES50TO51             (0x02000000U) /* Write protection of page 50 to 51 */
+#define OB_WRP_PAGES52TO53             (0x04000000U) /* Write protection of page 52 to 53 */
+#define OB_WRP_PAGES54TO55             (0x08000000U) /* Write protection of page 54 to 55 */
+#define OB_WRP_PAGES56TO57             (0x10000000U) /* Write protection of page 56 to 57 */
+#define OB_WRP_PAGES58TO59             (0x20000000U) /* Write protection of page 58 to 59 */
+#define OB_WRP_PAGES60TO61             (0x40000000U) /* Write protection of page 60 to 61 */
+#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F070xB)
+#define OB_WRP_PAGES62TO63             (0x80000000U) /* Write protection of page 62 to 63 */
+#endif /* STM32F071xB || STM32F072xB || STM32F078xx || STM32F070xB */
+#if defined(STM32F091xC) || defined(STM32F098xx) || defined(STM32F030xC)
+#define OB_WRP_PAGES62TO127            (0x80000000U) /* Write protection of page 62 to 127 */
+#endif /* STM32F091xC || STM32F098xx || STM32F030xC */
+
+#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F070xB) \
+ || defined(STM32F091xC) || defined(STM32F098xx)|| defined(STM32F030xC)
+#define OB_WRP_PAGES0TO15MASK          (0x000000FFU)
+#define OB_WRP_PAGES16TO31MASK         (0x0000FF00U)
+#define OB_WRP_PAGES32TO47MASK         (0x00FF0000U)
+#endif /* STM32F071xB || STM32F072xB || STM32F078xx  || STM32F091xC || STM32F098xx || STM32F070xB || STM32F030xC */
+
+#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F070xB)
+#define OB_WRP_PAGES48TO63MASK         (0xFF000000U)
+#endif /* STM32F071xB || STM32F072xB || STM32F078xx || STM32F070xB */
+#if defined(STM32F091xC) || defined(STM32F098xx) || defined(STM32F030xC)
+#define OB_WRP_PAGES48TO127MASK        (0xFF000000U)
+#endif /* STM32F091xC || STM32F098xx || STM32F030xC */
+
+#define OB_WRP_ALLPAGES                (0xFFFFFFFFU) /*!< Write protection of all pages */
+#endif /* STM32F071xB || STM32F072xB || STM32F078xx  || STM32F091xC || STM32F098xx || STM32F030xC || STM32F070xB */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_Read_Protection Option Byte Read Protection
+  * @{
+  */
+#define OB_RDP_LEVEL_0             ((uint8_t)0xAAU)
+#define OB_RDP_LEVEL_1             ((uint8_t)0xBBU)
+#define OB_RDP_LEVEL_2             ((uint8_t)0xCCU) /*!< Warning: When enabling read protection level 2 
+                                                      it's no more possible to go back to level 1 or 0 */
+/**
+  * @}
+  */
+  
+/** @defgroup FLASHEx_OB_IWatchdog Option Byte IWatchdog
+  * @{
+  */ 
+#define OB_IWDG_SW                 ((uint8_t)0x01U)  /*!< Software IWDG selected */
+#define OB_IWDG_HW                 ((uint8_t)0x00U)  /*!< Hardware IWDG selected */
+/**
+  * @}
+  */
+  
+/** @defgroup FLASHEx_OB_nRST_STOP Option Byte nRST STOP
+  * @{
+  */ 
+#define OB_STOP_NO_RST             ((uint8_t)0x02U) /*!< No reset generated when entering in STOP */
+#define OB_STOP_RST                ((uint8_t)0x00U) /*!< Reset generated when entering in STOP */
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_nRST_STDBY Option Byte nRST STDBY
+  * @{
+  */ 
+#define OB_STDBY_NO_RST            ((uint8_t)0x04U) /*!< No reset generated when entering in STANDBY */
+#define OB_STDBY_RST               ((uint8_t)0x00U) /*!< Reset generated when entering in STANDBY */
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_BOOT1 Option Byte BOOT1
+  * @{
+  */
+#define OB_BOOT1_RESET             ((uint8_t)0x00U) /*!< BOOT1 Reset */
+#define OB_BOOT1_SET               ((uint8_t)0x10U) /*!< BOOT1 Set */
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_VDDA_Analog_Monitoring Option Byte VDDA Analog Monitoring
+  * @{
+  */
+#define OB_VDDA_ANALOG_ON          ((uint8_t)0x20U) /*!< Analog monitoring on VDDA Power source ON */
+#define OB_VDDA_ANALOG_OFF         ((uint8_t)0x00U) /*!< Analog monitoring on VDDA Power source OFF */
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_RAM_Parity_Check_Enable Option Byte SRAM Parity Check Enable
+  * @{
+  */
+#define OB_SRAM_PARITY_SET         ((uint8_t)0x00U) /*!< SRAM parity check enable set */
+#define OB_SRAM_PARITY_RESET       ((uint8_t)0x40U) /*!< SRAM parity check enable reset */
+/**
+  * @}
+  */
+
+#if defined(FLASH_OBR_BOOT_SEL)
+/** @defgroup FLASHEx_OB_BOOT_SEL FLASHEx Option Byte BOOT SEL
+  * @{
+  */
+#define OB_BOOT_SEL_RESET          ((uint8_t)0x00U) /*!< BOOT_SEL Reset */
+#define OB_BOOT_SEL_SET            ((uint8_t)0x80U) /*!< BOOT_SEL Set */
+/**
+  * @}
+  */  
+
+/** @defgroup FLASHEx_OB_BOOT0 FLASHEx Option Byte BOOT0
+  * @{
+  */
+#define OB_BOOT0_RESET             ((uint8_t)0x00U) /*!< BOOT0 Reset */
+#define OB_BOOT0_SET               ((uint8_t)0x08U) /*!< BOOT0 Set */
+/**
+  * @}
+  */
+#endif /* FLASH_OBR_BOOT_SEL */
+
+
+/** @defgroup FLASHEx_OB_Data_Address  Option Byte Data Address
+  * @{
+  */
+#define OB_DATA_ADDRESS_DATA0     (0x1FFFF804U)
+#define OB_DATA_ADDRESS_DATA1     (0x1FFFF806U)
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup FLASHEx_Exported_Functions
+  * @{
+  */
+  
+/** @addtogroup FLASHEx_Exported_Functions_Group1
+  * @{
+  */   
+/* IO operation functions *****************************************************/
+HAL_StatusTypeDef  HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef *pEraseInit, uint32_t *PageError);
+HAL_StatusTypeDef  HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef *pEraseInit);
+
+/**
+  * @}
+  */ 
+
+/** @addtogroup FLASHEx_Exported_Functions_Group2
+  * @{
+  */   
+/* Peripheral Control functions ***********************************************/
+HAL_StatusTypeDef  HAL_FLASHEx_OBErase(void);
+HAL_StatusTypeDef  HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit);
+void               HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef *pOBInit);
+uint32_t           HAL_FLASHEx_OBGetUserData(uint32_t DATAAdress);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_FLASH_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_gpio.h

@@ -0,0 +1,296 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_gpio.h
+  * @author  MCD Application Team
+  * @brief   Header file of GPIO HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_GPIO_H
+#define __STM32F0xx_HAL_GPIO_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup GPIO
+  * @{
+  */ 
+
+/* Exported types ------------------------------------------------------------*/ 
+
+/** @defgroup GPIO_Exported_Types GPIO Exported Types
+  * @{
+  */
+/** 
+  * @brief   GPIO Init structure definition  
+  */
+typedef struct
+{
+  uint32_t Pin;       /*!< Specifies the GPIO pins to be configured.
+                           This parameter can be any value of @ref GPIO_pins */
+
+  uint32_t Mode;      /*!< Specifies the operating mode for the selected pins.
+                           This parameter can be a value of @ref GPIO_mode */
+
+  uint32_t Pull;      /*!< Specifies the Pull-up or Pull-Down activation for the selected pins.
+                           This parameter can be a value of @ref GPIO_pull */
+
+  uint32_t Speed;     /*!< Specifies the speed for the selected pins.
+                           This parameter can be a value of @ref GPIO_speed */
+
+  uint32_t Alternate;  /*!< Peripheral to be connected to the selected pins 
+                            This parameter can be a value of @ref GPIOEx_Alternate_function_selection */
+}GPIO_InitTypeDef;
+
+/** 
+  * @brief  GPIO Bit SET and Bit RESET enumeration 
+  */
+typedef enum
+{
+  GPIO_PIN_RESET = 0U,
+  GPIO_PIN_SET
+}GPIO_PinState;
+/**
+  * @}
+  */
+  
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup GPIO_Exported_Constants GPIO Exported Constants
+  * @{
+  */
+/** @defgroup GPIO_pins GPIO pins
+  * @{
+  */
+#define GPIO_PIN_0                 ((uint16_t)0x0001U)  /* Pin 0 selected    */
+#define GPIO_PIN_1                 ((uint16_t)0x0002U)  /* Pin 1 selected    */
+#define GPIO_PIN_2                 ((uint16_t)0x0004U)  /* Pin 2 selected    */
+#define GPIO_PIN_3                 ((uint16_t)0x0008U)  /* Pin 3 selected    */
+#define GPIO_PIN_4                 ((uint16_t)0x0010U)  /* Pin 4 selected    */
+#define GPIO_PIN_5                 ((uint16_t)0x0020U)  /* Pin 5 selected    */
+#define GPIO_PIN_6                 ((uint16_t)0x0040U)  /* Pin 6 selected    */
+#define GPIO_PIN_7                 ((uint16_t)0x0080U)  /* Pin 7 selected    */
+#define GPIO_PIN_8                 ((uint16_t)0x0100U)  /* Pin 8 selected    */
+#define GPIO_PIN_9                 ((uint16_t)0x0200U)  /* Pin 9 selected    */
+#define GPIO_PIN_10                ((uint16_t)0x0400U)  /* Pin 10 selected   */
+#define GPIO_PIN_11                ((uint16_t)0x0800U)  /* Pin 11 selected   */
+#define GPIO_PIN_12                ((uint16_t)0x1000U)  /* Pin 12 selected   */
+#define GPIO_PIN_13                ((uint16_t)0x2000U)  /* Pin 13 selected   */
+#define GPIO_PIN_14                ((uint16_t)0x4000U)  /* Pin 14 selected   */
+#define GPIO_PIN_15                ((uint16_t)0x8000U)  /* Pin 15 selected   */
+#define GPIO_PIN_All               ((uint16_t)0xFFFFU)  /* All pins selected */
+
+#define GPIO_PIN_MASK              (0x0000FFFFU) /* PIN mask for assert test */
+/**
+  * @}
+  */
+
+/** @defgroup GPIO_mode GPIO mode
+  * @brief GPIO Configuration Mode 
+  *        Elements values convention: 0xX0yz00YZ
+  *           - X  : GPIO mode or EXTI Mode
+  *           - y  : External IT or Event trigger detection 
+  *           - z  : IO configuration on External IT or Event
+  *           - Y  : Output type (Push Pull or Open Drain)
+  *           - Z  : IO Direction mode (Input, Output, Alternate or Analog)
+  * @{
+  */ 
+#define  GPIO_MODE_INPUT                        (0x00000000U)   /*!< Input Floating Mode                   */
+#define  GPIO_MODE_OUTPUT_PP                    (0x00000001U)   /*!< Output Push Pull Mode                 */
+#define  GPIO_MODE_OUTPUT_OD                    (0x00000011U)   /*!< Output Open Drain Mode                */
+#define  GPIO_MODE_AF_PP                        (0x00000002U)   /*!< Alternate Function Push Pull Mode     */
+#define  GPIO_MODE_AF_OD                        (0x00000012U)   /*!< Alternate Function Open Drain Mode    */
+#define  GPIO_MODE_ANALOG                       (0x00000003U)   /*!< Analog Mode  */  
+#define  GPIO_MODE_IT_RISING                    (0x10110000U)   /*!< External Interrupt Mode with Rising edge trigger detection          */
+#define  GPIO_MODE_IT_FALLING                   (0x10210000U)   /*!< External Interrupt Mode with Falling edge trigger detection         */
+#define  GPIO_MODE_IT_RISING_FALLING            (0x10310000U)   /*!< External Interrupt Mode with Rising/Falling edge trigger detection  */
+#define  GPIO_MODE_EVT_RISING                   (0x10120000U)   /*!< External Event Mode with Rising edge trigger detection               */
+#define  GPIO_MODE_EVT_FALLING                  (0x10220000U)   /*!< External Event Mode with Falling edge trigger detection              */
+#define  GPIO_MODE_EVT_RISING_FALLING           (0x10320000U)   /*!< External Event Mode with Rising/Falling edge trigger detection       */
+/**
+  * @}
+  */
+                                                         
+/** @defgroup GPIO_speed GPIO speed
+  * @brief GPIO Output Maximum frequency
+  * @{
+  */  
+#define  GPIO_SPEED_FREQ_LOW      (0x00000000U)  /*!< range up to 2 MHz, please refer to the product datasheet */
+#define  GPIO_SPEED_FREQ_MEDIUM   (0x00000001U)  /*!< range  4 MHz to 10 MHz, please refer to the product datasheet */
+#define  GPIO_SPEED_FREQ_HIGH     (0x00000003U)  /*!< range 10 MHz to 50 MHz, please refer to the product datasheet */
+/**
+  * @}
+  */
+
+ /** @defgroup GPIO_pull GPIO pull
+   * @brief GPIO Pull-Up or Pull-Down Activation
+   * @{
+   */  
+#define  GPIO_NOPULL        (0x00000000U)   /*!< No Pull-up or Pull-down activation  */
+#define  GPIO_PULLUP        (0x00000001U)   /*!< Pull-up activation                  */
+#define  GPIO_PULLDOWN      (0x00000002U)   /*!< Pull-down activation                */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup GPIO_Exported_Macros GPIO Exported Macros
+  * @{
+  */
+  
+/**
+  * @brief  Check whether the specified EXTI line flag is set or not.
+  * @param  __EXTI_LINE__ specifies the EXTI line flag to check.
+  *         This parameter can be GPIO_PIN_x where x can be(0..15)
+  * @retval The new state of __EXTI_LINE__ (SET or RESET).
+  */
+#define __HAL_GPIO_EXTI_GET_FLAG(__EXTI_LINE__) (EXTI->PR & (__EXTI_LINE__))
+
+/**
+  * @brief  Clear the EXTI's line pending flags.
+  * @param  __EXTI_LINE__ specifies the EXTI lines flags to clear.
+  *         This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
+  * @retval None
+  */
+#define __HAL_GPIO_EXTI_CLEAR_FLAG(__EXTI_LINE__) (EXTI->PR = (__EXTI_LINE__))
+
+/**
+  * @brief  Check whether the specified EXTI line is asserted or not.
+  * @param  __EXTI_LINE__ specifies the EXTI line to check.
+  *          This parameter can be GPIO_PIN_x where x can be(0..15)
+  * @retval The new state of __EXTI_LINE__ (SET or RESET).
+  */
+#define __HAL_GPIO_EXTI_GET_IT(__EXTI_LINE__) (EXTI->PR & (__EXTI_LINE__))
+
+/**
+  * @brief  Clear the EXTI's line pending bits.
+  * @param  __EXTI_LINE__ specifies the EXTI lines to clear.
+  *          This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
+  * @retval None
+  */
+#define __HAL_GPIO_EXTI_CLEAR_IT(__EXTI_LINE__) (EXTI->PR = (__EXTI_LINE__))
+
+/**
+  * @brief  Generate a Software interrupt on selected EXTI line.
+  * @param  __EXTI_LINE__ specifies the EXTI line to check.
+  *          This parameter can be GPIO_PIN_x where x can be(0..15)
+  * @retval None
+  */
+#define __HAL_GPIO_EXTI_GENERATE_SWIT(__EXTI_LINE__) (EXTI->SWIER |= (__EXTI_LINE__))
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @addtogroup GPIO_Private_Macros GPIO Private Macros
+  * @{
+  */
+#define IS_GPIO_PIN_ACTION(ACTION)  (((ACTION) == GPIO_PIN_RESET) || ((ACTION) == GPIO_PIN_SET))
+
+#define IS_GPIO_PIN(__PIN__)        (((((uint32_t)__PIN__) & GPIO_PIN_MASK) != 0x00U) &&\
+                                     ((((uint32_t)__PIN__) & ~GPIO_PIN_MASK) == 0x00U))
+
+#define IS_GPIO_MODE(__MODE__)      (((__MODE__) == GPIO_MODE_INPUT)              ||\
+                                     ((__MODE__) == GPIO_MODE_OUTPUT_PP)          ||\
+                                     ((__MODE__) == GPIO_MODE_OUTPUT_OD)          ||\
+                                     ((__MODE__) == GPIO_MODE_AF_PP)              ||\
+                                     ((__MODE__) == GPIO_MODE_AF_OD)              ||\
+                                     ((__MODE__) == GPIO_MODE_IT_RISING)          ||\
+                                     ((__MODE__) == GPIO_MODE_IT_FALLING)         ||\
+                                     ((__MODE__) == GPIO_MODE_IT_RISING_FALLING)  ||\
+                                     ((__MODE__) == GPIO_MODE_EVT_RISING)         ||\
+                                     ((__MODE__) == GPIO_MODE_EVT_FALLING)        ||\
+                                     ((__MODE__) == GPIO_MODE_EVT_RISING_FALLING) ||\
+                                     ((__MODE__) == GPIO_MODE_ANALOG))
+
+#define IS_GPIO_SPEED(__SPEED__)    (((__SPEED__) == GPIO_SPEED_FREQ_LOW)    ||\
+                                     ((__SPEED__) == GPIO_SPEED_FREQ_MEDIUM) ||\
+                                     ((__SPEED__) == GPIO_SPEED_FREQ_HIGH))
+
+#define IS_GPIO_PULL(__PULL__)      (((__PULL__) == GPIO_NOPULL)   ||\
+                                     ((__PULL__) == GPIO_PULLUP)   || \
+                                     ((__PULL__) == GPIO_PULLDOWN))
+/**
+  * @}
+  */
+
+/* Include GPIO HAL Extended module */
+#include "stm32f0xx_hal_gpio_ex.h"
+
+/* Exported functions --------------------------------------------------------*/ 
+/** @addtogroup GPIO_Exported_Functions GPIO Exported Functions
+  * @{
+  */
+
+/** @addtogroup GPIO_Exported_Functions_Group1 Initialization/de-initialization functions 
+ *  @brief    Initialization and Configuration functions
+ * @{
+ */
+     
+/* Initialization and de-initialization functions *****************************/
+void              HAL_GPIO_Init(GPIO_TypeDef  *GPIOx, GPIO_InitTypeDef *GPIO_Init);
+void              HAL_GPIO_DeInit(GPIO_TypeDef  *GPIOx, uint32_t GPIO_Pin);
+
+/**
+  * @}
+  */
+
+/** @addtogroup GPIO_Exported_Functions_Group2 IO operation functions 
+ * @{
+ */
+   
+/* IO operation functions *****************************************************/
+GPIO_PinState     HAL_GPIO_ReadPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin);
+void              HAL_GPIO_WritePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState);
+void              HAL_GPIO_TogglePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin);
+HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin);
+void              HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin);
+void              HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin);
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */  
+  
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_GPIO_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_gpio_ex.h

@@ -0,0 +1,800 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_gpio_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of GPIO HAL Extension module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_GPIO_EX_H
+#define __STM32F0xx_HAL_GPIO_EX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup GPIOEx GPIOEx
+  * @{
+  */ 
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup GPIOEx_Exported_Constants GPIOEx Exported Constants
+  * @{
+  */ 
+  
+/** @defgroup GPIOEx_Alternate_function_selection GPIOEx Alternate function selection
+  * @{
+  */
+  
+#if defined (STM32F030x6)
+/*------------------------- STM32F030x6---------------------------*/ 
+/* AF 0 */
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1 Alternate Function mapping      */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_SWDIO        ((uint8_t)0x00U)  /*!< AF0: SWDIO Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+#define GPIO_AF0_TIM3         ((uint8_t)0x00U)  /*!< AF0: TIM3 Alternate Function mapping      */
+
+/* AF 1 */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+
+/* AF 2 */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+#define GPIO_AF4_I2C1         ((uint8_t)0x04U)  /*!< AF4: I2C1 Alternate Function mapping      */
+
+/* AF 5 */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+
+/* AF 6 */
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x06U)
+
+#endif /* STM32F030x6 */
+
+/*---------------------------------- STM32F030x8 -------------------------------------------*/
+#if defined (STM32F030x8)
+/* AF 0 */
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1 Alternate Function mapping      */
+#define GPIO_AF0_SPI2         ((uint8_t)0x00U)  /*!< AF0: SPI2 Alternate Function mapping      */
+#define GPIO_AF0_TIM15        ((uint8_t)0x00U)  /*!< AF0: TIM15 Alternate Function mapping     */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_SWDIO        ((uint8_t)0x00U)  /*!< AF0: SWDIO Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+#define GPIO_AF0_TIM3         ((uint8_t)0x00U)  /*!< AF0: TIM3 Alternate Function mapping      */
+
+/* AF 1 */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+#define GPIO_AF1_TIM15        ((uint8_t)0x01U)  /*!< AF1: TIM15 Alternate Function mapping     */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_USART2       ((uint8_t)0x01U)  /*!< AF1: USART2 Alternate Function mapping    */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_I2C2         ((uint8_t)0x01U)  /*!< AF1: I2C2 Alternate Function mapping      */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+
+/* AF 2 */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+#define GPIO_AF3_TIM15        ((uint8_t)0x03U)  /*!< AF3: TIM15 Alternate Function mapping     */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+
+/* AF 5 */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+
+/* AF 6 */
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x06U)
+
+#endif /* STM32F030x8 */
+
+#if defined (STM32F031x6) || defined (STM32F038xx)
+/*--------------------------- STM32F031x6/STM32F038xx ---------------------------*/
+/* AF 0 */
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1/I2S1 Alternate Function mapping */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_SWDAT        ((uint8_t)0x00U)  /*!< AF0: SWDAT Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+
+/* AF 1 */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+
+/* AF 2 */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM2         ((uint8_t)0x02U)  /*!< AF2: TIM2 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+#define GPIO_AF4_I2C1         ((uint8_t)0x04U)  /*!< AF4: I2C1 Alternate Function mapping      */
+
+/* AF 5 */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+
+/* AF 6 */
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x06U)
+
+#endif /* STM32F031x6 || STM32F038xx */
+
+#if defined (STM32F051x8) || defined (STM32F058xx)
+/*--------------------------- STM32F051x8/STM32F058xx---------------------------*/
+/* AF 0 */
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1/I2S1 Alternate Function mapping */
+#define GPIO_AF0_SPI2         ((uint8_t)0x00U)  /*!< AF0: SPI2 Alternate Function mapping      */
+#define GPIO_AF0_TIM15        ((uint8_t)0x00U)  /*!< AF0: TIM15 Alternate Function mapping     */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_SWDIO        ((uint8_t)0x00U)  /*!< AF0: SWDIO Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+#define GPIO_AF0_CEC          ((uint8_t)0x00U)  /*!< AF0: CEC Alternate Function mapping       */
+
+/* AF 1 */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+#define GPIO_AF1_TIM15        ((uint8_t)0x01U)  /*!< AF1: TIM15 Alternate Function mapping     */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_USART2       ((uint8_t)0x01U)  /*!< AF1: USART2 Alternate Function mapping    */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_I2C2         ((uint8_t)0x01U)  /*!< AF1: I2C2 Alternate Function mapping      */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+#define GPIO_AF1_CEC          ((uint8_t)0x01U)  /*!< AF1: CEC Alternate Function mapping       */
+
+/* AF 2 */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM2         ((uint8_t)0x02U)  /*!< AF2: TIM2 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+#define GPIO_AF3_TIM15        ((uint8_t)0x03U)  /*!< AF3: TIM15 Alternate Function mapping     */
+#define GPIO_AF3_TSC          ((uint8_t)0x03U)  /*!< AF3: TSC Alternate Function mapping       */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+
+/* AF 5 */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+
+/* AF 6 */
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+/* AF 7 */
+#define GPIO_AF7_COMP1        ((uint8_t)0x07U)  /*!< AF7: COMP1 Alternate Function mapping     */
+#define GPIO_AF7_COMP2        ((uint8_t)0x07U)  /*!< AF7: COMP2 Alternate Function mapping     */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x07U)
+
+#endif /* STM32F051x8/STM32F058xx */
+
+#if defined (STM32F071xB)
+/*--------------------------- STM32F071xB ---------------------------*/
+/* AF 0 */ 
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: AEVENTOUT Alternate Function mapping */
+#define GPIO_AF0_SWDIO        ((uint8_t)0x00U)  /*!< AF0: SWDIO Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_CEC          ((uint8_t)0x00U)  /*!< AF0: CEC Alternate Function mapping       */
+#define GPIO_AF0_CRS          ((uint8_t)0x00U)  /*!< AF0: CRS Alternate Function mapping       */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1/I2S1 Alternate Function mapping */
+#define GPIO_AF0_SPI2         ((uint8_t)0x00U)  /*!< AF0: SPI2/I2S2 Alternate Function mapping */
+#define GPIO_AF0_TIM1         ((uint8_t)0x00U)  /*!< AF0: TIM1 Alternate Function mapping      */
+#define GPIO_AF0_TIM3         ((uint8_t)0x00U)  /*!< AF0: TIM3 Alternate Function mapping      */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_TIM15        ((uint8_t)0x00U)  /*!< AF0: TIM15 Alternate Function mapping     */
+#define GPIO_AF0_TIM16        ((uint8_t)0x00U)  /*!< AF0: TIM16 Alternate Function mapping     */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_TSC          ((uint8_t)0x00U)  /*!< AF0: TSC Alternate Function mapping       */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+#define GPIO_AF0_USART2       ((uint8_t)0x00U)  /*!< AF0: USART2 Alternate Function mapping    */
+#define GPIO_AF0_USART3       ((uint8_t)0x00U)  /*!< AF0: USART3 Alternate Function mapping    */
+#define GPIO_AF0_USART4       ((uint8_t)0x00U)  /*!< AF0: USART4 Alternate Function mapping    */
+
+/* AF 1 */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+#define GPIO_AF1_TIM15        ((uint8_t)0x01U)  /*!< AF1: TIM15 Alternate Function mapping     */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_USART2       ((uint8_t)0x01U)  /*!< AF1: USART2 Alternate Function mapping    */
+#define GPIO_AF1_USART3       ((uint8_t)0x01U)  /*!< AF1: USART3 Alternate Function mapping    */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+#define GPIO_AF1_CEC          ((uint8_t)0x01U)  /*!< AF1: CEC Alternate Function mapping       */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_I2C2         ((uint8_t)0x01U)  /*!< AF1: I2C2 Alternate Function mapping      */
+#define GPIO_AF1_TSC          ((uint8_t)0x01U)  /*!< AF1: TSC Alternate Function mapping       */
+#define GPIO_AF1_SPI1         ((uint8_t)0x01U)  /*!< AF1: SPI1 Alternate Function mapping      */
+#define GPIO_AF1_SPI2         ((uint8_t)0x01U)  /*!< AF1: SPI2 Alternate Function mapping      */
+
+/* AF 2 */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM2         ((uint8_t)0x02U)  /*!< AF2: TIM2 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_TSC          ((uint8_t)0x03U)  /*!< AF3: TSC Alternate Function mapping       */
+#define GPIO_AF3_TIM15        ((uint8_t)0x03U)  /*!< AF3: TIM15 Alternate Function mapping     */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+#define GPIO_AF4_USART4       ((uint8_t)0x04U)  /*!< AF4: USART4 Alternate Function mapping    */
+#define GPIO_AF4_USART3       ((uint8_t)0x04U)  /*!< AF4: USART3 Alternate Function mapping    */
+#define GPIO_AF4_CRS          ((uint8_t)0x04U)  /*!< AF4: CRS Alternate Function mapping       */
+
+/* AF 5 */
+#define GPIO_AF5_TIM15        ((uint8_t)0x05U)  /*!< AF5: TIM15 Alternate Function mapping     */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+#define GPIO_AF5_SPI2         ((uint8_t)0x05U)  /*!< AF5: SPI2 Alternate Function mapping      */
+#define GPIO_AF5_I2C2         ((uint8_t)0x05U)  /*!< AF5: I2C2 Alternate Function mapping      */
+
+/* AF 6 */
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+/* AF 7 */
+#define GPIO_AF7_COMP1        ((uint8_t)0x07U)  /*!< AF7: COMP1 Alternate Function mapping     */
+#define GPIO_AF7_COMP2        ((uint8_t)0x07U)  /*!< AF7: COMP2 Alternate Function mapping     */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x07U)
+
+#endif /* STM32F071xB */
+
+
+#if defined(STM32F091xC) || defined(STM32F098xx)
+/*--------------------------- STM32F091xC || STM32F098xx ------------------------------*/
+/* AF 0 */
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF0_SWDIO        ((uint8_t)0x00U)  /*!< AF0: SWDIO Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_CEC          ((uint8_t)0x00U)  /*!< AF0: CEC Alternate Function mapping       */
+#define GPIO_AF0_CRS          ((uint8_t)0x00U)  /*!< AF0: CRS Alternate Function mapping       */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1/I2S1 Alternate Function mapping */
+#define GPIO_AF0_SPI2         ((uint8_t)0x00U)  /*!< AF0: SPI2/I2S2 Alternate Function mapping */
+#define GPIO_AF0_TIM1         ((uint8_t)0x00U)  /*!< AF0: TIM1 Alternate Function mapping      */
+#define GPIO_AF0_TIM3         ((uint8_t)0x00U)  /*!< AF0: TIM3 Alternate Function mapping      */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_TIM15        ((uint8_t)0x00U)  /*!< AF0: TIM15 Alternate Function mapping     */
+#define GPIO_AF0_TIM16        ((uint8_t)0x00U)  /*!< AF0: TIM16 Alternate Function mapping     */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_TSC          ((uint8_t)0x00U)  /*!< AF0: TSC Alternate Function mapping       */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+#define GPIO_AF0_USART2       ((uint8_t)0x00U)  /*!< AF0: USART2 Alternate Function mapping    */
+#define GPIO_AF0_USART3       ((uint8_t)0x00U)  /*!< AF0: USART3 Alternate Function mapping    */
+#define GPIO_AF0_USART4       ((uint8_t)0x00U)  /*!< AF0: USART4 Alternate Function mapping    */
+#define GPIO_AF0_USART8       ((uint8_t)0x00U)  /*!< AF0: USART8 Alternate Function mapping    */
+#define GPIO_AF0_CAN          ((uint8_t)0x00U)  /*!< AF0: CAN Alternate Function mapping       */
+
+/* AF 1 */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+#define GPIO_AF1_TIM15        ((uint8_t)0x01U)  /*!< AF1: TIM15 Alternate Function mapping     */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_USART2       ((uint8_t)0x01U)  /*!< AF1: USART2 Alternate Function mapping    */
+#define GPIO_AF1_USART3       ((uint8_t)0x01U)  /*!< AF1: USART3 Alternate Function mapping    */
+#define GPIO_AF1_USART4       ((uint8_t)0x01U)  /*!< AF1: USART4 Alternate Function mapping    */
+#define GPIO_AF1_USART5       ((uint8_t)0x01U)  /*!< AF1: USART5 Alternate Function mapping    */
+#define GPIO_AF1_USART6       ((uint8_t)0x01U)  /*!< AF1: USART6 Alternate Function mapping    */
+#define GPIO_AF1_USART7       ((uint8_t)0x01U)  /*!< AF1: USART7 Alternate Function mapping    */
+#define GPIO_AF1_USART8       ((uint8_t)0x01U)  /*!< AF1: USART8 Alternate Function mapping    */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+#define GPIO_AF1_CEC          ((uint8_t)0x01U)  /*!< AF1: CEC Alternate Function mapping       */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_I2C2         ((uint8_t)0x01U)  /*!< AF1: I2C2 Alternate Function mapping      */
+#define GPIO_AF1_TSC          ((uint8_t)0x01U)  /*!< AF1: TSC Alternate Function mapping       */
+#define GPIO_AF1_SPI1         ((uint8_t)0x01U)  /*!< AF1: SPI1 Alternate Function mapping      */
+#define GPIO_AF1_SPI2         ((uint8_t)0x01U)  /*!< AF1: SPI2 Alternate Function mapping      */
+
+/* AF 2 */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM2         ((uint8_t)0x02U)  /*!< AF2: TIM2 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF2_USART5       ((uint8_t)0x02U)  /*!< AF2: USART5 Alternate Function mapping    */
+#define GPIO_AF2_USART6       ((uint8_t)0x02U)  /*!< AF2: USART6 Alternate Function mapping    */
+#define GPIO_AF2_USART7       ((uint8_t)0x02U)  /*!< AF2: USART7 Alternate Function mapping    */
+#define GPIO_AF2_USART8       ((uint8_t)0x02U)  /*!< AF2: USART8 Alternate Function mapping    */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_TSC          ((uint8_t)0x03U)  /*!< AF3: TSC Alternate Function mapping       */
+#define GPIO_AF3_TIM15        ((uint8_t)0x03U)  /*!< AF3: TIM15 Alternate Function mapping     */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+#define GPIO_AF4_USART4       ((uint8_t)0x04U)  /*!< AF4: USART4 Alternate Function mapping    */
+#define GPIO_AF4_USART3       ((uint8_t)0x04U)  /*!< AF4: USART3 Alternate Function mapping    */
+#define GPIO_AF4_CRS          ((uint8_t)0x04U)  /*!< AF4: CRS Alternate Function mapping       */
+#define GPIO_AF4_CAN          ((uint8_t)0x04U)  /*!< AF4: CAN Alternate Function mapping       */
+#define GPIO_AF4_I2C1         ((uint8_t)0x04U)  /*!< AF4: I2C1 Alternate Function mapping      */
+#define GPIO_AF4_USART5       ((uint8_t)0x04U)  /*!< AF4: USART5 Alternate Function mapping    */
+
+/* AF 5 */
+#define GPIO_AF5_TIM15        ((uint8_t)0x05U)  /*!< AF5: TIM15 Alternate Function mapping     */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+#define GPIO_AF5_SPI2         ((uint8_t)0x05U)  /*!< AF5: SPI2 Alternate Function mapping      */
+#define GPIO_AF5_I2C2         ((uint8_t)0x05U)  /*!< AF5: I2C2 Alternate Function mapping      */
+#define GPIO_AF5_MCO          ((uint8_t)0x05U)  /*!< AF5: MCO Alternate Function mapping       */
+#define GPIO_AF5_USART6       ((uint8_t)0x05U)  /*!< AF5: USART6 Alternate Function mapping    */
+
+/* AF 6 */
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+/* AF 7 */
+#define GPIO_AF7_COMP1        ((uint8_t)0x07U)  /*!< AF7: COMP1 Alternate Function mapping     */
+#define GPIO_AF7_COMP2        ((uint8_t)0x07U)  /*!< AF7: COMP2 Alternate Function mapping     */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x07U)
+
+#endif /* STM32F091xC  || STM32F098xx */
+
+#if defined(STM32F030xC)
+/*--------------------------- STM32F030xC ----------------------------------------------------*/
+/* AF 0 */
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF0_SWDIO        ((uint8_t)0x00U)  /*!< AF0: SWDIO Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1 Alternate Function mapping      */
+#define GPIO_AF0_SPI2         ((uint8_t)0x00U)  /*!< AF0: SPI2 Alternate Function mapping      */
+#define GPIO_AF0_TIM3         ((uint8_t)0x00U)  /*!< AF0: TIM3 Alternate Function mapping      */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_TIM15        ((uint8_t)0x00U)  /*!< AF0: TIM15 Alternate Function mapping     */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+#define GPIO_AF0_USART4       ((uint8_t)0x00U)  /*!< AF0: USART4 Alternate Function mapping    */
+
+/* AF 1 */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+#define GPIO_AF1_TIM15        ((uint8_t)0x01U)  /*!< AF1: TIM15 Alternate Function mapping     */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_USART2       ((uint8_t)0x01U)  /*!< AF1: USART2 Alternate Function mapping    */
+#define GPIO_AF1_USART3       ((uint8_t)0x01U)  /*!< AF1: USART3 Alternate Function mapping    */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_I2C2         ((uint8_t)0x01U)  /*!< AF1: I2C2 Alternate Function mapping      */
+#define GPIO_AF1_SPI2         ((uint8_t)0x01U)  /*!< AF1: SPI2 Alternate Function mapping      */
+
+/* AF 2 */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF2_USART5       ((uint8_t)0x02U)  /*!< AF2: USART5 Alternate Function mapping    */
+#define GPIO_AF2_USART6       ((uint8_t)0x02U)  /*!< AF2: USART6 Alternate Function mapping    */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_TIM15        ((uint8_t)0x03U)  /*!< AF3: TIM15 Alternate Function mapping     */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+#define GPIO_AF4_USART4       ((uint8_t)0x04U)  /*!< AF4: USART4 Alternate Function mapping    */
+#define GPIO_AF4_USART3       ((uint8_t)0x04U)  /*!< AF4: USART3 Alternate Function mapping    */
+#define GPIO_AF4_I2C1         ((uint8_t)0x04U)  /*!< AF4: I2C1 Alternate Function mapping      */
+#define GPIO_AF4_USART5       ((uint8_t)0x04U)  /*!< AF4: USART5 Alternate Function mapping    */
+
+/* AF 5 */
+#define GPIO_AF5_TIM15        ((uint8_t)0x05U)  /*!< AF5: TIM15 Alternate Function mapping     */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+#define GPIO_AF5_SPI2         ((uint8_t)0x05U)  /*!< AF5: SPI2 Alternate Function mapping      */
+#define GPIO_AF5_I2C2         ((uint8_t)0x05U)  /*!< AF5: I2C2 Alternate Function mapping      */
+#define GPIO_AF5_MCO          ((uint8_t)0x05U)  /*!< AF5: MCO Alternate Function mapping       */
+#define GPIO_AF5_USART6       ((uint8_t)0x05U)  /*!< AF5: USART6 Alternate Function mapping    */
+
+/* AF 6 */
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x06U)
+
+#endif /* STM32F030xC */
+
+#if defined (STM32F072xB) || defined (STM32F078xx)
+/*--------------------------- STM32F072xB/STM32F078xx ---------------------------*/
+/* AF 0 */
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF0_SWDIO        ((uint8_t)0x00U)  /*!< AF0: SWDIO Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_CEC          ((uint8_t)0x00U)  /*!< AF0: CEC Alternate Function mapping       */
+#define GPIO_AF0_CRS          ((uint8_t)0x00U)  /*!< AF0: CRS Alternate Function mapping       */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1/I2S1 Alternate Function mapping */
+#define GPIO_AF0_SPI2         ((uint8_t)0x00U)  /*!< AF0: SPI2/I2S2 Alternate Function mapping */
+#define GPIO_AF0_TIM1         ((uint8_t)0x00U)  /*!< AF0: TIM1 Alternate Function mapping      */
+#define GPIO_AF0_TIM3         ((uint8_t)0x00U)  /*!< AF0: TIM3 Alternate Function mapping      */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_TIM15        ((uint8_t)0x00U)  /*!< AF0: TIM15 Alternate Function mapping     */
+#define GPIO_AF0_TIM16        ((uint8_t)0x00U)  /*!< AF0: TIM16 Alternate Function mapping     */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_TSC          ((uint8_t)0x00U)  /*!< AF0: TSC Alternate Function mapping       */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+#define GPIO_AF0_USART2       ((uint8_t)0x00U)  /*!< AF0: USART2 Alternate Function mapping    */
+#define GPIO_AF0_USART3       ((uint8_t)0x00U)  /*!< AF0: USART2 Alternate Function mapping    */
+#define GPIO_AF0_USART4       ((uint8_t)0x00U)  /*!< AF0: USART4 Alternate Function mapping    */
+#define GPIO_AF0_CAN          ((uint8_t)0x00U)  /*!< AF0: CAN Alternate Function mapping       */
+
+/* AF 1 */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+#define GPIO_AF1_TIM15        ((uint8_t)0x01U)  /*!< AF1: TIM15 Alternate Function mapping     */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_USART2       ((uint8_t)0x01U)  /*!< AF1: USART2 Alternate Function mapping    */
+#define GPIO_AF1_USART3       ((uint8_t)0x01U)  /*!< AF1: USART3 Alternate Function mapping    */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+#define GPIO_AF1_CEC          ((uint8_t)0x01U)  /*!< AF1: CEC Alternate Function mapping       */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_I2C2         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_TSC          ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_SPI1         ((uint8_t)0x01U)  /*!< AF1: SPI1 Alternate Function mapping      */
+#define GPIO_AF1_SPI2         ((uint8_t)0x01U)  /*!< AF1: SPI2 Alternate Function mapping      */
+
+/* AF 2 */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM2         ((uint8_t)0x02U)  /*!< AF2: TIM2 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF2_USB          ((uint8_t)0x02U)  /*!< AF2: USB Alternate Function mapping       */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_TSC          ((uint8_t)0x03U)  /*!< AF3: TSC Alternate Function mapping       */
+#define GPIO_AF3_TIM15        ((uint8_t)0x03U)  /*!< AF3: TIM15 Alternate Function mapping     */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+#define GPIO_AF4_USART4       ((uint8_t)0x04U)  /*!< AF4: USART4 Alternate Function mapping    */
+#define GPIO_AF4_USART3       ((uint8_t)0x04U)  /*!< AF4: USART3 Alternate Function mapping    */
+#define GPIO_AF4_CRS          ((uint8_t)0x04U)  /*!< AF4: CRS Alternate Function mapping       */
+#define GPIO_AF4_CAN          ((uint8_t)0x04U)  /*!< AF4: CAN Alternate Function mapping       */
+
+/* AF 5 */
+#define GPIO_AF5_TIM15        ((uint8_t)0x05U)  /*!< AF5: TIM15 Alternate Function mapping     */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+#define GPIO_AF5_SPI2         ((uint8_t)0x05U)  /*!< AF5: SPI2 Alternate Function mapping      */
+#define GPIO_AF5_I2C2         ((uint8_t)0x05U)  /*!< AF5: I2C2 Alternate Function mapping      */
+
+/* AF 6 */
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+/* AF 7 */
+#define GPIO_AF7_COMP1        ((uint8_t)0x07U)  /*!< AF7: COMP1 Alternate Function mapping     */
+#define GPIO_AF7_COMP2        ((uint8_t)0x07U)  /*!< AF7: COMP2 Alternate Function mapping     */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x07U)
+
+#endif /* STM32F072xB || STM32F078xx */
+
+#if defined (STM32F070xB)
+/*---------------------------------- STM32F070xB ---------------------------------------------*/
+/* AF 0 */
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF0_SWDIO        ((uint8_t)0x00U)  /*!< AF0: SWDIO Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1 Alternate Function mapping      */
+#define GPIO_AF0_SPI2         ((uint8_t)0x00U)  /*!< AF0: SPI2 Alternate Function mapping      */
+#define GPIO_AF0_TIM3         ((uint8_t)0x00U)  /*!< AF0: TIM3 Alternate Function mapping      */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_TIM15        ((uint8_t)0x00U)  /*!< AF0: TIM15 Alternate Function mapping     */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+#define GPIO_AF0_USART4       ((uint8_t)0x00U)  /*!< AF0: USART4 Alternate Function mapping    */
+
+/* AF 1 */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+#define GPIO_AF1_TIM15        ((uint8_t)0x01U)  /*!< AF1: TIM15 Alternate Function mapping     */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_USART2       ((uint8_t)0x01U)  /*!< AF1: USART2 Alternate Function mapping    */
+#define GPIO_AF1_USART3       ((uint8_t)0x01U)  /*!< AF1: USART4 Alternate Function mapping    */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_I2C2         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_SPI2         ((uint8_t)0x01U)  /*!< AF1: SPI2 Alternate Function mapping      */
+
+/* AF 2 */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF2_USB          ((uint8_t)0x02U)  /*!< AF2: USB Alternate Function mapping       */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+#define GPIO_AF3_TIM15        ((uint8_t)0x03U)  /*!< AF3: TIM15 Alternate Function mapping     */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+#define GPIO_AF4_USART4       ((uint8_t)0x04U)  /*!< AF4: USART4 Alternate Function mapping    */
+#define GPIO_AF4_USART3       ((uint8_t)0x04U)  /*!< AF4: USART3 Alternate Function mapping    */
+
+/* AF 5 */
+#define GPIO_AF5_TIM15        ((uint8_t)0x05U)  /*!< AF5: TIM15 Alternate Function mapping     */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+#define GPIO_AF5_SPI2         ((uint8_t)0x05U)  /*!< AF5: SPI2 Alternate Function mapping      */
+#define GPIO_AF5_I2C2         ((uint8_t)0x05U)  /*!< AF5: I2C2 Alternate Function mapping      */
+
+/* AF 6 */
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x06U)
+   
+#endif /* STM32F070xB */
+
+#if defined (STM32F042x6) || defined (STM32F048xx)
+/*--------------------------- STM32F042x6/STM32F048xx ---------------------------*/
+/* AF 0 */
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF0_CEC          ((uint8_t)0x00U)  /*!< AF0: CEC Alternate Function mapping       */
+#define GPIO_AF0_CRS          ((uint8_t)0x00U)  /*!< AF0: CRS Alternate Function mapping       */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1/I2S1 Alternate Function mapping */
+#define GPIO_AF0_SPI2         ((uint8_t)0x00U)  /*!< AF0: SPI2/I2S2 Alternate Function mapping */
+#define GPIO_AF0_SWDIO        ((uint8_t)0x00U)  /*!< AF0: SWDIO Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+
+/* AF 1 */
+#define GPIO_AF1_CEC          ((uint8_t)0x01U)  /*!< AF1: CEC Alternate Function mapping       */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_USART2       ((uint8_t)0x01U)  /*!< AF1: USART2 Alternate Function mapping    */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+
+/* AF 2 */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM2         ((uint8_t)0x02U)  /*!< AF2: TIM2 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_USB          ((uint8_t)0x02U)  /*!< AF2: USB Alternate Function mapping       */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+#define GPIO_AF3_TSC          ((uint8_t)0x03U)  /*!< AF3: TSC Alternate Function mapping       */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+#define GPIO_AF4_CAN          ((uint8_t)0x04U)  /*!< AF4: CAN Alternate Function mapping       */
+#define GPIO_AF4_CRS          ((uint8_t)0x04U)  /*!< AF4: CRS Alternate Function mapping       */
+#define GPIO_AF4_I2C1         ((uint8_t)0x04U)  /*!< AF4: I2C1 Alternate Function mapping      */
+
+/* AF 5 */ 
+#define GPIO_AF5_MCO          ((uint8_t)0x05U)  /*!< AF5: MCO Alternate Function mapping       */
+#define GPIO_AF5_I2C1         ((uint8_t)0x05U)  /*!< AF5: I2C1 Alternate Function mapping      */
+#define GPIO_AF5_I2C2         ((uint8_t)0x05U)  /*!< AF5: I2C2 Alternate Function mapping      */
+#define GPIO_AF5_SPI2         ((uint8_t)0x05U)  /*!< AF5: SPI2 Alternate Function mapping      */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+#define GPIO_AF5_USB          ((uint8_t)0x05U)  /*!< AF5: USB Alternate Function mapping       */
+
+/* AF 6 */ 
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x06U)
+
+#endif /* STM32F042x6 || STM32F048xx */
+
+#if defined (STM32F070x6)
+/*--------------------------------------- STM32F070x6 ----------------------------------------*/
+/* AF 0 */
+#define GPIO_AF0_EVENTOUT     ((uint8_t)0x00U)  /*!< AF0: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF0_IR           ((uint8_t)0x00U)  /*!< AF0: IR Alternate Function mapping        */
+#define GPIO_AF0_MCO          ((uint8_t)0x00U)  /*!< AF0: MCO Alternate Function mapping       */
+#define GPIO_AF0_SPI1         ((uint8_t)0x00U)  /*!< AF0: SPI1 Alternate Function mapping      */
+#define GPIO_AF0_SWDIO        ((uint8_t)0x00U)  /*!< AF0: SWDIO Alternate Function mapping     */
+#define GPIO_AF0_SWCLK        ((uint8_t)0x00U)  /*!< AF0: SWCLK Alternate Function mapping     */
+#define GPIO_AF0_TIM14        ((uint8_t)0x00U)  /*!< AF0: TIM14 Alternate Function mapping     */
+#define GPIO_AF0_TIM17        ((uint8_t)0x00U)  /*!< AF0: TIM17 Alternate Function mapping     */
+#define GPIO_AF0_USART1       ((uint8_t)0x00U)  /*!< AF0: USART1 Alternate Function mapping    */
+
+/* AF 1 */
+#define GPIO_AF1_EVENTOUT     ((uint8_t)0x01U)  /*!< AF1: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF1_I2C1         ((uint8_t)0x01U)  /*!< AF1: I2C1 Alternate Function mapping      */
+#define GPIO_AF1_IR           ((uint8_t)0x01U)  /*!< AF1: IR Alternate Function mapping        */
+#define GPIO_AF1_USART1       ((uint8_t)0x01U)  /*!< AF1: USART1 Alternate Function mapping    */
+#define GPIO_AF1_USART2       ((uint8_t)0x01U)  /*!< AF1: USART2 Alternate Function mapping    */
+#define GPIO_AF1_TIM3         ((uint8_t)0x01U)  /*!< AF1: TIM3 Alternate Function mapping      */
+
+/* AF 2 */
+#define GPIO_AF2_EVENTOUT     ((uint8_t)0x02U)  /*!< AF2: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF2_TIM1         ((uint8_t)0x02U)  /*!< AF2: TIM1 Alternate Function mapping      */
+#define GPIO_AF2_TIM16        ((uint8_t)0x02U)  /*!< AF2: TIM16 Alternate Function mapping     */
+#define GPIO_AF2_TIM17        ((uint8_t)0x02U)  /*!< AF2: TIM17 Alternate Function mapping     */
+#define GPIO_AF2_USB          ((uint8_t)0x02U)  /*!< AF2: USB Alternate Function mapping       */
+
+/* AF 3 */
+#define GPIO_AF3_EVENTOUT     ((uint8_t)0x03U)  /*!< AF3: EVENTOUT Alternate Function mapping  */
+#define GPIO_AF3_I2C1         ((uint8_t)0x03U)  /*!< AF3: I2C1 Alternate Function mapping      */
+
+/* AF 4 */
+#define GPIO_AF4_TIM14        ((uint8_t)0x04U)  /*!< AF4: TIM14 Alternate Function mapping     */
+#define GPIO_AF4_I2C1         ((uint8_t)0x04U)  /*!< AF4: I2C1 Alternate Function mapping      */
+
+/* AF 5 */ 
+#define GPIO_AF5_MCO          ((uint8_t)0x05U)  /*!< AF5: MCO Alternate Function mapping       */
+#define GPIO_AF5_I2C1         ((uint8_t)0x05U)  /*!< AF5: I2C1 Alternate Function mapping      */
+#define GPIO_AF5_TIM16        ((uint8_t)0x05U)  /*!< AF5: TIM16 Alternate Function mapping     */
+#define GPIO_AF5_TIM17        ((uint8_t)0x05U)  /*!< AF5: TIM17 Alternate Function mapping     */
+#define GPIO_AF5_USB          ((uint8_t)0x05U)  /*!< AF5: USB Alternate Function mapping       */
+
+/* AF 6 */ 
+#define GPIO_AF6_EVENTOUT     ((uint8_t)0x06U)  /*!< AF6: EVENTOUT Alternate Function mapping  */
+
+#define IS_GPIO_AF(AF)        ((AF) <= (uint8_t)0x06U)
+
+#endif /* STM32F070x6 */
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup GPIOEx_Exported_Macros GPIOEx Exported Macros
+  * @{
+  */
+
+/** @defgroup GPIOEx_Get_Port_Index GPIOEx_Get Port Index
+* @{
+  */
+#if defined(GPIOD) && defined(GPIOE)
+#define GPIO_GET_INDEX(__GPIOx__)    (((__GPIOx__) == (GPIOA))? 0U :\
+                                      ((__GPIOx__) == (GPIOB))? 1U :\
+                                      ((__GPIOx__) == (GPIOC))? 2U :\
+                                      ((__GPIOx__) == (GPIOD))? 3U :\
+                                      ((__GPIOx__) == (GPIOE))? 4U : 5U)
+#endif
+
+#if defined(GPIOD) && !defined(GPIOE)
+#define GPIO_GET_INDEX(__GPIOx__)    (((__GPIOx__) == (GPIOA))? 0U :\
+                                      ((__GPIOx__) == (GPIOB))? 1U :\
+                                      ((__GPIOx__) == (GPIOC))? 2U :\
+                                      ((__GPIOx__) == (GPIOD))? 3U : 5U)
+#endif
+
+#if !defined(GPIOD) && defined(GPIOE)
+#define GPIO_GET_INDEX(__GPIOx__)    (((__GPIOx__) == (GPIOA))? 0U :\
+                                      ((__GPIOx__) == (GPIOB))? 1U :\
+                                      ((__GPIOx__) == (GPIOC))? 2U :\
+                                      ((__GPIOx__) == (GPIOE))? 4U : 5U)
+#endif
+
+#if !defined(GPIOD) && !defined(GPIOE)
+#define GPIO_GET_INDEX(__GPIOx__)    (((__GPIOx__) == (GPIOA))? 0U :\
+                                      ((__GPIOx__) == (GPIOB))? 1U :\
+                                      ((__GPIOx__) == (GPIOC))? 2U : 5U)
+#endif
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/ 
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+  
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_GPIO_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_i2c.h

@@ -0,0 +1,809 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_i2c.h
+  * @author  MCD Application Team
+  * @brief   Header file of I2C HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F0xx_HAL_I2C_H
+#define STM32F0xx_HAL_I2C_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup I2C
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup I2C_Exported_Types I2C Exported Types
+  * @{
+  */
+
+/** @defgroup I2C_Configuration_Structure_definition I2C Configuration Structure definition
+  * @brief  I2C Configuration Structure definition
+  * @{
+  */
+typedef struct
+{
+  uint32_t Timing;              /*!< Specifies the I2C_TIMINGR_register value.
+                                  This parameter calculated by referring to I2C initialization
+                                         section in Reference manual */
+
+  uint32_t OwnAddress1;         /*!< Specifies the first device own address.
+                                  This parameter can be a 7-bit or 10-bit address. */
+
+  uint32_t AddressingMode;      /*!< Specifies if 7-bit or 10-bit addressing mode is selected.
+                                  This parameter can be a value of @ref I2C_ADDRESSING_MODE */
+
+  uint32_t DualAddressMode;     /*!< Specifies if dual addressing mode is selected.
+                                  This parameter can be a value of @ref I2C_DUAL_ADDRESSING_MODE */
+
+  uint32_t OwnAddress2;         /*!< Specifies the second device own address if dual addressing mode is selected
+                                  This parameter can be a 7-bit address. */
+
+  uint32_t OwnAddress2Masks;    /*!< Specifies the acknowledge mask address second device own address if dual addressing mode is selected
+                                  This parameter can be a value of @ref I2C_OWN_ADDRESS2_MASKS */
+
+  uint32_t GeneralCallMode;     /*!< Specifies if general call mode is selected.
+                                  This parameter can be a value of @ref I2C_GENERAL_CALL_ADDRESSING_MODE */
+
+  uint32_t NoStretchMode;       /*!< Specifies if nostretch mode is selected.
+                                  This parameter can be a value of @ref I2C_NOSTRETCH_MODE */
+
+} I2C_InitTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_state_structure_definition HAL state structure definition
+  * @brief  HAL State structure definition
+  * @note  HAL I2C State value coding follow below described bitmap :\n
+  *          b7-b6  Error information\n
+  *             00 : No Error\n
+  *             01 : Abort (Abort user request on going)\n
+  *             10 : Timeout\n
+  *             11 : Error\n
+  *          b5     Peripheral initialization status\n
+  *             0  : Reset (peripheral not initialized)\n
+  *             1  : Init done (peripheral initialized and ready to use. HAL I2C Init function called)\n
+  *          b4     (not used)\n
+  *             x  : Should be set to 0\n
+  *          b3\n
+  *             0  : Ready or Busy (No Listen mode ongoing)\n
+  *             1  : Listen (peripheral in Address Listen Mode)\n
+  *          b2     Intrinsic process state\n
+  *             0  : Ready\n
+  *             1  : Busy (peripheral busy with some configuration or internal operations)\n
+  *          b1     Rx state\n
+  *             0  : Ready (no Rx operation ongoing)\n
+  *             1  : Busy (Rx operation ongoing)\n
+  *          b0     Tx state\n
+  *             0  : Ready (no Tx operation ongoing)\n
+  *             1  : Busy (Tx operation ongoing)
+  * @{
+  */
+typedef enum
+{
+  HAL_I2C_STATE_RESET             = 0x00U,   /*!< Peripheral is not yet Initialized         */
+  HAL_I2C_STATE_READY             = 0x20U,   /*!< Peripheral Initialized and ready for use  */
+  HAL_I2C_STATE_BUSY              = 0x24U,   /*!< An internal process is ongoing            */
+  HAL_I2C_STATE_BUSY_TX           = 0x21U,   /*!< Data Transmission process is ongoing      */
+  HAL_I2C_STATE_BUSY_RX           = 0x22U,   /*!< Data Reception process is ongoing         */
+  HAL_I2C_STATE_LISTEN            = 0x28U,   /*!< Address Listen Mode is ongoing            */
+  HAL_I2C_STATE_BUSY_TX_LISTEN    = 0x29U,   /*!< Address Listen Mode and Data Transmission
+                                                 process is ongoing                         */
+  HAL_I2C_STATE_BUSY_RX_LISTEN    = 0x2AU,   /*!< Address Listen Mode and Data Reception
+                                                 process is ongoing                         */
+  HAL_I2C_STATE_ABORT             = 0x60U,   /*!< Abort user request ongoing                */
+  HAL_I2C_STATE_TIMEOUT           = 0xA0U,   /*!< Timeout state                             */
+  HAL_I2C_STATE_ERROR             = 0xE0U    /*!< Error                                     */
+
+} HAL_I2C_StateTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_mode_structure_definition HAL mode structure definition
+  * @brief  HAL Mode structure definition
+  * @note  HAL I2C Mode value coding follow below described bitmap :\n
+  *          b7     (not used)\n
+  *             x  : Should be set to 0\n
+  *          b6\n
+  *             0  : None\n
+  *             1  : Memory (HAL I2C communication is in Memory Mode)\n
+  *          b5\n
+  *             0  : None\n
+  *             1  : Slave (HAL I2C communication is in Slave Mode)\n
+  *          b4\n
+  *             0  : None\n
+  *             1  : Master (HAL I2C communication is in Master Mode)\n
+  *          b3-b2-b1-b0  (not used)\n
+  *             xxxx : Should be set to 0000
+  * @{
+  */
+typedef enum
+{
+  HAL_I2C_MODE_NONE               = 0x00U,   /*!< No I2C communication on going             */
+  HAL_I2C_MODE_MASTER             = 0x10U,   /*!< I2C communication is in Master Mode       */
+  HAL_I2C_MODE_SLAVE              = 0x20U,   /*!< I2C communication is in Slave Mode        */
+  HAL_I2C_MODE_MEM                = 0x40U    /*!< I2C communication is in Memory Mode       */
+
+} HAL_I2C_ModeTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup I2C_Error_Code_definition I2C Error Code definition
+  * @brief  I2C Error Code definition
+  * @{
+  */
+#define HAL_I2C_ERROR_NONE      (0x00000000U)    /*!< No error              */
+#define HAL_I2C_ERROR_BERR      (0x00000001U)    /*!< BERR error            */
+#define HAL_I2C_ERROR_ARLO      (0x00000002U)    /*!< ARLO error            */
+#define HAL_I2C_ERROR_AF        (0x00000004U)    /*!< ACKF error            */
+#define HAL_I2C_ERROR_OVR       (0x00000008U)    /*!< OVR error             */
+#define HAL_I2C_ERROR_DMA       (0x00000010U)    /*!< DMA transfer error    */
+#define HAL_I2C_ERROR_TIMEOUT   (0x00000020U)    /*!< Timeout error         */
+#define HAL_I2C_ERROR_SIZE      (0x00000040U)    /*!< Size Management error */
+#define HAL_I2C_ERROR_DMA_PARAM (0x00000080U)    /*!< DMA Parameter Error   */
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+#define HAL_I2C_ERROR_INVALID_CALLBACK  (0x00000100U)    /*!< Invalid Callback error */
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
+#define HAL_I2C_ERROR_INVALID_PARAM     (0x00000200U)    /*!< Invalid Parameters error  */
+/**
+  * @}
+  */
+
+/** @defgroup I2C_handle_Structure_definition I2C handle Structure definition
+  * @brief  I2C handle Structure definition
+  * @{
+  */
+typedef struct __I2C_HandleTypeDef
+{
+  I2C_TypeDef                *Instance;      /*!< I2C registers base address                */
+
+  I2C_InitTypeDef            Init;           /*!< I2C communication parameters              */
+
+  uint8_t                    *pBuffPtr;      /*!< Pointer to I2C transfer buffer            */
+
+  uint16_t                   XferSize;       /*!< I2C transfer size                         */
+
+  __IO uint16_t              XferCount;      /*!< I2C transfer counter                      */
+
+  __IO uint32_t              XferOptions;    /*!< I2C sequantial transfer options, this parameter can
+                                                  be a value of @ref I2C_XFEROPTIONS */
+
+  __IO uint32_t              PreviousState;  /*!< I2C communication Previous state          */
+
+  HAL_StatusTypeDef(*XferISR)(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);  /*!< I2C transfer IRQ handler function pointer */
+
+  DMA_HandleTypeDef          *hdmatx;        /*!< I2C Tx DMA handle parameters              */
+
+  DMA_HandleTypeDef          *hdmarx;        /*!< I2C Rx DMA handle parameters              */
+
+  HAL_LockTypeDef            Lock;           /*!< I2C locking object                        */
+
+  __IO HAL_I2C_StateTypeDef  State;          /*!< I2C communication state                   */
+
+  __IO HAL_I2C_ModeTypeDef   Mode;           /*!< I2C communication mode                    */
+
+  __IO uint32_t              ErrorCode;      /*!< I2C Error code                            */
+
+  __IO uint32_t              AddrEventCount; /*!< I2C Address Event counter                 */
+
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+  void (* MasterTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);           /*!< I2C Master Tx Transfer completed callback */
+  void (* MasterRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);           /*!< I2C Master Rx Transfer completed callback */
+  void (* SlaveTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);            /*!< I2C Slave Tx Transfer completed callback  */
+  void (* SlaveRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);            /*!< I2C Slave Rx Transfer completed callback  */
+  void (* ListenCpltCallback)(struct __I2C_HandleTypeDef *hi2c);             /*!< I2C Listen Complete callback              */
+  void (* MemTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);              /*!< I2C Memory Tx Transfer completed callback */
+  void (* MemRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);              /*!< I2C Memory Rx Transfer completed callback */
+  void (* ErrorCallback)(struct __I2C_HandleTypeDef *hi2c);                  /*!< I2C Error callback                        */
+  void (* AbortCpltCallback)(struct __I2C_HandleTypeDef *hi2c);              /*!< I2C Abort callback                        */
+
+  void (* AddrCallback)(struct __I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode);  /*!< I2C Slave Address Match callback */
+
+  void (* MspInitCallback)(struct __I2C_HandleTypeDef *hi2c);                /*!< I2C Msp Init callback                     */
+  void (* MspDeInitCallback)(struct __I2C_HandleTypeDef *hi2c);              /*!< I2C Msp DeInit callback                   */
+
+#endif  /* USE_HAL_I2C_REGISTER_CALLBACKS */
+} I2C_HandleTypeDef;
+
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL I2C Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_I2C_MASTER_TX_COMPLETE_CB_ID      = 0x00U,    /*!< I2C Master Tx Transfer completed callback ID  */
+  HAL_I2C_MASTER_RX_COMPLETE_CB_ID      = 0x01U,    /*!< I2C Master Rx Transfer completed callback ID  */
+  HAL_I2C_SLAVE_TX_COMPLETE_CB_ID       = 0x02U,    /*!< I2C Slave Tx Transfer completed callback ID   */
+  HAL_I2C_SLAVE_RX_COMPLETE_CB_ID       = 0x03U,    /*!< I2C Slave Rx Transfer completed callback ID   */
+  HAL_I2C_LISTEN_COMPLETE_CB_ID         = 0x04U,    /*!< I2C Listen Complete callback ID               */
+  HAL_I2C_MEM_TX_COMPLETE_CB_ID         = 0x05U,    /*!< I2C Memory Tx Transfer callback ID            */
+  HAL_I2C_MEM_RX_COMPLETE_CB_ID         = 0x06U,    /*!< I2C Memory Rx Transfer completed callback ID  */
+  HAL_I2C_ERROR_CB_ID                   = 0x07U,    /*!< I2C Error callback ID                         */
+  HAL_I2C_ABORT_CB_ID                   = 0x08U,    /*!< I2C Abort callback ID                         */
+
+  HAL_I2C_MSPINIT_CB_ID                 = 0x09U,    /*!< I2C Msp Init callback ID                      */
+  HAL_I2C_MSPDEINIT_CB_ID               = 0x0AU     /*!< I2C Msp DeInit callback ID                    */
+
+} HAL_I2C_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL I2C Callback pointer definition
+  */
+typedef  void (*pI2C_CallbackTypeDef)(I2C_HandleTypeDef *hi2c); /*!< pointer to an I2C callback function */
+typedef  void (*pI2C_AddrCallbackTypeDef)(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode); /*!< pointer to an I2C Address Match callback function */
+
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup I2C_Exported_Constants I2C Exported Constants
+  * @{
+  */
+
+/** @defgroup I2C_XFEROPTIONS  I2C Sequential Transfer Options
+  * @{
+  */
+#define I2C_FIRST_FRAME                 ((uint32_t)I2C_SOFTEND_MODE)
+#define I2C_FIRST_AND_NEXT_FRAME        ((uint32_t)(I2C_RELOAD_MODE | I2C_SOFTEND_MODE))
+#define I2C_NEXT_FRAME                  ((uint32_t)(I2C_RELOAD_MODE | I2C_SOFTEND_MODE))
+#define I2C_FIRST_AND_LAST_FRAME        ((uint32_t)I2C_AUTOEND_MODE)
+#define I2C_LAST_FRAME                  ((uint32_t)I2C_AUTOEND_MODE)
+#define I2C_LAST_FRAME_NO_STOP          ((uint32_t)I2C_SOFTEND_MODE)
+
+/* List of XferOptions in usage of :
+ * 1- Restart condition in all use cases (direction change or not)
+ */
+#define  I2C_OTHER_FRAME                (0x000000AAU)
+#define  I2C_OTHER_AND_LAST_FRAME       (0x0000AA00U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_ADDRESSING_MODE I2C Addressing Mode
+  * @{
+  */
+#define I2C_ADDRESSINGMODE_7BIT         (0x00000001U)
+#define I2C_ADDRESSINGMODE_10BIT        (0x00000002U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_DUAL_ADDRESSING_MODE I2C Dual Addressing Mode
+  * @{
+  */
+#define I2C_DUALADDRESS_DISABLE         (0x00000000U)
+#define I2C_DUALADDRESS_ENABLE          I2C_OAR2_OA2EN
+/**
+  * @}
+  */
+
+/** @defgroup I2C_OWN_ADDRESS2_MASKS I2C Own Address2 Masks
+  * @{
+  */
+#define I2C_OA2_NOMASK                  ((uint8_t)0x00U)
+#define I2C_OA2_MASK01                  ((uint8_t)0x01U)
+#define I2C_OA2_MASK02                  ((uint8_t)0x02U)
+#define I2C_OA2_MASK03                  ((uint8_t)0x03U)
+#define I2C_OA2_MASK04                  ((uint8_t)0x04U)
+#define I2C_OA2_MASK05                  ((uint8_t)0x05U)
+#define I2C_OA2_MASK06                  ((uint8_t)0x06U)
+#define I2C_OA2_MASK07                  ((uint8_t)0x07U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_GENERAL_CALL_ADDRESSING_MODE I2C General Call Addressing Mode
+  * @{
+  */
+#define I2C_GENERALCALL_DISABLE         (0x00000000U)
+#define I2C_GENERALCALL_ENABLE          I2C_CR1_GCEN
+/**
+  * @}
+  */
+
+/** @defgroup I2C_NOSTRETCH_MODE I2C No-Stretch Mode
+  * @{
+  */
+#define I2C_NOSTRETCH_DISABLE           (0x00000000U)
+#define I2C_NOSTRETCH_ENABLE            I2C_CR1_NOSTRETCH
+/**
+  * @}
+  */
+
+/** @defgroup I2C_MEMORY_ADDRESS_SIZE I2C Memory Address Size
+  * @{
+  */
+#define I2C_MEMADD_SIZE_8BIT            (0x00000001U)
+#define I2C_MEMADD_SIZE_16BIT           (0x00000002U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_XFERDIRECTION I2C Transfer Direction Master Point of View
+  * @{
+  */
+#define I2C_DIRECTION_TRANSMIT          (0x00000000U)
+#define I2C_DIRECTION_RECEIVE           (0x00000001U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_RELOAD_END_MODE I2C Reload End Mode
+  * @{
+  */
+#define  I2C_RELOAD_MODE                I2C_CR2_RELOAD
+#define  I2C_AUTOEND_MODE               I2C_CR2_AUTOEND
+#define  I2C_SOFTEND_MODE               (0x00000000U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_START_STOP_MODE I2C Start or Stop Mode
+  * @{
+  */
+#define  I2C_NO_STARTSTOP               (0x00000000U)
+#define  I2C_GENERATE_STOP              (uint32_t)(0x80000000U | I2C_CR2_STOP)
+#define  I2C_GENERATE_START_READ        (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN)
+#define  I2C_GENERATE_START_WRITE       (uint32_t)(0x80000000U | I2C_CR2_START)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_Interrupt_configuration_definition I2C Interrupt configuration definition
+  * @brief I2C Interrupt definition
+  *        Elements values convention: 0xXXXXXXXX
+  *           - XXXXXXXX  : Interrupt control mask
+  * @{
+  */
+#define I2C_IT_ERRI                     I2C_CR1_ERRIE
+#define I2C_IT_TCI                      I2C_CR1_TCIE
+#define I2C_IT_STOPI                    I2C_CR1_STOPIE
+#define I2C_IT_NACKI                    I2C_CR1_NACKIE
+#define I2C_IT_ADDRI                    I2C_CR1_ADDRIE
+#define I2C_IT_RXI                      I2C_CR1_RXIE
+#define I2C_IT_TXI                      I2C_CR1_TXIE
+/**
+  * @}
+  */
+
+/** @defgroup I2C_Flag_definition I2C Flag definition
+  * @{
+  */
+#define I2C_FLAG_TXE                    I2C_ISR_TXE
+#define I2C_FLAG_TXIS                   I2C_ISR_TXIS
+#define I2C_FLAG_RXNE                   I2C_ISR_RXNE
+#define I2C_FLAG_ADDR                   I2C_ISR_ADDR
+#define I2C_FLAG_AF                     I2C_ISR_NACKF
+#define I2C_FLAG_STOPF                  I2C_ISR_STOPF
+#define I2C_FLAG_TC                     I2C_ISR_TC
+#define I2C_FLAG_TCR                    I2C_ISR_TCR
+#define I2C_FLAG_BERR                   I2C_ISR_BERR
+#define I2C_FLAG_ARLO                   I2C_ISR_ARLO
+#define I2C_FLAG_OVR                    I2C_ISR_OVR
+#define I2C_FLAG_PECERR                 I2C_ISR_PECERR
+#define I2C_FLAG_TIMEOUT                I2C_ISR_TIMEOUT
+#define I2C_FLAG_ALERT                  I2C_ISR_ALERT
+#define I2C_FLAG_BUSY                   I2C_ISR_BUSY
+#define I2C_FLAG_DIR                    I2C_ISR_DIR
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+
+/** @defgroup I2C_Exported_Macros I2C Exported Macros
+  * @{
+  */
+
+/** @brief Reset I2C handle state.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+#define __HAL_I2C_RESET_HANDLE_STATE(__HANDLE__)                do{                                                   \
+                                                                    (__HANDLE__)->State = HAL_I2C_STATE_RESET;       \
+                                                                    (__HANDLE__)->MspInitCallback = NULL;            \
+                                                                    (__HANDLE__)->MspDeInitCallback = NULL;          \
+                                                                  } while(0)
+#else
+#define __HAL_I2C_RESET_HANDLE_STATE(__HANDLE__)                ((__HANDLE__)->State = HAL_I2C_STATE_RESET)
+#endif
+
+/** @brief  Enable the specified I2C interrupt.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __INTERRUPT__ specifies the interrupt source to enable.
+  *        This parameter can be one of the following values:
+  *            @arg @ref I2C_IT_ERRI  Errors interrupt enable
+  *            @arg @ref I2C_IT_TCI   Transfer complete interrupt enable
+  *            @arg @ref I2C_IT_STOPI STOP detection interrupt enable
+  *            @arg @ref I2C_IT_NACKI NACK received interrupt enable
+  *            @arg @ref I2C_IT_ADDRI Address match interrupt enable
+  *            @arg @ref I2C_IT_RXI   RX interrupt enable
+  *            @arg @ref I2C_IT_TXI   TX interrupt enable
+  *
+  * @retval None
+  */
+#define __HAL_I2C_ENABLE_IT(__HANDLE__, __INTERRUPT__)          ((__HANDLE__)->Instance->CR1 |= (__INTERRUPT__))
+
+/** @brief  Disable the specified I2C interrupt.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __INTERRUPT__ specifies the interrupt source to disable.
+  *        This parameter can be one of the following values:
+  *            @arg @ref I2C_IT_ERRI  Errors interrupt enable
+  *            @arg @ref I2C_IT_TCI   Transfer complete interrupt enable
+  *            @arg @ref I2C_IT_STOPI STOP detection interrupt enable
+  *            @arg @ref I2C_IT_NACKI NACK received interrupt enable
+  *            @arg @ref I2C_IT_ADDRI Address match interrupt enable
+  *            @arg @ref I2C_IT_RXI   RX interrupt enable
+  *            @arg @ref I2C_IT_TXI   TX interrupt enable
+  *
+  * @retval None
+  */
+#define __HAL_I2C_DISABLE_IT(__HANDLE__, __INTERRUPT__)         ((__HANDLE__)->Instance->CR1 &= (~(__INTERRUPT__)))
+
+/** @brief  Check whether the specified I2C interrupt source is enabled or not.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __INTERRUPT__ specifies the I2C interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg @ref I2C_IT_ERRI  Errors interrupt enable
+  *            @arg @ref I2C_IT_TCI   Transfer complete interrupt enable
+  *            @arg @ref I2C_IT_STOPI STOP detection interrupt enable
+  *            @arg @ref I2C_IT_NACKI NACK received interrupt enable
+  *            @arg @ref I2C_IT_ADDRI Address match interrupt enable
+  *            @arg @ref I2C_IT_RXI   RX interrupt enable
+  *            @arg @ref I2C_IT_TXI   TX interrupt enable
+  *
+  * @retval The new state of __INTERRUPT__ (SET or RESET).
+  */
+#define __HAL_I2C_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)      ((((__HANDLE__)->Instance->CR1 & \
+                                                                   (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
+
+/** @brief  Check whether the specified I2C flag is set or not.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __FLAG__ specifies the flag to check.
+  *        This parameter can be one of the following values:
+  *            @arg @ref I2C_FLAG_TXE     Transmit data register empty
+  *            @arg @ref I2C_FLAG_TXIS    Transmit interrupt status
+  *            @arg @ref I2C_FLAG_RXNE    Receive data register not empty
+  *            @arg @ref I2C_FLAG_ADDR    Address matched (slave mode)
+  *            @arg @ref I2C_FLAG_AF      Acknowledge failure received flag
+  *            @arg @ref I2C_FLAG_STOPF   STOP detection flag
+  *            @arg @ref I2C_FLAG_TC      Transfer complete (master mode)
+  *            @arg @ref I2C_FLAG_TCR     Transfer complete reload
+  *            @arg @ref I2C_FLAG_BERR    Bus error
+  *            @arg @ref I2C_FLAG_ARLO    Arbitration lost
+  *            @arg @ref I2C_FLAG_OVR     Overrun/Underrun
+  *            @arg @ref I2C_FLAG_PECERR  PEC error in reception
+  *            @arg @ref I2C_FLAG_TIMEOUT Timeout or Tlow detection flag
+  *            @arg @ref I2C_FLAG_ALERT   SMBus alert
+  *            @arg @ref I2C_FLAG_BUSY    Bus busy
+  *            @arg @ref I2C_FLAG_DIR     Transfer direction (slave mode)
+  *
+  * @retval The new state of __FLAG__ (SET or RESET).
+  */
+#define I2C_FLAG_MASK  (0x0001FFFFU)
+#define __HAL_I2C_GET_FLAG(__HANDLE__, __FLAG__) (((((__HANDLE__)->Instance->ISR) & \
+                                                    (__FLAG__)) == (__FLAG__)) ? SET : RESET)
+
+/** @brief  Clear the I2C pending flags which are cleared by writing 1 in a specific bit.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __FLAG__ specifies the flag to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg @ref I2C_FLAG_TXE     Transmit data register empty
+  *            @arg @ref I2C_FLAG_ADDR    Address matched (slave mode)
+  *            @arg @ref I2C_FLAG_AF      Acknowledge failure received flag
+  *            @arg @ref I2C_FLAG_STOPF   STOP detection flag
+  *            @arg @ref I2C_FLAG_BERR    Bus error
+  *            @arg @ref I2C_FLAG_ARLO    Arbitration lost
+  *            @arg @ref I2C_FLAG_OVR     Overrun/Underrun
+  *            @arg @ref I2C_FLAG_PECERR  PEC error in reception
+  *            @arg @ref I2C_FLAG_TIMEOUT Timeout or Tlow detection flag
+  *            @arg @ref I2C_FLAG_ALERT   SMBus alert
+  *
+  * @retval None
+  */
+#define __HAL_I2C_CLEAR_FLAG(__HANDLE__, __FLAG__) (((__FLAG__) == I2C_FLAG_TXE) ? ((__HANDLE__)->Instance->ISR |= (__FLAG__)) \
+                                                    : ((__HANDLE__)->Instance->ICR = (__FLAG__)))
+
+/** @brief  Enable the specified I2C peripheral.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#define __HAL_I2C_ENABLE(__HANDLE__)                            (SET_BIT((__HANDLE__)->Instance->CR1,  I2C_CR1_PE))
+
+/** @brief  Disable the specified I2C peripheral.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#define __HAL_I2C_DISABLE(__HANDLE__)                           (CLEAR_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))
+
+/** @brief  Generate a Non-Acknowledge I2C peripheral in Slave mode.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#define __HAL_I2C_GENERATE_NACK(__HANDLE__)                     (SET_BIT((__HANDLE__)->Instance->CR2, I2C_CR2_NACK))
+/**
+  * @}
+  */
+
+/* Include I2C HAL Extended module */
+#include "stm32f0xx_hal_i2c_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup I2C_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup I2C_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+/* Initialization and de-initialization functions******************************/
+HAL_StatusTypeDef HAL_I2C_Init(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2C_DeInit(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MspInit(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MspDeInit(I2C_HandleTypeDef *hi2c);
+
+/* Callbacks Register/UnRegister functions  ***********************************/
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+HAL_StatusTypeDef HAL_I2C_RegisterCallback(I2C_HandleTypeDef *hi2c, HAL_I2C_CallbackIDTypeDef CallbackID,
+                                           pI2C_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_I2C_UnRegisterCallback(I2C_HandleTypeDef *hi2c, HAL_I2C_CallbackIDTypeDef CallbackID);
+
+HAL_StatusTypeDef HAL_I2C_RegisterAddrCallback(I2C_HandleTypeDef *hi2c, pI2C_AddrCallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_I2C_UnRegisterAddrCallback(I2C_HandleTypeDef *hi2c);
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @addtogroup I2C_Exported_Functions_Group2 Input and Output operation functions
+  * @{
+  */
+/* IO operation functions  ****************************************************/
+/******* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_I2C_Master_Transmit(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size,
+                                          uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Master_Receive(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size,
+                                         uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Slave_Receive(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Mem_Write(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                    uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Mem_Read(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                   uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_IsDeviceReady(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint32_t Trials,
+                                        uint32_t Timeout);
+
+/******* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_I2C_Master_Transmit_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                             uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Master_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                            uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Receive_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Write_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                       uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Read_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                      uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Transmit_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                                 uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                                uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Transmit_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+                                                uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Receive_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+                                               uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_EnableListen_IT(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2C_DisableListen_IT(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2C_Master_Abort_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress);
+
+/******* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_I2C_Master_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                              uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Master_Receive_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                             uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Receive_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Write_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                        uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Read_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                       uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                                  uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Receive_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                                 uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+                                                 uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Receive_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+                                                uint32_t XferOptions);
+/**
+  * @}
+  */
+
+/** @addtogroup I2C_IRQ_Handler_and_Callbacks IRQ Handler and Callbacks
+  * @{
+  */
+/******* I2C IRQHandler and Callbacks used in non blocking modes (Interrupt and DMA) */
+void HAL_I2C_EV_IRQHandler(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_ER_IRQHandler(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MasterTxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MasterRxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_SlaveTxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_SlaveRxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_AddrCallback(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode);
+void HAL_I2C_ListenCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MemTxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MemRxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_ErrorCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_AbortCpltCallback(I2C_HandleTypeDef *hi2c);
+/**
+  * @}
+  */
+
+/** @addtogroup I2C_Exported_Functions_Group3 Peripheral State, Mode and Error functions
+  * @{
+  */
+/* Peripheral State, Mode and Error functions  *********************************/
+HAL_I2C_StateTypeDef HAL_I2C_GetState(I2C_HandleTypeDef *hi2c);
+HAL_I2C_ModeTypeDef  HAL_I2C_GetMode(I2C_HandleTypeDef *hi2c);
+uint32_t             HAL_I2C_GetError(I2C_HandleTypeDef *hi2c);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup I2C_Private_Constants I2C Private Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup I2C_Private_Macro I2C Private Macros
+  * @{
+  */
+
+#define IS_I2C_ADDRESSING_MODE(MODE)    (((MODE) == I2C_ADDRESSINGMODE_7BIT) || \
+                                         ((MODE) == I2C_ADDRESSINGMODE_10BIT))
+
+#define IS_I2C_DUAL_ADDRESS(ADDRESS)    (((ADDRESS) == I2C_DUALADDRESS_DISABLE) || \
+                                         ((ADDRESS) == I2C_DUALADDRESS_ENABLE))
+
+#define IS_I2C_OWN_ADDRESS2_MASK(MASK)  (((MASK) == I2C_OA2_NOMASK)  || \
+                                         ((MASK) == I2C_OA2_MASK01) || \
+                                         ((MASK) == I2C_OA2_MASK02) || \
+                                         ((MASK) == I2C_OA2_MASK03) || \
+                                         ((MASK) == I2C_OA2_MASK04) || \
+                                         ((MASK) == I2C_OA2_MASK05) || \
+                                         ((MASK) == I2C_OA2_MASK06) || \
+                                         ((MASK) == I2C_OA2_MASK07))
+
+#define IS_I2C_GENERAL_CALL(CALL)       (((CALL) == I2C_GENERALCALL_DISABLE) || \
+                                         ((CALL) == I2C_GENERALCALL_ENABLE))
+
+#define IS_I2C_NO_STRETCH(STRETCH)      (((STRETCH) == I2C_NOSTRETCH_DISABLE) || \
+                                         ((STRETCH) == I2C_NOSTRETCH_ENABLE))
+
+#define IS_I2C_MEMADD_SIZE(SIZE)        (((SIZE) == I2C_MEMADD_SIZE_8BIT) || \
+                                         ((SIZE) == I2C_MEMADD_SIZE_16BIT))
+
+#define IS_TRANSFER_MODE(MODE)          (((MODE) == I2C_RELOAD_MODE)   || \
+                                         ((MODE) == I2C_AUTOEND_MODE) || \
+                                         ((MODE) == I2C_SOFTEND_MODE))
+
+#define IS_TRANSFER_REQUEST(REQUEST)    (((REQUEST) == I2C_GENERATE_STOP)        || \
+                                         ((REQUEST) == I2C_GENERATE_START_READ)  || \
+                                         ((REQUEST) == I2C_GENERATE_START_WRITE) || \
+                                         ((REQUEST) == I2C_NO_STARTSTOP))
+
+#define IS_I2C_TRANSFER_OPTIONS_REQUEST(REQUEST)  (((REQUEST) == I2C_FIRST_FRAME)          || \
+                                                   ((REQUEST) == I2C_FIRST_AND_NEXT_FRAME) || \
+                                                   ((REQUEST) == I2C_NEXT_FRAME)           || \
+                                                   ((REQUEST) == I2C_FIRST_AND_LAST_FRAME) || \
+                                                   ((REQUEST) == I2C_LAST_FRAME)           || \
+                                                   ((REQUEST) == I2C_LAST_FRAME_NO_STOP)   || \
+                                                   IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(REQUEST))
+
+#define IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(REQUEST) (((REQUEST) == I2C_OTHER_FRAME)     || \
+                                                        ((REQUEST) == I2C_OTHER_AND_LAST_FRAME))
+
+#define I2C_RESET_CR2(__HANDLE__)                 ((__HANDLE__)->Instance->CR2 &= \
+                                                   (uint32_t)~((uint32_t)(I2C_CR2_SADD | I2C_CR2_HEAD10R | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_RD_WRN)))
+
+#define I2C_GET_ADDR_MATCH(__HANDLE__)            ((uint16_t)(((__HANDLE__)->Instance->ISR & I2C_ISR_ADDCODE) >> 16U))
+#define I2C_GET_DIR(__HANDLE__)                   ((uint8_t)(((__HANDLE__)->Instance->ISR & I2C_ISR_DIR) >> 16U))
+#define I2C_GET_STOP_MODE(__HANDLE__)             ((__HANDLE__)->Instance->CR2 & I2C_CR2_AUTOEND)
+#define I2C_GET_OWN_ADDRESS1(__HANDLE__)          ((uint16_t)((__HANDLE__)->Instance->OAR1 & I2C_OAR1_OA1))
+#define I2C_GET_OWN_ADDRESS2(__HANDLE__)          ((uint16_t)((__HANDLE__)->Instance->OAR2 & I2C_OAR2_OA2))
+
+#define IS_I2C_OWN_ADDRESS1(ADDRESS1)             ((ADDRESS1) <= 0x000003FFU)
+#define IS_I2C_OWN_ADDRESS2(ADDRESS2)             ((ADDRESS2) <= (uint16_t)0x00FFU)
+
+#define I2C_MEM_ADD_MSB(__ADDRESS__)              ((uint8_t)((uint16_t)(((uint16_t)((__ADDRESS__) & \
+                                                                         (uint16_t)(0xFF00U))) >> 8U)))
+#define I2C_MEM_ADD_LSB(__ADDRESS__)              ((uint8_t)((uint16_t)((__ADDRESS__) & (uint16_t)(0x00FFU))))
+
+#define I2C_GENERATE_START(__ADDMODE__,__ADDRESS__) (((__ADDMODE__) == I2C_ADDRESSINGMODE_7BIT) ? (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | (I2C_CR2_START) | (I2C_CR2_AUTOEND)) & (~I2C_CR2_RD_WRN)) : \
+                                                     (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | (I2C_CR2_ADD10) | (I2C_CR2_START)) & (~I2C_CR2_RD_WRN)))
+
+#define I2C_CHECK_FLAG(__ISR__, __FLAG__)         ((((__ISR__) &  ((__FLAG__) & I2C_FLAG_MASK)) == \
+                                                    ((__FLAG__) & I2C_FLAG_MASK)) ? SET : RESET)
+#define I2C_CHECK_IT_SOURCE(__CR1__, __IT__)      ((((__CR1__) & (__IT__)) == (__IT__)) ? SET : RESET)
+/**
+  * @}
+  */
+
+/* Private Functions ---------------------------------------------------------*/
+/** @defgroup I2C_Private_Functions I2C Private Functions
+  * @{
+  */
+/* Private functions are defined in stm32f0xx_hal_i2c.c file */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* STM32F0xx_HAL_I2C_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_i2c_ex.h

@@ -0,0 +1,174 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_i2c_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of I2C HAL Extended module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F0xx_HAL_I2C_EX_H
+#define STM32F0xx_HAL_I2C_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup I2CEx
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup I2CEx_Exported_Constants I2C Extended Exported Constants
+  * @{
+  */
+
+/** @defgroup I2CEx_Analog_Filter I2C Extended Analog Filter
+  * @{
+  */
+#define I2C_ANALOGFILTER_ENABLE         0x00000000U
+#define I2C_ANALOGFILTER_DISABLE        I2C_CR1_ANFOFF
+/**
+  * @}
+  */
+
+/** @defgroup I2CEx_FastModePlus I2C Extended Fast Mode Plus
+  * @{
+  */
+#define I2C_FMP_NOT_SUPPORTED           0xAAAA0000U                                     /*!< Fast Mode Plus not supported       */
+#if defined(SYSCFG_CFGR1_I2C_FMP_PA9)
+#define I2C_FASTMODEPLUS_PA9            SYSCFG_CFGR1_I2C_FMP_PA9                        /*!< Enable Fast Mode Plus on PA9       */
+#define I2C_FASTMODEPLUS_PA10           SYSCFG_CFGR1_I2C_FMP_PA10                       /*!< Enable Fast Mode Plus on PA10      */
+#else
+#define I2C_FASTMODEPLUS_PA9            (uint32_t)(0x00000001U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus PA9 not supported   */
+#define I2C_FASTMODEPLUS_PA10           (uint32_t)(0x00000002U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus PA10 not supported  */
+#endif
+#define I2C_FASTMODEPLUS_PB6            SYSCFG_CFGR1_I2C_FMP_PB6                        /*!< Enable Fast Mode Plus on PB6       */
+#define I2C_FASTMODEPLUS_PB7            SYSCFG_CFGR1_I2C_FMP_PB7                        /*!< Enable Fast Mode Plus on PB7       */
+#define I2C_FASTMODEPLUS_PB8            SYSCFG_CFGR1_I2C_FMP_PB8                        /*!< Enable Fast Mode Plus on PB8       */
+#define I2C_FASTMODEPLUS_PB9            SYSCFG_CFGR1_I2C_FMP_PB9                        /*!< Enable Fast Mode Plus on PB9       */
+#if defined(SYSCFG_CFGR1_I2C_FMP_I2C1)
+#define I2C_FASTMODEPLUS_I2C1           SYSCFG_CFGR1_I2C_FMP_I2C1                       /*!< Enable Fast Mode Plus on I2C1 pins */
+#else
+#define I2C_FASTMODEPLUS_I2C1           (uint32_t)(0x00000100U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus I2C1 not supported  */
+#endif
+#if defined(SYSCFG_CFGR1_I2C_FMP_I2C2)
+#define I2C_FASTMODEPLUS_I2C2           SYSCFG_CFGR1_I2C_FMP_I2C2                       /*!< Enable Fast Mode Plus on I2C2 pins */
+#else
+#define I2C_FASTMODEPLUS_I2C2           (uint32_t)(0x00000200U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus I2C2 not supported  */
+#endif
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup I2CEx_Exported_Functions I2C Extended Exported Functions
+  * @{
+  */
+
+/** @addtogroup I2CEx_Exported_Functions_Group1 Extended features functions
+  * @brief    Extended features functions
+  * @{
+  */
+
+/* Peripheral Control functions  ************************************************/
+HAL_StatusTypeDef HAL_I2CEx_ConfigAnalogFilter(I2C_HandleTypeDef *hi2c,
+                                                              uint32_t AnalogFilter);
+HAL_StatusTypeDef HAL_I2CEx_ConfigDigitalFilter(I2C_HandleTypeDef *hi2c,
+                                                               uint32_t DigitalFilter);
+#if defined(I2C_CR1_WUPEN)
+HAL_StatusTypeDef HAL_I2CEx_EnableWakeUp(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2CEx_DisableWakeUp(I2C_HandleTypeDef *hi2c);
+#endif
+void HAL_I2CEx_EnableFastModePlus(uint32_t ConfigFastModePlus);
+void HAL_I2CEx_DisableFastModePlus(uint32_t ConfigFastModePlus);
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup I2CEx_Private_Constants I2C Extended Private Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup I2CEx_Private_Macro I2C Extended Private Macros
+  * @{
+  */
+#define IS_I2C_ANALOG_FILTER(FILTER)    (((FILTER) == I2C_ANALOGFILTER_ENABLE) || \
+                                                        ((FILTER) == I2C_ANALOGFILTER_DISABLE))
+
+#define IS_I2C_DIGITAL_FILTER(FILTER)   ((FILTER) <= 0x0000000FU)
+
+#define IS_I2C_FASTMODEPLUS(__CONFIG__) ((((__CONFIG__) & I2C_FMP_NOT_SUPPORTED) != I2C_FMP_NOT_SUPPORTED) && \
+                                                        ((((__CONFIG__) & (I2C_FASTMODEPLUS_PA9))  == I2C_FASTMODEPLUS_PA9)     || \
+                                                         (((__CONFIG__) & (I2C_FASTMODEPLUS_PA10)) == I2C_FASTMODEPLUS_PA10)    || \
+                                                         (((__CONFIG__) & (I2C_FASTMODEPLUS_PB6))  == I2C_FASTMODEPLUS_PB6)     || \
+                                                         (((__CONFIG__) & (I2C_FASTMODEPLUS_PB7))  == I2C_FASTMODEPLUS_PB7)     || \
+                                                         (((__CONFIG__) & (I2C_FASTMODEPLUS_PB8))  == I2C_FASTMODEPLUS_PB8)     || \
+                                                         (((__CONFIG__) & (I2C_FASTMODEPLUS_PB9))  == I2C_FASTMODEPLUS_PB9)     || \
+                                                         (((__CONFIG__) & (I2C_FASTMODEPLUS_I2C1)) == I2C_FASTMODEPLUS_I2C1)    || \
+                                                         (((__CONFIG__) & (I2C_FASTMODEPLUS_I2C2)) == I2C_FASTMODEPLUS_I2C2)))
+/**
+  * @}
+  */
+
+/* Private Functions ---------------------------------------------------------*/
+/** @defgroup I2CEx_Private_Functions I2C Extended Private Functions
+  * @{
+  */
+/* Private functions are defined in stm32f0xx_hal_i2c_ex.c file */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F0xx_HAL_I2C_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_pwr.h

@@ -0,0 +1,189 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_pwr.h
+  * @author  MCD Application Team
+  * @brief   Header file of PWR HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_PWR_H
+#define __STM32F0xx_HAL_PWR_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup PWR PWR
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup PWR_Exported_Constants PWR Exported Constants
+  * @{
+  */ 
+
+/** @defgroup PWR_Regulator_state_in_STOP_mode PWR Regulator state in STOP mode
+  * @{
+  */
+#define PWR_MAINREGULATOR_ON                        (0x00000000U)
+#define PWR_LOWPOWERREGULATOR_ON                    PWR_CR_LPDS
+
+#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
+                                     ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))
+/**
+  * @}
+  */
+
+/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
+  * @{
+  */
+#define PWR_SLEEPENTRY_WFI              ((uint8_t)0x01U)
+#define PWR_SLEEPENTRY_WFE              ((uint8_t)0x02U)
+#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))
+/**
+  * @}
+  */
+
+/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
+  * @{
+  */
+#define PWR_STOPENTRY_WFI               ((uint8_t)0x01U)
+#define PWR_STOPENTRY_WFE               ((uint8_t)0x02U)
+#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE))
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup PWR_Exported_Macro PWR Exported Macro
+  * @{
+  */
+
+/** @brief  Check PWR flag is set or not.
+  * @param  __FLAG__ specifies the flag to check.
+  *           This parameter can be one of the following values:
+  *            @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
+  *                  was received from the WKUP pin or from the RTC alarm (Alarm A),
+  *                  RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
+  *                  An additional wakeup event is detected if the WKUP pin is enabled
+  *                  (by setting the EWUP bit) when the WKUP pin level is already high.
+  *            @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
+  *                  resumed from StandBy mode.
+  *            @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
+  *                  by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode
+  *                  For this reason, this bit is equal to 0 after Standby or reset
+  *                  until the PVDE bit is set. 
+  *                  Warning: this Flag is not available on STM32F030x8 products
+  *            @arg PWR_FLAG_VREFINTRDY: This flag indicates that the internal reference
+  *                  voltage VREFINT is ready.
+  *                  Warning: this Flag is not available on STM32F030x8 products
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clear the PWR's pending flags.
+  * @param  __FLAG__ specifies the flag to clear.
+  *          This parameter can be one of the following values:
+  *            @arg PWR_FLAG_WU: Wake Up flag
+  *            @arg PWR_FLAG_SB: StandBy flag
+  */
+#define __HAL_PWR_CLEAR_FLAG(__FLAG__) (PWR->CR |=  (__FLAG__) << 2U)
+
+
+/**
+  * @}
+  */
+
+/* Include PWR HAL Extension module */
+#include "stm32f0xx_hal_pwr_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup PWR_Exported_Functions PWR Exported Functions
+  * @{
+  */
+  
+/** @addtogroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions 
+  * @{
+  */
+
+/* Initialization and de-initialization functions *****************************/
+void HAL_PWR_DeInit(void);
+
+/**
+  * @}
+  */
+
+/** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions 
+  * @{
+  */
+
+/* Peripheral Control functions  **********************************************/
+void HAL_PWR_EnableBkUpAccess(void);
+void HAL_PWR_DisableBkUpAccess(void);
+
+/* WakeUp pins configuration functions ****************************************/
+void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx);
+void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);
+
+/* Low Power modes configuration functions ************************************/
+void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
+void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
+void HAL_PWR_EnterSTANDBYMode(void);
+
+void HAL_PWR_EnableSleepOnExit(void);
+void HAL_PWR_DisableSleepOnExit(void);
+void HAL_PWR_EnableSEVOnPend(void);
+void HAL_PWR_DisableSEVOnPend(void);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* __STM32F0xx_HAL_PWR_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_pwr_ex.h

@@ -0,0 +1,459 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_pwr_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of PWR HAL Extension module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_PWR_EX_H
+#define __STM32F0xx_HAL_PWR_EX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup PWREx
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/ 
+
+/** @defgroup PWREx_Exported_Types PWREx Exported Types
+ *  @{
+ */
+
+#if defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || \
+    defined (STM32F091xC)
+
+/**
+  * @brief  PWR PVD configuration structure definition
+  */
+typedef struct
+{
+  uint32_t PVDLevel;   /*!< PVDLevel: Specifies the PVD detection level
+                            This parameter can be a value of @ref PWREx_PVD_detection_level */
+
+  uint32_t Mode;       /*!< Mode: Specifies the operating mode for the selected pins.
+                            This parameter can be a value of @ref PWREx_PVD_Mode */
+}PWR_PVDTypeDef;
+
+#endif /* defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || */
+       /* defined (STM32F071xB) || defined (STM32F072xB) || */
+       /* defined (STM32F091xC) */
+/**
+  * @}
+  */
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup PWREx_Exported_Constants PWREx Exported Constants
+  * @{
+  */
+
+
+/** @defgroup PWREx_WakeUp_Pins PWREx Wakeup Pins
+  * @{
+  */
+#if defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+    defined (STM32F091xC) || defined (STM32F098xx)
+#define PWR_WAKEUP_PIN1                     ((uint32_t)PWR_CSR_EWUP1)
+#define PWR_WAKEUP_PIN2                     ((uint32_t)PWR_CSR_EWUP2)
+#define PWR_WAKEUP_PIN3                     ((uint32_t)PWR_CSR_EWUP3)
+#define PWR_WAKEUP_PIN4                     ((uint32_t)PWR_CSR_EWUP4)
+#define PWR_WAKEUP_PIN5                     ((uint32_t)PWR_CSR_EWUP5)
+#define PWR_WAKEUP_PIN6                     ((uint32_t)PWR_CSR_EWUP6)
+#define PWR_WAKEUP_PIN7                     ((uint32_t)PWR_CSR_EWUP7)
+#define PWR_WAKEUP_PIN8                     ((uint32_t)PWR_CSR_EWUP8)
+
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+                                ((PIN) == PWR_WAKEUP_PIN2) || \
+                                ((PIN) == PWR_WAKEUP_PIN3) || \
+                                ((PIN) == PWR_WAKEUP_PIN4) || \
+                                ((PIN) == PWR_WAKEUP_PIN5) || \
+                                ((PIN) == PWR_WAKEUP_PIN6) || \
+                                ((PIN) == PWR_WAKEUP_PIN7) || \
+                                ((PIN) == PWR_WAKEUP_PIN8))
+
+#elif defined(STM32F030xC) || defined (STM32F070xB)
+#define PWR_WAKEUP_PIN1                     ((uint32_t)PWR_CSR_EWUP1)
+#define PWR_WAKEUP_PIN2                     ((uint32_t)PWR_CSR_EWUP2)
+#define PWR_WAKEUP_PIN4                     ((uint32_t)PWR_CSR_EWUP4)
+#define PWR_WAKEUP_PIN5                     ((uint32_t)PWR_CSR_EWUP5)
+#define PWR_WAKEUP_PIN6                     ((uint32_t)PWR_CSR_EWUP6)
+#define PWR_WAKEUP_PIN7                     ((uint32_t)PWR_CSR_EWUP7)
+
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+                                ((PIN) == PWR_WAKEUP_PIN2) || \
+                                ((PIN) == PWR_WAKEUP_PIN4) || \
+                                ((PIN) == PWR_WAKEUP_PIN5) || \
+                                ((PIN) == PWR_WAKEUP_PIN6) || \
+                                ((PIN) == PWR_WAKEUP_PIN7))
+
+#elif defined(STM32F042x6) || defined (STM32F048xx)
+#define PWR_WAKEUP_PIN1                     ((uint32_t)PWR_CSR_EWUP1)
+#define PWR_WAKEUP_PIN2                     ((uint32_t)PWR_CSR_EWUP2)
+#define PWR_WAKEUP_PIN4                     ((uint32_t)PWR_CSR_EWUP4)
+#define PWR_WAKEUP_PIN6                     ((uint32_t)PWR_CSR_EWUP6)
+#define PWR_WAKEUP_PIN7                     ((uint32_t)PWR_CSR_EWUP7)
+
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+                                ((PIN) == PWR_WAKEUP_PIN2) || \
+                                ((PIN) == PWR_WAKEUP_PIN4) || \
+                                ((PIN) == PWR_WAKEUP_PIN6) || \
+                                ((PIN) == PWR_WAKEUP_PIN7))
+
+#else
+#define PWR_WAKEUP_PIN1                     ((uint32_t)PWR_CSR_EWUP1)
+#define PWR_WAKEUP_PIN2                     ((uint32_t)PWR_CSR_EWUP2)
+
+
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+                                ((PIN) == PWR_WAKEUP_PIN2))
+
+#endif
+
+/**
+  * @}
+  */
+
+/** @defgroup PWREx_EXTI_Line PWREx EXTI Line
+  * @{
+  */
+#if defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || \
+    defined (STM32F091xC)
+
+#define PWR_EXTI_LINE_PVD                   ((uint32_t)EXTI_IMR_MR16)  /*!< External interrupt line 16 Connected to the PVD EXTI Line */
+
+#endif /* defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || */
+       /* defined (STM32F071xB) || defined (STM32F072xB) || */
+       /* defined (STM32F091xC) */
+      
+#if defined (STM32F042x6) || defined (STM32F048xx) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+    defined (STM32F091xC) || defined (STM32F098xx)
+
+#define PWR_EXTI_LINE_VDDIO2                ((uint32_t)EXTI_IMR_MR31)  /*!< External interrupt line 31 Connected to the Vddio2 Monitor EXTI Line */
+
+#endif /* defined (STM32F042x6) || defined (STM32F048xx) ||\
+          defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+          defined (STM32F091xC) || defined (STM32F098xx) ||*/
+/**
+  * @}
+  */
+
+#if defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || \
+    defined (STM32F091xC)
+/** @defgroup PWREx_PVD_detection_level PWREx PVD detection level
+  * @{
+  */
+#define PWR_PVDLEVEL_0                      PWR_CR_PLS_LEV0
+#define PWR_PVDLEVEL_1                      PWR_CR_PLS_LEV1
+#define PWR_PVDLEVEL_2                      PWR_CR_PLS_LEV2
+#define PWR_PVDLEVEL_3                      PWR_CR_PLS_LEV3
+#define PWR_PVDLEVEL_4                      PWR_CR_PLS_LEV4
+#define PWR_PVDLEVEL_5                      PWR_CR_PLS_LEV5
+#define PWR_PVDLEVEL_6                      PWR_CR_PLS_LEV6
+#define PWR_PVDLEVEL_7                      PWR_CR_PLS_LEV7
+#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7))
+/**
+  * @}
+  */
+
+/** @defgroup PWREx_PVD_Mode PWREx PVD Mode
+  * @{
+  */
+#define PWR_PVD_MODE_NORMAL                 (0x00000000U)   /*!< basic mode is used */
+#define PWR_PVD_MODE_IT_RISING              (0x00010001U)   /*!< External Interrupt Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_IT_FALLING             (0x00010002U)   /*!< External Interrupt Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_IT_RISING_FALLING      (0x00010003U)   /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING           (0x00020001U)   /*!< Event Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_EVENT_FALLING          (0x00020002U)   /*!< Event Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING_FALLING   (0x00020003U)   /*!< Event Mode with Rising/Falling edge trigger detection */
+
+#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \
+                              ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \
+                              ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \
+                              ((MODE) == PWR_PVD_MODE_NORMAL))
+/**
+  * @}
+  */
+#endif /* defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || */
+       /* defined (STM32F071xB) || defined (STM32F072xB) || */
+       /* defined (STM32F091xC) */
+
+/** @defgroup PWREx_Flag PWREx Flag
+  * @{
+  */
+#if defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || \
+    defined (STM32F091xC)
+
+#define PWR_FLAG_WU                         PWR_CSR_WUF
+#define PWR_FLAG_SB                         PWR_CSR_SBF
+#define PWR_FLAG_PVDO                       PWR_CSR_PVDO
+#define PWR_FLAG_VREFINTRDY                 PWR_CSR_VREFINTRDYF
+#elif defined (STM32F070x6) || defined (STM32F070xB) || defined (STM32F030xC)
+#define PWR_FLAG_WU                         PWR_CSR_WUF
+#define PWR_FLAG_SB                         PWR_CSR_SBF
+#define PWR_FLAG_VREFINTRDY                 PWR_CSR_VREFINTRDYF
+#else
+#define PWR_FLAG_WU                         PWR_CSR_WUF
+#define PWR_FLAG_SB                         PWR_CSR_SBF
+
+#endif /* defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || */
+       /* defined (STM32F071xB) || defined (STM32F072xB) || */
+       /* defined (STM32F091xC) */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */ 
+  
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup PWREx_Exported_Macros PWREx Exported Macros
+  * @{
+  */
+#if defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || \
+    defined (STM32F091xC)
+/**
+  * @brief Enable interrupt on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_IT()      (EXTI->IMR |= (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Disable interrupt on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_IT()     (EXTI->IMR &= ~(PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Enable event on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT()   (EXTI->EMR |= (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Disable event on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT()  (EXTI->EMR &= ~(PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Disable the PVD Extended Interrupt Rising Trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE()  CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable the PVD Extended Interrupt Falling Trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE()  CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger.
+  * @retval None
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE()  __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE();
+
+
+/**
+  * @brief  PVD EXTI line configuration: set falling edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE()  EXTI->FTSR |= (PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief  PVD EXTI line configuration: set rising edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE()   EXTI->RTSR |= (PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief  Enable the PVD Extended Interrupt Rising & Falling Trigger.
+  * @retval None
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE()   __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();
+
+/**
+  * @brief Check whether the specified PVD EXTI interrupt flag is set or not.
+  * @retval EXTI PVD Line Status.
+  */
+#define __HAL_PWR_PVD_EXTI_GET_FLAG()       (EXTI->PR & (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Clear the PVD EXTI flag.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG()     (EXTI->PR = (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Generate a Software interrupt on selected EXTI line.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT()  (EXTI->SWIER |= (PWR_EXTI_LINE_PVD))
+
+#endif /* defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || */
+       /* defined (STM32F071xB) || defined (STM32F072xB) || */
+       /* defined (STM32F091xC) */
+
+
+#if defined (STM32F042x6) || defined (STM32F048xx) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+    defined (STM32F091xC) || defined (STM32F098xx)
+/**
+  * @brief Enable interrupt on Vddio2 Monitor Exti Line 31.
+  * @retval None.
+  */
+#define __HAL_PWR_VDDIO2_EXTI_ENABLE_IT()             (EXTI->IMR |= (PWR_EXTI_LINE_VDDIO2))
+
+/**
+  * @brief Disable interrupt on Vddio2 Monitor Exti Line 31.
+  * @retval None.
+  */
+#define __HAL_PWR_VDDIO2_EXTI_DISABLE_IT()            (EXTI->IMR &= ~(PWR_EXTI_LINE_VDDIO2))
+
+/**
+  * @brief  Vddio2 Monitor EXTI line configuration: clear falling edge and rising edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_VDDIO2_EXTI_DISABLE_FALLING_EDGE()                 \
+                        do{                                          \
+                            EXTI->FTSR &= ~(PWR_EXTI_LINE_VDDIO2);   \
+                            EXTI->RTSR &= ~(PWR_EXTI_LINE_VDDIO2);   \
+                          } while(0)
+                    
+/**
+  * @brief  Vddio2 Monitor EXTI line configuration: set falling edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_VDDIO2_EXTI_ENABLE_FALLING_EDGE()  EXTI->FTSR |= (PWR_EXTI_LINE_VDDIO2)
+
+/**
+  * @brief Check whether the specified VDDIO2 monitor EXTI interrupt flag is set or not.
+  * @retval EXTI VDDIO2 Monitor Line Status.
+  */
+#define __HAL_PWR_VDDIO2_EXTI_GET_FLAG()              (EXTI->PR & (PWR_EXTI_LINE_VDDIO2))
+
+/**
+  * @brief Clear the VDDIO2 Monitor EXTI flag.
+  * @retval None.
+  */
+#define __HAL_PWR_VDDIO2_EXTI_CLEAR_FLAG()            (EXTI->PR = (PWR_EXTI_LINE_VDDIO2))
+
+/**
+  * @brief Generate a Software interrupt on selected EXTI line.
+  * @retval None.
+  */
+#define __HAL_PWR_VDDIO2_EXTI_GENERATE_SWIT()         (EXTI->SWIER |= (PWR_EXTI_LINE_VDDIO2))
+
+
+#endif /* defined (STM32F042x6) || defined (STM32F048xx) ||\
+          defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+          defined (STM32F091xC) || defined (STM32F098xx) */
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup PWREx_Exported_Functions PWREx Exported Functions
+ *  @{
+ */
+
+/** @addtogroup PWREx_Exported_Functions_Group1
+  * @{
+  */
+/* I/O operation functions  ***************************************************/
+#if defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || \
+    defined (STM32F091xC)
+void HAL_PWR_PVD_IRQHandler(void);
+void HAL_PWR_PVDCallback(void);
+#endif /* defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || */
+       /* defined (STM32F071xB) || defined (STM32F072xB) || */
+       /* defined (STM32F091xC) */
+
+#if defined (STM32F042x6) || defined (STM32F048xx) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+    defined (STM32F091xC) || defined (STM32F098xx)
+void HAL_PWREx_Vddio2Monitor_IRQHandler(void);
+void HAL_PWREx_Vddio2MonitorCallback(void);
+#endif /* defined (STM32F042x6) || defined (STM32F048xx) || \
+          defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+          defined (STM32F091xC) || defined (STM32F098xx) */
+
+/* Peripheral Control functions  **********************************************/
+#if defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || \
+    defined (STM32F091xC)
+void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD);
+void HAL_PWR_EnablePVD(void);
+void HAL_PWR_DisablePVD(void);
+#endif /* defined (STM32F031x6) || defined (STM32F042x6) || defined (STM32F051x8) || */
+       /* defined (STM32F071xB) || defined (STM32F072xB) || */
+       /* defined (STM32F091xC) */
+       
+#if defined (STM32F042x6) || defined (STM32F048xx) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+    defined (STM32F091xC) || defined (STM32F098xx)
+void HAL_PWREx_EnableVddio2Monitor(void);
+void HAL_PWREx_DisableVddio2Monitor(void);
+#endif /* defined (STM32F042x6) || defined (STM32F048xx) || \
+          defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+          defined (STM32F091xC) || defined (STM32F098xx) */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_PWR_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

LED/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_hal_tim_ex.h

@@ -0,0 +1,268 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_tim_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of TIM HAL Extended module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F0xx_HAL_TIM_EX_H
+#define STM32F0xx_HAL_TIM_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup TIMEx
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Types TIM Extended Exported Types
+  * @{
+  */
+
+/**
+  * @brief  TIM Hall sensor Configuration Structure definition
+  */
+
+typedef struct
+{
+  uint32_t IC1Polarity;         /*!< Specifies the active edge of the input signal.
+                                     This parameter can be a value of @ref TIM_Input_Capture_Polarity */
+
+  uint32_t IC1Prescaler;        /*!< Specifies the Input Capture Prescaler.
+                                     This parameter can be a value of @ref TIM_Input_Capture_Prescaler */
+
+  uint32_t IC1Filter;           /*!< Specifies the input capture filter.
+                                     This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */
+
+  uint32_t Commutation_Delay;   /*!< Specifies the pulse value to be loaded into the Capture Compare Register.
+                                     This parameter can be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */
+} TIM_HallSensor_InitTypeDef;
+/**
+  * @}
+  */
+/* End of exported types -----------------------------------------------------*/
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Constants TIM Extended Exported Constants
+  * @{
+  */
+
+/** @defgroup TIMEx_Remap TIM Extended Remapping
+  * @{
+  */
+#define TIM_TIM14_GPIO                         (0x00000000U) /*!< TIM14 TI1 is connected to GPIO */
+#define TIM_TIM14_RTC                          (0x00000001U) /*!< TIM14 TI1 is connected to RTC_clock */
+#define TIM_TIM14_HSE                          (0x00000002U) /*!< TIM14 TI1 is connected to HSE/32U */
+#define TIM_TIM14_MCO                          (0x00000003U) /*!< TIM14 TI1 is connected to MCO */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* End of exported constants -------------------------------------------------*/
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Macros TIM Extended Exported Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+/* End of exported macro -----------------------------------------------------*/
+
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup TIMEx_Private_Macros TIM Extended Private Macros
+  * @{
+  */
+#define IS_TIM_REMAP(__INSTANCE__, __REMAP__)                                        \
+  (((__INSTANCE__) == TIM14)  && (((__REMAP__) & 0xFFFFFFFCU) == 0x00000000U))
+
+/**
+  * @}
+  */
+/* End of private macro ------------------------------------------------------*/
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup TIMEx_Exported_Functions TIM Extended Exported Functions
+  * @{
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group1 Extended Timer Hall Sensor functions
+  *  @brief    Timer Hall Sensor functions
+  * @{
+  */
+/*  Timer Hall Sensor functions  **********************************************/
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, TIM_HallSensor_InitTypeDef *sConfig);
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef *htim);
+
+void HAL_TIMEx_HallSensor_MspInit(TIM_HandleTypeDef *htim);
+void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef *htim);
+
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef *htim);
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef *htim);
+/* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef *htim);
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef *htim);
+/* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length);
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef *htim);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group2 Extended Timer Complementary Output Compare functions
+  *  @brief   Timer Complementary Output Compare functions
+  * @{
+  */
+/*  Timer Complementary Output Compare functions  *****************************/
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef *htim, uint32_t Channel);
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel);
+
+/* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
+
+/* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length);
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group3 Extended Timer Complementary PWM functions
+  *  @brief    Timer Complementary PWM functions
+  * @{
+  */
+/*  Timer Complementary PWM functions  ****************************************/
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef *htim, uint32_t Channel);
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel);
+
+/* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
+/* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length);
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group4 Extended Timer Complementary One Pulse functions
+  *  @brief    Timer Complementary One Pulse functions
+  * @{
+  */
+/*  Timer Complementary One Pulse functions  **********************************/
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
+
+/* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group5 Extended Peripheral Control functions
+  *  @brief    Peripheral Control functions
+  * @{
+  */
+/* Extended Control functions  ************************************************/
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent(TIM_HandleTypeDef *htim, uint32_t  InputTrigger,
+                                              uint32_t  CommutationSource);
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_IT(TIM_HandleTypeDef *htim, uint32_t  InputTrigger,
+                                                 uint32_t  CommutationSource);
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_DMA(TIM_HandleTypeDef *htim, uint32_t  InputTrigger,
+                                                  uint32_t  CommutationSource);
+HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim,
+                                                        TIM_MasterConfigTypeDef *sMasterConfig);
+HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim,
+                                                TIM_BreakDeadTimeConfigTypeDef *sBreakDeadTimeConfig);
+HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef *htim, uint32_t Remap);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group6 Extended Callbacks functions
+  * @brief    Extended Callbacks functions
+  * @{
+  */
+/* Extended Callback **********************************************************/
+void HAL_TIMEx_CommutCallback(TIM_HandleTypeDef *htim);
+void HAL_TIMEx_CommutHalfCpltCallback(TIM_HandleTypeDef *htim);
+void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef *htim);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group7 Extended Peripheral State functions
+  * @brief    Extended Peripheral State functions
+  * @{
+  */
+/* Extended Peripheral State functions  ***************************************/
+HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef *htim);
+HAL_TIM_ChannelStateTypeDef HAL_TIMEx_GetChannelNState(TIM_HandleTypeDef *htim,  uint32_t ChannelN);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* End of exported functions -------------------------------------------------*/
+
+/* Private functions----------------------------------------------------------*/
+/** @addtogroup TIMEx_Private_Functions TIMEx Private Functions
+  * @{
+  */
+void TIMEx_DMACommutationCplt(DMA_HandleTypeDef *hdma);
+void TIMEx_DMACommutationHalfCplt(DMA_HandleTypeDef *hdma);
+/**
+  * @}
+  */
+/* End of private functions --------------------------------------------------*/
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* STM32F0xx_HAL_TIM_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal.c

@@ -0,0 +1,514 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal.c
+  * @author  MCD Application Team
+  * @brief   HAL module driver.
+  *          This is the common part of the HAL initialization
+  *
+  @verbatim
+  ==============================================================================
+                     ##### How to use this driver #####
+  ==============================================================================
+    [..]
+    The common HAL driver contains a set of generic and common APIs that can be
+    used by the PPP peripheral drivers and the user to start using the HAL. 
+    [..]
+    The HAL contains two APIs categories:
+         (+) HAL Initialization and de-initialization functions
+         (+) HAL Control functions
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup HAL HAL
+  * @brief HAL module driver.
+  * @{
+  */
+
+#ifdef HAL_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @defgroup HAL_Private_Constants HAL Private Constants
+  * @{
+  */
+/** 
+  * @brief STM32F0xx HAL Driver version number V1.7.5
+  */
+#define __STM32F0xx_HAL_VERSION_MAIN   (0x01) /*!< [31:24] main version */
+#define __STM32F0xx_HAL_VERSION_SUB1   (0x07) /*!< [23:16] sub1 version */
+#define __STM32F0xx_HAL_VERSION_SUB2   (0x05) /*!< [15:8]  sub2 version */
+#define __STM32F0xx_HAL_VERSION_RC     (0x00) /*!< [7:0]  release candidate */ 
+#define __STM32F0xx_HAL_VERSION         ((__STM32F0xx_HAL_VERSION_MAIN << 24U)\
+                                        |(__STM32F0xx_HAL_VERSION_SUB1 << 16U)\
+                                        |(__STM32F0xx_HAL_VERSION_SUB2 << 8U )\
+                                        |(__STM32F0xx_HAL_VERSION_RC))
+
+#define IDCODE_DEVID_MASK    (0x00000FFFU)
+/**
+  * @}
+  */
+
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup HAL_Private_Macros HAL Private Macros
+  * @{
+  */
+/**
+  * @}
+  */
+
+/* Exported variables ---------------------------------------------------------*/
+/** @defgroup HAL_Private_Variables HAL Exported Variables
+  * @{
+  */
+__IO uint32_t uwTick;
+uint32_t uwTickPrio   = (1UL << __NVIC_PRIO_BITS); /* Invalid PRIO */
+HAL_TickFreqTypeDef uwTickFreq = HAL_TICK_FREQ_DEFAULT;  /* 1KHz */
+/**
+  * @}
+  */
+/* Private function prototypes -----------------------------------------------*/
+/* Exported functions ---------------------------------------------------------*/
+
+/** @defgroup HAL_Exported_Functions HAL Exported Functions
+  * @{
+  */
+
+/** @defgroup HAL_Exported_Functions_Group1 Initialization and de-initialization Functions 
+  * @brief    Initialization and de-initialization functions
+  *
+@verbatim
+ ===============================================================================
+              ##### Initialization and de-initialization functions #####
+ ===============================================================================
+   [..]  This section provides functions allowing to:
+      (+) Initializes the Flash interface, the NVIC allocation and initial clock 
+          configuration. It initializes the systick also when timeout is needed
+          and the backup domain when enabled.
+      (+) de-Initializes common part of the HAL.
+      (+) Configure The time base source to have 1ms time base with a dedicated
+          Tick interrupt priority.
+        (++) SysTick timer is used by default as source of time base, but user
+             can eventually implement his proper time base source (a general purpose 
+             timer for example or other time source), keeping in mind that Time base 
+             duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
+             handled in milliseconds basis.
+        (++) Time base configuration function (HAL_InitTick ()) is called automatically 
+             at the beginning of the program after reset by HAL_Init() or at any time 
+             when clock is configured, by HAL_RCC_ClockConfig(). 
+        (++) Source of time base is configured  to generate interrupts at regular 
+             time intervals. Care must be taken if HAL_Delay() is called from a 
+             peripheral ISR process, the Tick interrupt line must have higher priority 
+            (numerically lower) than the peripheral interrupt. Otherwise the caller 
+            ISR process will be blocked. 
+       (++) functions affecting time base configurations are declared as __Weak  
+             to make  override possible  in case of other  implementations in user file.
+ 
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  This function configures the Flash prefetch,
+  *        Configures time base source, NVIC and Low level hardware
+  * @note This function is called at the beginning of program after reset and before 
+  *       the clock configuration
+  * @note The time base configuration is based on HSI clock when exiting from Reset.
+  *       Once done, time base tick start incrementing.
+  *       In the default implementation,Systick is used as source of time base.
+  *       The tick variable is incremented each 1ms in its ISR.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_Init(void)
+{
+  /* Configure Flash prefetch */ 
+#if (PREFETCH_ENABLE != 0)
+  __HAL_FLASH_PREFETCH_BUFFER_ENABLE();
+#endif /* PREFETCH_ENABLE */
+
+  /* Use systick as time base source and configure 1ms tick (default clock after Reset is HSI) */
+
+  HAL_InitTick(TICK_INT_PRIORITY);
+
+  /* Init the low level hardware */
+  HAL_MspInit();
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief This function de-Initialize common part of the HAL and stops the SysTick
+  *        of time base.
+  * @note This function is optional.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DeInit(void)
+{
+  /* Reset of all peripherals */
+  __HAL_RCC_APB1_FORCE_RESET();
+  __HAL_RCC_APB1_RELEASE_RESET();
+
+  __HAL_RCC_APB2_FORCE_RESET();
+  __HAL_RCC_APB2_RELEASE_RESET();
+
+  __HAL_RCC_AHB_FORCE_RESET();
+  __HAL_RCC_AHB_RELEASE_RESET();
+
+  /* De-Init the low level hardware */
+  HAL_MspDeInit();
+    
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Initialize the MSP.
+  * @retval None
+  */
+__weak void HAL_MspInit(void)
+{
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_MspInit could be implemented in the user file
+   */
+}
+
+/**
+  * @brief  DeInitializes the MSP.
+  * @retval None
+  */
+__weak void HAL_MspDeInit(void)
+{
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_MspDeInit could be implemented in the user file
+   */
+}
+
+/**
+  * @brief This function configures the source of the time base. 
+  *        The time source is configured  to have 1ms time base with a dedicated 
+  *        Tick interrupt priority.
+  * @note This function is called  automatically at the beginning of program after
+  *       reset by HAL_Init() or at any time when clock is reconfigured  by HAL_RCC_ClockConfig(). 
+  * @note In the default implementation, SysTick timer is the source of time base. 
+  *       It is used to generate interrupts at regular time intervals. 
+  *       Care must be taken if HAL_Delay() is called from a peripheral ISR process, 
+  *       The SysTick interrupt must have higher priority (numerically lower) 
+  *       than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
+  *       The function is declared as __Weak  to be overwritten  in case of other
+  *       implementation  in user file.
+  * @param TickPriority Tick interrupt priority.
+  * @retval HAL status
+  */
+__weak HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority)
+{
+  /*Configure the SysTick to have interrupt in 1ms time basis*/
+  if (HAL_SYSTICK_Config(SystemCoreClock / (1000U / uwTickFreq)) > 0U)
+  {
+    return HAL_ERROR;
+  }
+
+  /* Configure the SysTick IRQ priority */
+  if (TickPriority < (1UL << __NVIC_PRIO_BITS))
+  {
+    HAL_NVIC_SetPriority(SysTick_IRQn, TickPriority, 0U);
+    uwTickPrio = TickPriority;
+  }
+  else
+  {
+    return HAL_ERROR;
+  }
+
+   /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_Exported_Functions_Group2 HAL Control functions 
+  * @brief    HAL Control functions
+  *
+@verbatim
+ ===============================================================================
+                      ##### HAL Control functions #####
+ ===============================================================================
+    [..]  This section provides functions allowing to:
+      (+) Provide a tick value in millisecond
+      (+) Provide a blocking delay in millisecond
+      (+) Suspend the time base source interrupt
+      (+) Resume the time base source interrupt
+      (+) Get the HAL API driver version
+      (+) Get the device identifier
+      (+) Get the device revision identifier
+      (+) Enable/Disable Debug module during Sleep mode
+      (+) Enable/Disable Debug module during STOP mode
+      (+) Enable/Disable Debug module during STANDBY mode
+      
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief This function is called to increment  a global variable "uwTick"
+  *        used as application time base.
+  * @note In the default implementation, this variable is incremented each 1ms
+  *       in SysTick ISR.
+  * @note This function is declared as __weak to be overwritten in case of other 
+  *       implementations in user file.
+  * @retval None
+  */
+__weak void HAL_IncTick(void)
+{
+  uwTick += uwTickFreq;
+}
+
+/**
+  * @brief  Provides a tick value in millisecond.
+  * @note   This function is declared as __weak  to be overwritten  in case of other 
+  *       implementations in user file.
+  * @retval tick value
+  */
+__weak uint32_t HAL_GetTick(void)
+{
+  return uwTick;
+}
+
+/**
+  * @brief This function returns a tick priority.
+  * @retval tick priority
+  */
+uint32_t HAL_GetTickPrio(void)
+{
+  return uwTickPrio;
+}
+
+/**
+  * @brief Set new tick Freq.
+  * @retval status
+  */
+HAL_StatusTypeDef HAL_SetTickFreq(HAL_TickFreqTypeDef Freq)
+{
+  HAL_StatusTypeDef status  = HAL_OK;
+  HAL_TickFreqTypeDef prevTickFreq;
+
+  assert_param(IS_TICKFREQ(Freq));
+
+  if (uwTickFreq != Freq)
+  {
+    /* Back up uwTickFreq frequency */
+    prevTickFreq = uwTickFreq;
+
+    /* Update uwTickFreq global variable used by HAL_InitTick() */
+    uwTickFreq = Freq;
+
+    /* Apply the new tick Freq */
+    status = HAL_InitTick(uwTickPrio);
+
+    if (status != HAL_OK)
+    {
+      /* Restore previous tick frequency */
+      uwTickFreq = prevTickFreq;
+    }
+  }
+
+  return status;
+}
+
+/**
+  * @brief return tick frequency.
+  * @retval tick period in Hz
+  */
+HAL_TickFreqTypeDef HAL_GetTickFreq(void)
+{
+  return uwTickFreq;
+}
+
+/**
+  * @brief This function provides accurate delay (in milliseconds) based 
+  *        on variable incremented.
+  * @note In the default implementation , SysTick timer is the source of time base.
+  *       It is used to generate interrupts at regular time intervals where uwTick
+  *       is incremented.
+  * @note ThiS function is declared as __weak to be overwritten in case of other
+  *       implementations in user file.
+  * @param Delay specifies the delay time length, in milliseconds.
+  * @retval None
+  */
+__weak void HAL_Delay(uint32_t Delay)
+{
+  uint32_t tickstart = HAL_GetTick();
+  uint32_t wait = Delay;
+  
+  /* Add a freq to guarantee minimum wait */
+  if (wait < HAL_MAX_DELAY)
+  {
+    wait += (uint32_t)(uwTickFreq);
+  }
+  
+  while((HAL_GetTick() - tickstart) < wait)
+  {
+  }
+}
+
+/**
+  * @brief Suspend Tick increment.
+  * @note In the default implementation , SysTick timer is the source of time base. It is
+  *       used to generate interrupts at regular time intervals. Once HAL_SuspendTick()
+  *       is called, the the SysTick interrupt will be disabled and so Tick increment 
+  *       is suspended.
+  * @note This function is declared as __weak to be overwritten in case of other
+  *       implementations in user file.
+  * @retval None
+  */
+__weak void HAL_SuspendTick(void)
+
+{
+  /* Disable SysTick Interrupt */
+  CLEAR_BIT(SysTick->CTRL,SysTick_CTRL_TICKINT_Msk);
+}
+
+/**
+  * @brief Resume Tick increment.
+  * @note In the default implementation , SysTick timer is the source of time base. It is
+  *       used to generate interrupts at regular time intervals. Once HAL_ResumeTick()
+  *       is called, the the SysTick interrupt will be enabled and so Tick increment 
+  *       is resumed.
+  * @note This function is declared as __weak  to be overwritten  in case of other
+  *       implementations in user file.
+  * @retval None
+  */
+__weak void HAL_ResumeTick(void)
+{
+  /* Enable SysTick Interrupt */
+  SET_BIT(SysTick->CTRL,SysTick_CTRL_TICKINT_Msk);
+}
+
+/**
+  * @brief  This method returns the HAL revision
+  * @retval version 0xXYZR (8bits for each decimal, R for RC)
+  */
+uint32_t HAL_GetHalVersion(void)
+{
+ return __STM32F0xx_HAL_VERSION;
+}
+
+/**
+  * @brief  Returns the device revision identifier.
+  * @retval Device revision identifier
+  */
+uint32_t HAL_GetREVID(void)
+{
+   return((DBGMCU->IDCODE) >> 16U);
+}
+
+/**
+  * @brief  Returns the device identifier.
+  * @retval Device identifier
+  */
+uint32_t HAL_GetDEVID(void)
+{
+   return((DBGMCU->IDCODE) & IDCODE_DEVID_MASK);
+}
+
+/**
+  * @brief  Returns first word of the unique device identifier (UID based on 96 bits)
+  * @retval Device identifier
+  */
+uint32_t HAL_GetUIDw0(void)
+{
+   return(READ_REG(*((uint32_t *)UID_BASE)));
+}
+
+/**
+  * @brief  Returns second word of the unique device identifier (UID based on 96 bits)
+  * @retval Device identifier
+  */
+uint32_t HAL_GetUIDw1(void)
+{
+   return(READ_REG(*((uint32_t *)(UID_BASE + 4U))));
+}
+
+/**
+  * @brief  Returns third word of the unique device identifier (UID based on 96 bits)
+  * @retval Device identifier
+  */
+uint32_t HAL_GetUIDw2(void)
+{
+   return(READ_REG(*((uint32_t *)(UID_BASE + 8U))));
+}
+
+/**
+  * @brief  Enable the Debug Module during STOP mode
+  * @retval None
+  */
+void HAL_DBGMCU_EnableDBGStopMode(void)
+{
+  SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STOP);
+}
+
+/**
+  * @brief  Disable the Debug Module during STOP mode
+  * @retval None
+  */
+void HAL_DBGMCU_DisableDBGStopMode(void)
+{
+  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STOP);
+}
+
+/**
+  * @brief  Enable the Debug Module during STANDBY mode
+  * @retval None
+  */
+void HAL_DBGMCU_EnableDBGStandbyMode(void)
+{
+  SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY);
+}
+
+/**
+  * @brief  Disable the Debug Module during STANDBY mode
+  * @retval None
+  */
+void HAL_DBGMCU_DisableDBGStandbyMode(void)
+{
+  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY);
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_cortex.c

@@ -0,0 +1,341 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_cortex.c
+  * @author  MCD Application Team
+  * @brief   CORTEX HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the CORTEX:
+  *           + Initialization and de-initialization functions
+  *           + Peripheral Control functions 
+  *
+  *  @verbatim
+  ==============================================================================
+                        ##### How to use this driver #####
+  ==============================================================================
+
+    [..]  
+    *** How to configure Interrupts using CORTEX HAL driver ***
+    ===========================================================
+    [..]
+    This section provides functions allowing to configure the NVIC interrupts (IRQ).
+    The Cortex-M0 exceptions are managed by CMSIS functions.
+      (#) Enable and Configure the priority of the selected IRQ Channels. 
+             The priority can be 0..3. 
+
+        -@- Lower priority values gives higher priority.
+        -@- Priority Order:
+            (#@) Lowest priority.
+            (#@) Lowest hardware priority (IRQn position).  
+
+      (#)  Configure the priority of the selected IRQ Channels using HAL_NVIC_SetPriority()
+
+      (#)  Enable the selected IRQ Channels using HAL_NVIC_EnableIRQ()
+      
+      -@-  Negative value of IRQn_Type are not allowed.
+
+
+    [..]
+    *** How to configure Systick using CORTEX HAL driver ***
+    ========================================================
+    [..]
+    Setup SysTick Timer for time base. 
+           
+   (+) The HAL_SYSTICK_Config()function calls the SysTick_Config() function which
+       is a CMSIS function that:
+        (++) Configures the SysTick Reload register with value passed as function parameter.
+        (++) Configures the SysTick IRQ priority to the lowest value (0x03).
+        (++) Resets the SysTick Counter register.
+        (++) Configures the SysTick Counter clock source to be Core Clock Source (HCLK).
+        (++) Enables the SysTick Interrupt.
+        (++) Starts the SysTick Counter.
+    
+   (+) You can change the SysTick Clock source to be HCLK_Div8 by calling the macro
+       HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK_DIV8) just after the
+       HAL_SYSTICK_Config() function call. The HAL_SYSTICK_CLKSourceConfig() macro is defined
+       inside the stm32f0xx_hal_cortex.h file.
+
+   (+) You can change the SysTick IRQ priority by calling the
+       HAL_NVIC_SetPriority(SysTick_IRQn,...) function just after the HAL_SYSTICK_Config() function 
+       call. The HAL_NVIC_SetPriority() call the NVIC_SetPriority() function which is a CMSIS function.
+
+   (+) To adjust the SysTick time base, use the following formula:
+
+       Reload Value = SysTick Counter Clock (Hz) x  Desired Time base (s)
+       (++) Reload Value is the parameter to be passed for HAL_SYSTICK_Config() function
+       (++) Reload Value should not exceed 0xFFFFFF
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup CORTEX CORTEX
+  * @brief CORTEX CORTEX HAL module driver
+  * @{
+  */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Exported functions ---------------------------------------------------------*/
+
+/** @defgroup CORTEX_Exported_Functions CORTEX Exported Functions
+  * @{
+  */
+
+
+/** @defgroup CORTEX_Exported_Functions_Group1 Initialization and de-initialization functions 
+ *  @brief    Initialization and Configuration functions
+ *
+@verbatim
+  ==============================================================================
+              ##### Initialization and de-initialization functions #####
+  ==============================================================================
+    [..]
+      This section provides the CORTEX HAL driver functions allowing to configure Interrupts
+      Systick functionalities 
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Sets the priority of an interrupt.
+  * @param  IRQn External interrupt number .
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to stm32f0xx.h file)
+  * @param  PreemptPriority The preemption priority for the IRQn channel.
+  *         This parameter can be a value between 0 and 3.
+  *         A lower priority value indicates a higher priority
+  * @param  SubPriority the subpriority level for the IRQ channel.
+  *         with stm32f0xx devices, this parameter is a dummy value and it is ignored, because 
+  *         no subpriority supported in Cortex M0 based products.   
+  * @retval None
+  */
+void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority)
+{ 
+  /* Check the parameters */
+  assert_param(IS_NVIC_PREEMPTION_PRIORITY(PreemptPriority));
+  NVIC_SetPriority(IRQn,PreemptPriority);
+}
+
+/**
+  * @brief  Enables a device specific interrupt in the NVIC interrupt controller.
+  * @note   To configure interrupts priority correctly, the NVIC_PriorityGroupConfig()
+  *         function should be called before. 
+  * @param  IRQn External interrupt number.
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h))
+  * @retval None
+  */
+void HAL_NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
+  
+  /* Enable interrupt */
+  NVIC_EnableIRQ(IRQn);
+}
+
+/**
+  * @brief  Disables a device specific interrupt in the NVIC interrupt controller.
+  * @param  IRQn External interrupt number.
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h))
+  * @retval None
+  */
+void HAL_NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
+  
+  /* Disable interrupt */
+  NVIC_DisableIRQ(IRQn);
+}
+
+/**
+  * @brief  Initiates a system reset request to reset the MCU.
+  * @retval None
+  */
+void HAL_NVIC_SystemReset(void)
+{
+  /* System Reset */
+  NVIC_SystemReset();
+}
+
+/**
+  * @brief  Initializes the System Timer and its interrupt, and starts the System Tick Timer.
+  *         Counter is in free running mode to generate periodic interrupts.
+  * @param  TicksNumb Specifies the ticks Number of ticks between two interrupts.
+  * @retval status:  - 0  Function succeeded.
+  *                  - 1  Function failed.
+  */
+uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb)
+{
+   return SysTick_Config(TicksNumb);
+}
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_Exported_Functions_Group2 Peripheral Control functions 
+ *  @brief   Cortex control functions
+ *
+@verbatim
+  ==============================================================================
+                      ##### Peripheral Control functions #####
+  ==============================================================================
+    [..]
+      This subsection provides a set of functions allowing to control the CORTEX
+      (NVIC, SYSTICK) functionalities.
+
+
+@endverbatim
+  * @{
+  */
+
+
+/**
+  * @brief  Gets the priority of an interrupt.
+  * @param  IRQn External interrupt number.
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h))
+  * @retval None
+  */
+uint32_t HAL_NVIC_GetPriority(IRQn_Type IRQn)
+{
+  /* Get priority for Cortex-M system or device specific interrupts */
+  return NVIC_GetPriority(IRQn);
+}
+
+/**
+  * @brief  Sets Pending bit of an external interrupt.
+  * @param  IRQn External interrupt number
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h))
+  * @retval None
+  */
+void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
+  
+  /* Set interrupt pending */
+  NVIC_SetPendingIRQ(IRQn);
+}
+
+/**
+  * @brief  Gets Pending Interrupt (reads the pending register in the NVIC
+  *         and returns the pending bit for the specified interrupt).
+  * @param  IRQn External interrupt number.
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h))
+  * @retval status: - 0  Interrupt status is not pending.
+  *                 - 1  Interrupt status is pending.
+  */
+uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
+  
+  /* Return 1 if pending else 0 */
+  return NVIC_GetPendingIRQ(IRQn);
+}
+
+/**
+  * @brief  Clears the pending bit of an external interrupt.
+  * @param  IRQn External interrupt number.
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h))
+  * @retval None
+  */
+void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
+  
+  /* Clear pending interrupt */
+  NVIC_ClearPendingIRQ(IRQn);
+}
+
+/**
+  * @brief  Configures the SysTick clock source.
+  * @param  CLKSource specifies the SysTick clock source.
+  *         This parameter can be one of the following values:
+  *             @arg SYSTICK_CLKSOURCE_HCLK_DIV8: AHB clock divided by 8 selected as SysTick clock source.
+  *             @arg SYSTICK_CLKSOURCE_HCLK: AHB clock selected as SysTick clock source.
+  * @retval None
+  */
+void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource)
+{
+  /* Check the parameters */
+  assert_param(IS_SYSTICK_CLK_SOURCE(CLKSource));
+  if (CLKSource == SYSTICK_CLKSOURCE_HCLK)
+  {
+    SysTick->CTRL |= SYSTICK_CLKSOURCE_HCLK;
+  }
+  else
+  {
+    SysTick->CTRL &= ~SYSTICK_CLKSOURCE_HCLK;
+  }
+}
+
+/**
+  * @brief  This function handles SYSTICK interrupt request.
+  * @retval None
+  */
+void HAL_SYSTICK_IRQHandler(void)
+{
+  HAL_SYSTICK_Callback();
+}
+
+/**
+  * @brief  SYSTICK callback.
+  * @retval None
+  */
+__weak void HAL_SYSTICK_Callback(void)
+{
+  /* NOTE : This function Should not be modified, when the callback is needed,
+            the HAL_SYSTICK_Callback could be implemented in the user file
+   */
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_dma.c

@@ -0,0 +1,901 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_dma.c
+  * @author  MCD Application Team
+  * @brief   DMA HAL module driver.
+  *    
+  *         This file provides firmware functions to manage the following 
+  *         functionalities of the Direct Memory Access (DMA) peripheral:
+  *           + Initialization and de-initialization functions
+  *           + IO operation functions
+  *           + Peripheral State and errors functions
+  @verbatim     
+  ==============================================================================      
+                        ##### How to use this driver #####
+  ============================================================================== 
+  [..]
+   (#) Enable and configure the peripheral to be connected to the DMA Channel
+       (except for internal SRAM / FLASH memories: no initialization is 
+       necessary). Please refer to Reference manual for connection between peripherals
+       and DMA requests .
+
+   (#) For a given Channel, program the required configuration through the following parameters:   
+       Transfer Direction, Source and Destination data formats, 
+       Circular or Normal mode, Channel Priority level, Source and Destination Increment mode, 
+       using HAL_DMA_Init() function.
+
+   (#) Use HAL_DMA_GetState() function to return the DMA state and HAL_DMA_GetError() in case of error 
+       detection.
+                    
+   (#) Use HAL_DMA_Abort() function to abort the current transfer
+                   
+     -@-   In Memory-to-Memory transfer mode, Circular mode is not allowed.
+     *** Polling mode IO operation ***
+     =================================   
+    [..] 
+      (+) Use HAL_DMA_Start() to start DMA transfer after the configuration of Source 
+          address and destination address and the Length of data to be transferred
+      (+) Use HAL_DMA_PollForTransfer() to poll for the end of current transfer, in this  
+          case a fixed Timeout can be configured by User depending from his application.
+
+     *** Interrupt mode IO operation ***    
+     =================================== 
+    [..]
+      (+) Configure the DMA interrupt priority using HAL_NVIC_SetPriority()
+      (+) Enable the DMA IRQ handler using HAL_NVIC_EnableIRQ() 
+      (+) Use HAL_DMA_Start_IT() to start DMA transfer after the configuration of  
+          Source address and destination address and the Length of data to be transferred. 
+          In this case the DMA interrupt is configured 
+      (+) Use HAL_DMA_Channel_IRQHandler() called under DMA_IRQHandler() Interrupt subroutine
+      (+) At the end of data transfer HAL_DMA_IRQHandler() function is executed and user can 
+          add his own function by customization of function pointer XferCpltCallback and 
+          XferErrorCallback (i.e a member of DMA handle structure). 
+
+     *** DMA HAL driver macros list ***
+     ============================================= 
+     [..]
+       Below the list of most used macros in DMA HAL driver.
+
+     [..] 
+      (@) You can refer to the DMA HAL driver header file for more useful macros  
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+
+/** @defgroup DMA DMA
+  * @brief DMA HAL module driver
+  * @{
+  */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/** @defgroup DMA_Private_Functions DMA Private Functions
+  * @{
+  */
+static void DMA_SetConfig(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
+static void DMA_CalcBaseAndBitshift(DMA_HandleTypeDef *hdma);
+/**
+  * @}
+  */
+
+/* Exported functions ---------------------------------------------------------*/
+
+/** @defgroup DMA_Exported_Functions DMA Exported Functions
+  * @{
+  */
+
+/** @defgroup DMA_Exported_Functions_Group1 Initialization and de-initialization functions
+ *  @brief   Initialization and de-initialization functions 
+ *
+@verbatim   
+ ===============================================================================
+             ##### Initialization and de-initialization functions  #####
+ ===============================================================================  
+    [..]
+    This section provides functions allowing to initialize the DMA Channel source
+    and destination addresses, incrementation and data sizes, transfer direction, 
+    circular/normal mode selection, memory-to-memory mode selection and Channel priority value.
+    [..]
+    The HAL_DMA_Init() function follows the DMA configuration procedures as described in
+    reference manual.  
+
+@endverbatim
+  * @{
+  */
+  
+/**
+  * @brief  Initialize the DMA according to the specified
+  *         parameters in the DMA_InitTypeDef and initialize the associated handle.
+  * @param  hdma Pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.  
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_Init(DMA_HandleTypeDef *hdma)
+{ 
+  uint32_t tmp = 0U;
+  
+  /* Check the DMA handle allocation */
+  if(NULL == hdma)
+  {
+    return HAL_ERROR;
+  }
+  
+  /* Check the parameters */
+  assert_param(IS_DMA_ALL_INSTANCE(hdma->Instance));
+  assert_param(IS_DMA_DIRECTION(hdma->Init.Direction));
+  assert_param(IS_DMA_PERIPHERAL_INC_STATE(hdma->Init.PeriphInc));
+  assert_param(IS_DMA_MEMORY_INC_STATE(hdma->Init.MemInc));
+  assert_param(IS_DMA_PERIPHERAL_DATA_SIZE(hdma->Init.PeriphDataAlignment));
+  assert_param(IS_DMA_MEMORY_DATA_SIZE(hdma->Init.MemDataAlignment));
+  assert_param(IS_DMA_MODE(hdma->Init.Mode));
+  assert_param(IS_DMA_PRIORITY(hdma->Init.Priority));
+  
+  /* Change DMA peripheral state */
+  hdma->State = HAL_DMA_STATE_BUSY;
+
+  /* Get the CR register value */
+  tmp = hdma->Instance->CCR;
+  
+  /* Clear PL, MSIZE, PSIZE, MINC, PINC, CIRC, DIR bits */
+  tmp &= ((uint32_t)~(DMA_CCR_PL    | DMA_CCR_MSIZE  | DMA_CCR_PSIZE  | \
+                      DMA_CCR_MINC  | DMA_CCR_PINC   | DMA_CCR_CIRC   | \
+                      DMA_CCR_DIR));
+  
+  /* Prepare the DMA Channel configuration */
+  tmp |=  hdma->Init.Direction        |
+          hdma->Init.PeriphInc           | hdma->Init.MemInc           |
+          hdma->Init.PeriphDataAlignment | hdma->Init.MemDataAlignment |
+          hdma->Init.Mode                | hdma->Init.Priority;
+
+  /* Write to DMA Channel CR register */
+  hdma->Instance->CCR = tmp;  
+  
+  /* Initialize DmaBaseAddress and ChannelIndex parameters used 
+     by HAL_DMA_IRQHandler() and HAL_DMA_PollForTransfer() */
+  DMA_CalcBaseAndBitshift(hdma);
+  
+  /* Initialise the error code */
+  hdma->ErrorCode = HAL_DMA_ERROR_NONE;
+
+  /* Initialize the DMA state*/
+  hdma->State = HAL_DMA_STATE_READY;
+  
+  /* Allocate lock resource and initialize it */
+  hdma->Lock = HAL_UNLOCKED;
+  
+  return HAL_OK;
+}  
+  
+/**
+  * @brief  DeInitialize the DMA peripheral 
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.  
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_DeInit(DMA_HandleTypeDef *hdma)
+{
+  /* Check the DMA handle allocation */
+  if(NULL == hdma)
+  {
+    return HAL_ERROR;
+  }
+  
+  /* Check the parameters */
+  assert_param(IS_DMA_ALL_INSTANCE(hdma->Instance));
+
+  /* Disable the selected DMA Channelx */
+  hdma->Instance->CCR &= ~DMA_CCR_EN;
+
+  /* Reset DMA Channel control register */
+  hdma->Instance->CCR  = 0U;
+
+  /* Reset DMA Channel Number of Data to Transfer register */
+  hdma->Instance->CNDTR = 0U;
+
+  /* Reset DMA Channel peripheral address register */
+  hdma->Instance->CPAR  = 0U;
+  
+  /* Reset DMA Channel memory address register */
+  hdma->Instance->CMAR = 0U;
+
+/* Get DMA Base Address */  
+  DMA_CalcBaseAndBitshift(hdma);
+
+  /* Clear all flags */
+  hdma->DmaBaseAddress->IFCR = DMA_FLAG_GL1 << hdma->ChannelIndex;
+
+  /* Clean callbacks */
+  hdma->XferCpltCallback = NULL;
+  hdma->XferHalfCpltCallback = NULL;
+  hdma->XferErrorCallback = NULL;
+  hdma->XferAbortCallback = NULL;
+
+  /* Reset the error code */
+  hdma->ErrorCode = HAL_DMA_ERROR_NONE;
+
+  /* Reset the DMA state */
+  hdma->State = HAL_DMA_STATE_RESET;
+
+  /* Release Lock */
+  __HAL_UNLOCK(hdma);
+
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Exported_Functions_Group2 Input and Output operation functions 
+ *  @brief   I/O operation functions  
+ *
+@verbatim   
+ ===============================================================================
+                      #####  IO operation functions  #####
+ ===============================================================================  
+    [..]  This section provides functions allowing to:
+      (+) Configure the source, destination address and data length and Start DMA transfer
+      (+) Configure the source, destination address and data length and 
+          Start DMA transfer with interrupt
+      (+) Abort DMA transfer
+      (+) Poll for transfer complete
+      (+) Handle DMA interrupt request  
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Start the DMA Transfer.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *              the configuration information for the specified DMA Channel.  
+  * @param  SrcAddress The source memory Buffer address
+  * @param  DstAddress The destination memory Buffer address
+  * @param  DataLength The length of data to be transferred from source to destination
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_Start(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength)
+{
+	HAL_StatusTypeDef status = HAL_OK;
+
+  /* Check the parameters */
+  assert_param(IS_DMA_BUFFER_SIZE(DataLength));
+  
+  /* Process locked */
+  __HAL_LOCK(hdma);
+  
+  if(HAL_DMA_STATE_READY == hdma->State)
+  {
+  	/* Change DMA peripheral state */  
+  	hdma->State = HAL_DMA_STATE_BUSY;
+  	
+  	hdma->ErrorCode = HAL_DMA_ERROR_NONE;
+  	
+  	/* Disable the peripheral */
+  	hdma->Instance->CCR &= ~DMA_CCR_EN;  
+  	
+  	/* Configure the source, destination address and the data length */
+  	DMA_SetConfig(hdma, SrcAddress, DstAddress, DataLength);
+  	
+  	/* Enable the Peripheral */
+  	hdma->Instance->CCR |= DMA_CCR_EN;  
+  }
+  else
+  {
+  	/* Process Unlocked */
+  	__HAL_UNLOCK(hdma);
+  	
+  	/* Remain BUSY */
+  	status = HAL_BUSY;
+  }  
+
+  return status; 
+} 
+
+/**
+  * @brief  Start the DMA Transfer with interrupt enabled.
+  * @param  hdma       pointer to a DMA_HandleTypeDef structure that contains
+  *                     the configuration information for the specified DMA Channel.  
+  * @param  SrcAddress The source memory Buffer address
+  * @param  DstAddress The destination memory Buffer address
+  * @param  DataLength The length of data to be transferred from source to destination
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength)
+{
+	HAL_StatusTypeDef status = HAL_OK;
+
+  /* Check the parameters */
+  assert_param(IS_DMA_BUFFER_SIZE(DataLength));
+  
+  /* Process locked */
+  __HAL_LOCK(hdma);
+  
+  if(HAL_DMA_STATE_READY == hdma->State)
+  {
+  	/* Change DMA peripheral state */  
+  	hdma->State = HAL_DMA_STATE_BUSY;
+  	
+  	hdma->ErrorCode = HAL_DMA_ERROR_NONE;
+  	
+  	/* Disable the peripheral */
+  	hdma->Instance->CCR &= ~DMA_CCR_EN;
+  	
+  	/* Configure the source, destination address and the data length */  
+  	DMA_SetConfig(hdma, SrcAddress, DstAddress, DataLength);
+  	
+  	/* Enable the transfer complete, & transfer error interrupts */
+  	/* Half transfer interrupt is optional: enable it only if associated callback is available */
+    if(NULL != hdma->XferHalfCpltCallback )
+    {
+      hdma->Instance->CCR |= (DMA_IT_TC | DMA_IT_HT | DMA_IT_TE);
+    }
+  	else
+  	{
+  		hdma->Instance->CCR |= (DMA_IT_TC | DMA_IT_TE);
+  		hdma->Instance->CCR &= ~DMA_IT_HT;
+  	}
+  	
+  	/* Enable the Peripheral */
+  	hdma->Instance->CCR |= DMA_CCR_EN;
+  }
+  else
+  {
+  	/* Process Unlocked */
+    __HAL_UNLOCK(hdma); 
+  
+    /* Remain BUSY */
+    status = HAL_BUSY;
+  }     
+  
+  return status;    
+} 
+
+/**
+  * @brief  Abort the DMA Transfer.
+  * @param  hdma  pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef *hdma)
+{
+  if(hdma->State != HAL_DMA_STATE_BUSY)
+  {
+    /* no transfer ongoing */
+    hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER;
+    
+    /* Process Unlocked */
+    __HAL_UNLOCK(hdma);
+    
+    return HAL_ERROR;
+  }
+  else
+  {
+    /* Disable DMA IT */
+    hdma->Instance->CCR &= ~(DMA_IT_TC | DMA_IT_HT | DMA_IT_TE);
+    
+    /* Disable the channel */
+    hdma->Instance->CCR &= ~DMA_CCR_EN;
+    
+    /* Clear all flags */
+    hdma->DmaBaseAddress->IFCR = (DMA_FLAG_GL1 << hdma->ChannelIndex);
+  }
+  /* Change the DMA state*/
+  hdma->State = HAL_DMA_STATE_READY; 
+  
+  /* Process Unlocked */
+  __HAL_UNLOCK(hdma);
+  
+  return HAL_OK;
+}
+
+/**
+  * @brief  Abort the DMA Transfer in Interrupt mode.
+  * @param  hdma  pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Stream.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_Abort_IT(DMA_HandleTypeDef *hdma)
+{  
+  HAL_StatusTypeDef status = HAL_OK;
+  
+  if(HAL_DMA_STATE_BUSY != hdma->State)
+  {
+    /* no transfer ongoing */
+    hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER;
+        
+    status = HAL_ERROR;
+  }
+  else
+  { 
+  
+    /* Disable DMA IT */
+    hdma->Instance->CCR &= ~(DMA_IT_TC | DMA_IT_HT | DMA_IT_TE);
+    
+    /* Disable the channel */
+    hdma->Instance->CCR &= ~DMA_CCR_EN;
+    
+    /* Clear all flags */
+    hdma->DmaBaseAddress->IFCR = DMA_FLAG_GL1 << hdma->ChannelIndex;
+    
+    /* Change the DMA state */
+    hdma->State = HAL_DMA_STATE_READY;
+    
+    /* Process Unlocked */
+    __HAL_UNLOCK(hdma);
+    
+    /* Call User Abort callback */ 
+    if(hdma->XferAbortCallback != NULL)
+    {
+      hdma->XferAbortCallback(hdma);
+    } 
+  }
+  return status;
+}
+
+/**
+  * @brief  Polling for transfer complete.
+  * @param  hdma    pointer to a DMA_HandleTypeDef structure that contains
+  *                  the configuration information for the specified DMA Channel.
+  * @param  CompleteLevel Specifies the DMA level complete.  
+  * @param  Timeout       Timeout duration.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, uint32_t CompleteLevel, uint32_t Timeout)
+{
+  uint32_t temp;
+  uint32_t tickstart = 0U;
+  
+  if(HAL_DMA_STATE_BUSY != hdma->State)
+  {
+    /* no transfer ongoing */
+    hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER;
+    __HAL_UNLOCK(hdma);
+    return HAL_ERROR;
+  }
+  
+  /* Polling mode not supported in circular mode */
+  if (RESET != (hdma->Instance->CCR & DMA_CCR_CIRC))
+  {
+    hdma->ErrorCode = HAL_DMA_ERROR_NOT_SUPPORTED;
+    return HAL_ERROR;
+  }
+  
+  /* Get the level transfer complete flag */
+  if(HAL_DMA_FULL_TRANSFER == CompleteLevel)
+  {
+    /* Transfer Complete flag */
+    temp = DMA_FLAG_TC1 << hdma->ChannelIndex;
+  }
+  else
+  {
+    /* Half Transfer Complete flag */
+    temp = DMA_FLAG_HT1 << hdma->ChannelIndex;
+  }
+
+  /* Get tick */
+  tickstart = HAL_GetTick();
+
+  while(RESET == (hdma->DmaBaseAddress->ISR & temp))
+  {
+    if(RESET != (hdma->DmaBaseAddress->ISR & (DMA_FLAG_TE1 << hdma->ChannelIndex)))
+    {      
+      /* When a DMA transfer error occurs */
+      /* A hardware clear of its EN bits is performed */
+      /* Clear all flags */
+      hdma->DmaBaseAddress->IFCR = DMA_FLAG_GL1 << hdma->ChannelIndex;
+      
+      /* Update error code */
+      hdma->ErrorCode = HAL_DMA_ERROR_TE;
+
+      /* Change the DMA state */
+      hdma->State= HAL_DMA_STATE_READY;       
+      
+      /* Process Unlocked */
+      __HAL_UNLOCK(hdma);
+      
+      return HAL_ERROR;      
+    }      
+    /* Check for the Timeout */
+    if(Timeout != HAL_MAX_DELAY)
+    {
+      if((Timeout == 0U) || ((HAL_GetTick() - tickstart) > Timeout))
+      {
+        /* Update error code */
+        hdma->ErrorCode = HAL_DMA_ERROR_TIMEOUT;
+        
+        /* Change the DMA state */
+        hdma->State = HAL_DMA_STATE_READY;
+
+        /* Process Unlocked */
+        __HAL_UNLOCK(hdma);
+
+        return HAL_ERROR;
+      }
+    }
+  }
+
+  if(HAL_DMA_FULL_TRANSFER == CompleteLevel)
+  {
+    /* Clear the transfer complete flag */
+    hdma->DmaBaseAddress->IFCR = DMA_FLAG_TC1 << hdma->ChannelIndex;
+
+    /* The selected Channelx EN bit is cleared (DMA is disabled and 
+    all transfers are complete) */
+    hdma->State = HAL_DMA_STATE_READY;
+  }
+  else
+  { 
+    /* Clear the half transfer complete flag */
+    hdma->DmaBaseAddress->IFCR = DMA_FLAG_HT1 << hdma->ChannelIndex;
+  }
+  
+  /* Process unlocked */
+  __HAL_UNLOCK(hdma);  
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Handle DMA interrupt request.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.  
+  * @retval None
+  */
+void HAL_DMA_IRQHandler(DMA_HandleTypeDef *hdma)
+{
+	uint32_t flag_it = hdma->DmaBaseAddress->ISR;
+  uint32_t source_it = hdma->Instance->CCR;
+          
+  /* Half Transfer Complete Interrupt management ******************************/
+  if ((RESET != (flag_it & (DMA_FLAG_HT1 << hdma->ChannelIndex))) && (RESET != (source_it & DMA_IT_HT)))
+  {
+  	/* Disable the half transfer interrupt if the DMA mode is not CIRCULAR */
+  	if((hdma->Instance->CCR & DMA_CCR_CIRC) == 0U)
+  	{
+  		/* Disable the half transfer interrupt */
+  		hdma->Instance->CCR &= ~DMA_IT_HT;
+  	}
+  	
+  	/* Clear the half transfer complete flag */
+  	hdma->DmaBaseAddress->IFCR = DMA_FLAG_HT1 << hdma->ChannelIndex;
+  	
+  	/* DMA peripheral state is not updated in Half Transfer */
+  	/* State is updated only in Transfer Complete case */
+  	
+  	if(hdma->XferHalfCpltCallback != NULL)
+  	{
+  		/* Half transfer callback */
+  		hdma->XferHalfCpltCallback(hdma);
+  	}
+  }
+  
+  /* Transfer Complete Interrupt management ***********************************/
+  else if ((RESET != (flag_it & (DMA_FLAG_TC1 << hdma->ChannelIndex))) && (RESET != (source_it & DMA_IT_TC)))
+  {
+  	if((hdma->Instance->CCR & DMA_CCR_CIRC) == 0U)
+  	{
+  		/* Disable the transfer complete  & transfer error interrupts */
+  		/* if the DMA mode is not CIRCULAR */
+  		hdma->Instance->CCR &= ~(DMA_IT_TC | DMA_IT_TE);
+  		
+  		/* Change the DMA state */
+  		hdma->State = HAL_DMA_STATE_READY;
+  	}
+  	
+  	/* Clear the transfer complete flag */
+  	hdma->DmaBaseAddress->IFCR = DMA_FLAG_TC1 << hdma->ChannelIndex;
+  	
+  	/* Process Unlocked */
+  	__HAL_UNLOCK(hdma);
+  	
+  	if(hdma->XferCpltCallback != NULL)
+  	{
+  		/* Transfer complete callback */
+  		hdma->XferCpltCallback(hdma);
+  	}
+  }
+  
+  /* Transfer Error Interrupt management ***************************************/
+  else if (( RESET != (flag_it & (DMA_FLAG_TE1 << hdma->ChannelIndex))) && (RESET != (source_it & DMA_IT_TE)))
+  {
+  	/* When a DMA transfer error occurs */
+    /* A hardware clear of its EN bits is performed */
+    /* Then, disable all DMA interrupts */
+    hdma->Instance->CCR &= ~(DMA_IT_TC | DMA_IT_HT | DMA_IT_TE);
+    
+    /* Clear all flags */
+    hdma->DmaBaseAddress->IFCR = DMA_FLAG_GL1 << hdma->ChannelIndex;
+    
+    /* Update error code */
+    hdma->ErrorCode = HAL_DMA_ERROR_TE;
+    
+    /* Change the DMA state */
+    hdma->State = HAL_DMA_STATE_READY;    
+    
+    /* Process Unlocked */
+    __HAL_UNLOCK(hdma); 
+    
+    if(hdma->XferErrorCallback != NULL)
+    {
+    	/* Transfer error callback */
+    	hdma->XferErrorCallback(hdma);
+    }
+   }
+}  
+
+/**
+  * @brief  Register callbacks
+  * @param  hdma                 pointer to a DMA_HandleTypeDef structure that contains
+  *                               the configuration information for the specified DMA Stream.
+  * @param  CallbackID           User Callback identifer
+  *                               a HAL_DMA_CallbackIDTypeDef ENUM as parameter.
+  * @param  pCallback            pointer to private callback function which has pointer to 
+  *                               a DMA_HandleTypeDef structure as parameter.
+  * @retval HAL status
+  */                          
+HAL_StatusTypeDef HAL_DMA_RegisterCallback(DMA_HandleTypeDef *hdma, HAL_DMA_CallbackIDTypeDef CallbackID, void (* pCallback)( DMA_HandleTypeDef * _hdma))
+{
+  HAL_StatusTypeDef status = HAL_OK;
+  
+  /* Process locked */
+  __HAL_LOCK(hdma);
+  
+  if(HAL_DMA_STATE_READY == hdma->State)
+  {
+    switch (CallbackID)
+    {
+     case  HAL_DMA_XFER_CPLT_CB_ID:
+           hdma->XferCpltCallback = pCallback;
+           break;
+       
+     case  HAL_DMA_XFER_HALFCPLT_CB_ID:
+           hdma->XferHalfCpltCallback = pCallback;
+           break;         
+
+     case  HAL_DMA_XFER_ERROR_CB_ID:
+           hdma->XferErrorCallback = pCallback;
+           break;         
+           
+     case  HAL_DMA_XFER_ABORT_CB_ID:
+           hdma->XferAbortCallback = pCallback;
+           break; 
+           
+     default:
+           status = HAL_ERROR;
+           break;                                                            
+    }
+  }
+  else
+  {
+    status = HAL_ERROR;
+  } 
+  
+  /* Release Lock */
+  __HAL_UNLOCK(hdma);
+  
+  return status;
+}
+
+/**
+  * @brief  UnRegister callbacks
+  * @param  hdma                 pointer to a DMA_HandleTypeDef structure that contains
+  *                               the configuration information for the specified DMA Stream.
+  * @param  CallbackID           User Callback identifer
+  *                               a HAL_DMA_CallbackIDTypeDef ENUM as parameter.
+  * @retval HAL status
+  */              
+HAL_StatusTypeDef HAL_DMA_UnRegisterCallback(DMA_HandleTypeDef *hdma, HAL_DMA_CallbackIDTypeDef CallbackID)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+    /* Process locked */
+  __HAL_LOCK(hdma);
+  
+  if(HAL_DMA_STATE_READY == hdma->State)
+  {
+    switch (CallbackID)
+    {
+     case  HAL_DMA_XFER_CPLT_CB_ID:
+           hdma->XferCpltCallback = NULL;
+           break;
+       
+     case  HAL_DMA_XFER_HALFCPLT_CB_ID:
+           hdma->XferHalfCpltCallback = NULL;
+           break;         
+
+     case  HAL_DMA_XFER_ERROR_CB_ID:
+           hdma->XferErrorCallback = NULL;
+           break;         
+           
+     case  HAL_DMA_XFER_ABORT_CB_ID:
+           hdma->XferAbortCallback = NULL;
+           break; 
+     
+    case   HAL_DMA_XFER_ALL_CB_ID:
+           hdma->XferCpltCallback = NULL;
+           hdma->XferHalfCpltCallback = NULL;
+           hdma->XferErrorCallback = NULL;
+           hdma->XferAbortCallback = NULL;
+           break; 
+     
+    default:
+           status = HAL_ERROR;
+           break;                                                            
+    }
+  }
+  else
+  {
+    status = HAL_ERROR;
+  } 
+  
+  /* Release Lock */
+  __HAL_UNLOCK(hdma);
+  
+  return status;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Exported_Functions_Group3 Peripheral State functions
+ *  @brief    Peripheral State functions 
+ *
+@verbatim   
+ ===============================================================================
+                    ##### State and Errors functions #####
+ ===============================================================================  
+    [..]
+    This subsection provides functions allowing to
+      (+) Check the DMA state
+      (+) Get error code
+
+@endverbatim
+  * @{
+  */  
+
+/**
+  * @brief  Returns the DMA state.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.  
+  * @retval HAL state
+  */
+HAL_DMA_StateTypeDef HAL_DMA_GetState(DMA_HandleTypeDef *hdma)
+{
+  return hdma->State;
+}
+
+/**
+  * @brief  Return the DMA error code
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *              the configuration information for the specified DMA Channel.
+  * @retval DMA Error Code
+  */
+uint32_t HAL_DMA_GetError(DMA_HandleTypeDef *hdma)
+{
+  return hdma->ErrorCode;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup DMA_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Set the DMA Transfer parameters.
+  * @param  hdma       pointer to a DMA_HandleTypeDef structure that contains
+  *                     the configuration information for the specified DMA Channel.  
+  * @param  SrcAddress The source memory Buffer address
+  * @param  DstAddress The destination memory Buffer address
+  * @param  DataLength The length of data to be transferred from source to destination
+  * @retval HAL status
+  */
+static void DMA_SetConfig(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength)
+{
+	/* Clear all flags */
+  hdma->DmaBaseAddress->IFCR  = (DMA_FLAG_GL1 << hdma->ChannelIndex);
+  
+  /* Configure DMA Channel data length */
+  hdma->Instance->CNDTR = DataLength;
+  
+  /* Memory to Peripheral */
+  if((hdma->Init.Direction) == DMA_MEMORY_TO_PERIPH)
+  {   
+    /* Configure DMA Channel destination address */
+    hdma->Instance->CPAR = DstAddress;
+    
+    /* Configure DMA Channel source address */
+    hdma->Instance->CMAR = SrcAddress;
+  }
+  /* Peripheral to Memory */
+  else
+  {
+    /* Configure DMA Channel source address */
+    hdma->Instance->CPAR = SrcAddress;
+    
+    /* Configure DMA Channel destination address */
+    hdma->Instance->CMAR = DstAddress;
+  }
+}
+
+/**
+  * @brief  set the DMA base address and channel index depending on DMA instance
+  * @param  hdma       pointer to a DMA_HandleTypeDef structure that contains
+  *                     the configuration information for the specified DMA Stream. 
+  * @retval None
+  */
+static void DMA_CalcBaseAndBitshift(DMA_HandleTypeDef *hdma)
+{
+#if defined (DMA2)
+  /* calculation of the channel index */
+  if ((uint32_t)(hdma->Instance) < (uint32_t)(DMA2_Channel1))
+  {
+    /* DMA1 */
+    hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA1_Channel1) / ((uint32_t)DMA1_Channel2 - (uint32_t)DMA1_Channel1)) << 2U;
+    hdma->DmaBaseAddress = DMA1;
+  }
+  else 
+  {
+    /* DMA2 */
+    hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA2_Channel1) / ((uint32_t)DMA2_Channel2 - (uint32_t)DMA2_Channel1)) << 2U;
+    hdma->DmaBaseAddress = DMA2;
+  }
+#else
+  /* calculation of the channel index */
+  /* DMA1 */
+  hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA1_Channel1) / ((uint32_t)DMA1_Channel2 - (uint32_t)DMA1_Channel1)) << 2U;
+  hdma->DmaBaseAddress = DMA1;
+#endif
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+/**
+  * @}
+  */
+  
+  /**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_exti.c

@@ -0,0 +1,559 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_exti.c
+  * @author  MCD Application Team
+  * @brief   EXTI HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the Extended Interrupts and events controller (EXTI) peripheral:
+  *           + Initialization and de-initialization functions
+  *           + IO operation functions
+  *
+  @verbatim
+  ==============================================================================
+                    ##### EXTI Peripheral features #####
+  ==============================================================================
+  [..]
+    (+) Each Exti line can be configured within this driver.
+
+    (+) Exti line can be configured in 3 different modes
+        (++) Interrupt
+        (++) Event
+        (++) Both of them
+
+    (+) Configurable Exti lines can be configured with 3 different triggers
+        (++) Rising
+        (++) Falling
+        (++) Both of them
+
+    (+) When set in interrupt mode, configurable Exti lines have two different
+        interrupts pending registers which allow to distinguish which transition
+        occurs:
+        (++) Rising edge pending interrupt
+        (++) Falling
+
+    (+) Exti lines 0 to 15 are linked to gpio pin number 0 to 15. Gpio port can
+        be selected through multiplexer.
+
+                     ##### How to use this driver #####
+  ==============================================================================
+  [..]
+
+    (#) Configure the EXTI line using HAL_EXTI_SetConfigLine().
+        (++) Choose the interrupt line number by setting "Line" member from
+             EXTI_ConfigTypeDef structure.
+        (++) Configure the interrupt and/or event mode using "Mode" member from
+             EXTI_ConfigTypeDef structure.
+        (++) For configurable lines, configure rising and/or falling trigger
+             "Trigger" member from EXTI_ConfigTypeDef structure.
+        (++) For Exti lines linked to gpio, choose gpio port using "GPIOSel"
+             member from GPIO_InitTypeDef structure.
+
+    (#) Get current Exti configuration of a dedicated line using
+        HAL_EXTI_GetConfigLine().
+        (++) Provide exiting handle as parameter.
+        (++) Provide pointer on EXTI_ConfigTypeDef structure as second parameter.
+
+    (#) Clear Exti configuration of a dedicated line using HAL_EXTI_GetConfigLine().
+        (++) Provide exiting handle as parameter.
+
+    (#) Register callback to treat Exti interrupts using HAL_EXTI_RegisterCallback().
+        (++) Provide exiting handle as first parameter.
+        (++) Provide which callback will be registered using one value from
+             EXTI_CallbackIDTypeDef.
+        (++) Provide callback function pointer.
+
+    (#) Get interrupt pending bit using HAL_EXTI_GetPending().
+
+    (#) Clear interrupt pending bit using HAL_EXTI_GetPending().
+
+    (#) Generate software interrupt using HAL_EXTI_GenerateSWI().
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup EXTI
+  * @{
+  */
+/** MISRA C:2012 deviation rule has been granted for following rule:
+  * Rule-18.1_b - Medium: Array `EXTICR' 1st subscript interval [0,7] may be out
+  * of bounds [0,3] in following API :
+  * HAL_EXTI_SetConfigLine
+  * HAL_EXTI_GetConfigLine
+  * HAL_EXTI_ClearConfigLine
+  */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private defines -----------------------------------------------------------*/
+/** @defgroup EXTI_Private_Constants EXTI Private Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup EXTI_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup EXTI_Exported_Functions_Group1
+  *  @brief    Configuration functions
+  *
+@verbatim
+ ===============================================================================
+              ##### Configuration functions #####
+ ===============================================================================
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Set configuration of a dedicated Exti line.
+  * @param  hexti Exti handle.
+  * @param  pExtiConfig Pointer on EXTI configuration to be set.
+  * @retval HAL Status.
+  */
+HAL_StatusTypeDef HAL_EXTI_SetConfigLine(EXTI_HandleTypeDef *hexti, EXTI_ConfigTypeDef *pExtiConfig)
+{
+  uint32_t regval;
+  uint32_t linepos;
+  uint32_t maskline;
+
+  /* Check null pointer */
+  if ((hexti == NULL) || (pExtiConfig == NULL))
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check parameters */
+  assert_param(IS_EXTI_LINE(pExtiConfig->Line));
+  assert_param(IS_EXTI_MODE(pExtiConfig->Mode));
+
+  /* Assign line number to handle */
+  hexti->Line = pExtiConfig->Line;
+
+  /* Compute line mask */
+  linepos = (pExtiConfig->Line & EXTI_PIN_MASK);
+  maskline = (1uL << linepos);
+
+  /* Configure triggers for configurable lines */
+  if ((pExtiConfig->Line & EXTI_CONFIG) != 0x00u)
+  {
+    assert_param(IS_EXTI_TRIGGER(pExtiConfig->Trigger));
+
+    /* Configure rising trigger */
+    /* Mask or set line */
+    if ((pExtiConfig->Trigger & EXTI_TRIGGER_RISING) != 0x00u)
+    {
+      EXTI->RTSR |= maskline;
+    }
+    else
+    {
+      EXTI->RTSR &= ~maskline;
+    }
+
+    /* Configure falling trigger */
+    /* Mask or set line */
+    if ((pExtiConfig->Trigger & EXTI_TRIGGER_FALLING) != 0x00u)
+    {
+      EXTI->FTSR |= maskline;
+    }
+    else
+    {
+      EXTI->FTSR &= ~maskline;
+    }
+
+
+    /* Configure gpio port selection in case of gpio exti line */
+    if ((pExtiConfig->Line & EXTI_GPIO) == EXTI_GPIO)
+    {
+      assert_param(IS_EXTI_GPIO_PORT(pExtiConfig->GPIOSel));
+      assert_param(IS_EXTI_GPIO_PIN(linepos));
+
+      regval = SYSCFG->EXTICR[linepos >> 2u];
+      regval &= ~(SYSCFG_EXTICR1_EXTI0 << (SYSCFG_EXTICR1_EXTI1_Pos * (linepos & 0x03u)));
+      regval |= (pExtiConfig->GPIOSel << (SYSCFG_EXTICR1_EXTI1_Pos * (linepos & 0x03u)));
+      SYSCFG->EXTICR[linepos >> 2u] = regval;
+    }
+  }
+
+  /* Configure interrupt mode : read current mode */
+  /* Mask or set line */
+  if ((pExtiConfig->Mode & EXTI_MODE_INTERRUPT) != 0x00u)
+  {
+    EXTI->IMR |= maskline;
+  }
+  else
+  {
+    EXTI->IMR &= ~maskline;
+  }
+
+  /* Configure event mode : read current mode */
+  /* Mask or set line */
+  if ((pExtiConfig->Mode & EXTI_MODE_EVENT) != 0x00u)
+  {
+    EXTI->EMR |= maskline;
+  }
+  else
+  {
+    EXTI->EMR &= ~maskline;
+  }
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Get configuration of a dedicated Exti line.
+  * @param  hexti Exti handle.
+  * @param  pExtiConfig Pointer on structure to store Exti configuration.
+  * @retval HAL Status.
+  */
+HAL_StatusTypeDef HAL_EXTI_GetConfigLine(EXTI_HandleTypeDef *hexti, EXTI_ConfigTypeDef *pExtiConfig)
+{
+  uint32_t regval;
+  uint32_t linepos;
+  uint32_t maskline;
+
+  /* Check null pointer */
+  if ((hexti == NULL) || (pExtiConfig == NULL))
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check the parameter */
+  assert_param(IS_EXTI_LINE(hexti->Line));
+
+  /* Store handle line number to configuration structure */
+  pExtiConfig->Line = hexti->Line;
+
+  /* Compute line mask */
+  linepos = (pExtiConfig->Line & EXTI_PIN_MASK);
+  maskline = (1uL << linepos);
+
+  /* 1] Get core mode : interrupt */
+
+  /* Check if selected line is enable */
+  if ((EXTI->IMR & maskline) != 0x00u)
+  {
+    pExtiConfig->Mode = EXTI_MODE_INTERRUPT;
+  }
+  else
+  {
+    pExtiConfig->Mode = EXTI_MODE_NONE;
+  }
+
+  /* Get event mode */
+  /* Check if selected line is enable */
+  if ((EXTI->EMR & maskline) != 0x00u)
+  {
+    pExtiConfig->Mode |= EXTI_MODE_EVENT;
+  }
+
+  /* 2] Get trigger for configurable lines : rising */
+  if ((pExtiConfig->Line & EXTI_CONFIG) != 0x00u)
+  {
+    /* Check if configuration of selected line is enable */
+    if ((EXTI->RTSR & maskline) != 0x00u)
+    {
+      pExtiConfig->Trigger = EXTI_TRIGGER_RISING;
+    }
+    else
+    {
+      pExtiConfig->Trigger = EXTI_TRIGGER_NONE;
+    }
+
+    /* Get falling configuration */
+    /* Check if configuration of selected line is enable */
+    if ((EXTI->FTSR & maskline) != 0x00u)
+    {
+      pExtiConfig->Trigger |= EXTI_TRIGGER_FALLING;
+    }
+
+    /* Get Gpio port selection for gpio lines */
+    if ((pExtiConfig->Line & EXTI_GPIO) == EXTI_GPIO)
+    {
+      assert_param(IS_EXTI_GPIO_PIN(linepos));
+
+      regval = SYSCFG->EXTICR[linepos >> 2u];
+      pExtiConfig->GPIOSel = ((regval << (SYSCFG_EXTICR1_EXTI1_Pos * (3uL - (linepos & 0x03u)))) >> 24);
+    }
+    else
+    {
+      pExtiConfig->GPIOSel = 0x00u;
+    }
+  }
+  else
+  {
+    /* No Trigger selected */
+    pExtiConfig->Trigger = EXTI_TRIGGER_NONE;
+    pExtiConfig->GPIOSel = 0x00u;
+  }
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Clear whole configuration of a dedicated Exti line.
+  * @param  hexti Exti handle.
+  * @retval HAL Status.
+  */
+HAL_StatusTypeDef HAL_EXTI_ClearConfigLine(EXTI_HandleTypeDef *hexti)
+{
+  uint32_t regval;
+  uint32_t linepos;
+  uint32_t maskline;
+
+  /* Check null pointer */
+  if (hexti == NULL)
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check the parameter */
+  assert_param(IS_EXTI_LINE(hexti->Line));
+
+  /* compute line mask */
+  linepos = (hexti->Line & EXTI_PIN_MASK);
+  maskline = (1uL << linepos);
+
+  /* 1] Clear interrupt mode */
+  EXTI->IMR = (EXTI->IMR & ~maskline);
+
+  /* 2] Clear event mode */
+  EXTI->EMR = (EXTI->EMR & ~maskline);
+
+  /* 3] Clear triggers in case of configurable lines */
+  if ((hexti->Line & EXTI_CONFIG) != 0x00u)
+  {
+    EXTI->RTSR = (EXTI->RTSR & ~maskline);
+    EXTI->FTSR = (EXTI->FTSR & ~maskline);
+
+    /* Get Gpio port selection for gpio lines */
+    if ((hexti->Line & EXTI_GPIO) == EXTI_GPIO)
+    {
+      assert_param(IS_EXTI_GPIO_PIN(linepos));
+
+      regval = SYSCFG->EXTICR[linepos >> 2u];
+      regval &= ~(SYSCFG_EXTICR1_EXTI0 << (SYSCFG_EXTICR1_EXTI1_Pos * (linepos & 0x03u)));
+      SYSCFG->EXTICR[linepos >> 2u] = regval;
+    }
+  }
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Register callback for a dedicated Exti line.
+  * @param  hexti Exti handle.
+  * @param  CallbackID User callback identifier.
+  *         This parameter can be one of @arg @ref EXTI_CallbackIDTypeDef values.
+  * @param  pPendingCbfn function pointer to be stored as callback.
+  * @retval HAL Status.
+  */
+HAL_StatusTypeDef HAL_EXTI_RegisterCallback(EXTI_HandleTypeDef *hexti, EXTI_CallbackIDTypeDef CallbackID, void (*pPendingCbfn)(void))
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  switch (CallbackID)
+  {
+    case  HAL_EXTI_COMMON_CB_ID:
+      hexti->PendingCallback = pPendingCbfn;
+      break;
+
+    default:
+      status = HAL_ERROR;
+      break;
+  }
+
+  return status;
+}
+
+/**
+  * @brief  Store line number as handle private field.
+  * @param  hexti Exti handle.
+  * @param  ExtiLine Exti line number.
+  *         This parameter can be from 0 to @ref EXTI_LINE_NB.
+  * @retval HAL Status.
+  */
+HAL_StatusTypeDef HAL_EXTI_GetHandle(EXTI_HandleTypeDef *hexti, uint32_t ExtiLine)
+{
+  /* Check the parameters */
+  assert_param(IS_EXTI_LINE(ExtiLine));
+
+  /* Check null pointer */
+  if (hexti == NULL)
+  {
+    return HAL_ERROR;
+  }
+  else
+  {
+    /* Store line number as handle private field */
+    hexti->Line = ExtiLine;
+
+    return HAL_OK;
+  }
+}
+
+/**
+  * @}
+  */
+
+/** @addtogroup EXTI_Exported_Functions_Group2
+  *  @brief EXTI IO functions.
+  *
+@verbatim
+ ===============================================================================
+                       ##### IO operation functions #####
+ ===============================================================================
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Handle EXTI interrupt request.
+  * @param  hexti Exti handle.
+  * @retval none.
+  */
+void HAL_EXTI_IRQHandler(EXTI_HandleTypeDef *hexti)
+{
+  uint32_t regval;
+  uint32_t maskline;
+
+  /* Compute line mask */
+  maskline = (1uL << (hexti->Line & EXTI_PIN_MASK));
+
+  /* Get pending bit  */
+  regval = (EXTI->PR & maskline);
+  if (regval != 0x00u)
+  {
+    /* Clear pending bit */
+    EXTI->PR = maskline;
+
+    /* Call callback */
+    if (hexti->PendingCallback != NULL)
+    {
+      hexti->PendingCallback();
+    }
+  }
+}
+
+/**
+  * @brief  Get interrupt pending bit of a dedicated line.
+  * @param  hexti Exti handle.
+  * @param  Edge Specify which pending edge as to be checked.
+  *         This parameter can be one of the following values:
+  *           @arg @ref EXTI_TRIGGER_RISING_FALLING
+  *         This parameter is kept for compatibility with other series.
+  * @retval 1 if interrupt is pending else 0.
+  */
+uint32_t HAL_EXTI_GetPending(EXTI_HandleTypeDef *hexti, uint32_t Edge)
+{
+  uint32_t regval;
+  uint32_t linepos;
+  uint32_t maskline;
+
+  /* Check parameters */
+  assert_param(IS_EXTI_LINE(hexti->Line));
+  assert_param(IS_EXTI_CONFIG_LINE(hexti->Line));
+  assert_param(IS_EXTI_PENDING_EDGE(Edge));
+
+  /* Compute line mask */
+  linepos = (hexti->Line & EXTI_PIN_MASK);
+  maskline = (1uL << linepos);
+
+  /* return 1 if bit is set else 0 */
+  regval = ((EXTI->PR & maskline) >> linepos);
+  return regval;
+}
+
+/**
+  * @brief  Clear interrupt pending bit of a dedicated line.
+  * @param  hexti Exti handle.
+  * @param  Edge Specify which pending edge as to be clear.
+  *         This parameter can be one of the following values:
+  *           @arg @ref EXTI_TRIGGER_RISING_FALLING
+  *         This parameter is kept for compatibility with other series.
+  * @retval None.
+  */
+void HAL_EXTI_ClearPending(EXTI_HandleTypeDef *hexti, uint32_t Edge)
+{
+  uint32_t maskline;
+
+  /* Check parameters */
+  assert_param(IS_EXTI_LINE(hexti->Line));
+  assert_param(IS_EXTI_CONFIG_LINE(hexti->Line));
+  assert_param(IS_EXTI_PENDING_EDGE(Edge));
+
+  /* Compute line mask */
+  maskline = (1uL << (hexti->Line & EXTI_PIN_MASK));
+
+  /* Clear Pending bit */
+  EXTI->PR =  maskline;
+}
+
+/**
+  * @brief  Generate a software interrupt for a dedicated line.
+  * @param  hexti Exti handle.
+  * @retval None.
+  */
+void HAL_EXTI_GenerateSWI(EXTI_HandleTypeDef *hexti)
+{
+  uint32_t maskline;
+
+  /* Check parameters */
+  assert_param(IS_EXTI_LINE(hexti->Line));
+  assert_param(IS_EXTI_CONFIG_LINE(hexti->Line));
+
+  /* Compute line mask */
+  maskline = (1uL << (hexti->Line & EXTI_PIN_MASK));
+
+  /* Generate Software interrupt */
+  EXTI->SWIER = maskline;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_EXTI_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_flash.c

@@ -0,0 +1,694 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_flash.c
+  * @author  MCD Application Team
+  * @brief   FLASH HAL module driver.
+  *          This file provides firmware functions to manage the following 
+  *          functionalities of the internal FLASH memory:
+  *           + Program operations functions
+  *           + Memory Control functions 
+  *           + Peripheral State functions
+  *         
+  @verbatim
+  ==============================================================================
+                        ##### FLASH peripheral features #####
+  ==============================================================================
+  [..] The Flash memory interface manages CPU AHB I-Code and D-Code accesses 
+       to the Flash memory. It implements the erase and program Flash memory operations 
+       and the read and write protection mechanisms.
+
+  [..] The Flash memory interface accelerates code execution with a system of instruction
+      prefetch. 
+
+  [..] The FLASH main features are:
+      (+) Flash memory read operations
+      (+) Flash memory program/erase operations
+      (+) Read / write protections
+      (+) Prefetch on I-Code
+      (+) Option Bytes programming
+
+
+                     ##### How to use this driver #####
+  ==============================================================================
+  [..]                             
+      This driver provides functions and macros to configure and program the FLASH 
+      memory of all STM32F0xx devices.
+    
+      (#) FLASH Memory I/O Programming functions: this group includes all needed
+          functions to erase and program the main memory:
+        (++) Lock and Unlock the FLASH interface
+        (++) Erase function: Erase page, erase all pages
+        (++) Program functions: half word, word and doubleword
+      (#) FLASH Option Bytes Programming functions: this group includes all needed
+          functions to manage the Option Bytes:
+        (++) Lock and Unlock the Option Bytes
+        (++) Set/Reset the write protection
+        (++) Set the Read protection Level
+        (++) Program the user Option Bytes
+        (++) Launch the Option Bytes loader
+        (++) Erase Option Bytes
+        (++) Program the data Option Bytes
+        (++) Get the Write protection.
+        (++) Get the user option bytes.
+    
+      (#) Interrupts and flags management functions : this group 
+          includes all needed functions to:
+        (++) Handle FLASH interrupts
+        (++) Wait for last FLASH operation according to its status
+        (++) Get error flag status
+
+  [..] In addition to these function, this driver includes a set of macros allowing
+       to handle the following operations:
+      
+      (+) Set/Get the latency
+      (+) Enable/Disable the prefetch buffer
+      (+) Enable/Disable the FLASH interrupts
+      (+) Monitor the FLASH flags status
+          
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+
+/** @defgroup FLASH FLASH
+  * @brief FLASH HAL module driver
+  * @{
+  */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @defgroup FLASH_Private_Constants FLASH Private Constants
+  * @{
+  */
+/**
+  * @}
+  */
+
+/* Private macro ---------------------------- ---------------------------------*/
+/** @defgroup FLASH_Private_Macros FLASH Private Macros
+  * @{
+  */
+ 
+/**
+  * @}
+  */
+
+/* Private variables ---------------------------------------------------------*/
+/** @defgroup FLASH_Private_Variables FLASH Private Variables
+  * @{
+  */
+/* Variables used for Erase pages under interruption*/
+FLASH_ProcessTypeDef pFlash;
+/**
+  * @}
+  */
+
+/* Private function prototypes -----------------------------------------------*/
+/** @defgroup FLASH_Private_Functions FLASH Private Functions
+  * @{
+  */
+static  void   FLASH_Program_HalfWord(uint32_t Address, uint16_t Data);
+static  void   FLASH_SetErrorCode(void);
+extern void    FLASH_PageErase(uint32_t PageAddress);
+/**
+  * @}
+  */
+
+/* Exported functions ---------------------------------------------------------*/
+/** @defgroup FLASH_Exported_Functions FLASH Exported Functions
+  * @{
+  */
+  
+/** @defgroup FLASH_Exported_Functions_Group1 Programming operation functions 
+  *  @brief   Programming operation functions 
+  *
+@verbatim   
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Program halfword, word or double word at a specified address
+  * @note   The function HAL_FLASH_Unlock() should be called before to unlock the FLASH interface
+  *         The function HAL_FLASH_Lock() should be called after to lock the FLASH interface
+  *
+  * @note   If an erase and a program operations are requested simultaneously,    
+  *         the erase operation is performed before the program one.
+  *  
+  * @note   FLASH should be previously erased before new programming (only exception to this 
+  *         is when 0x0000 is programmed)
+  *
+  * @param  TypeProgram   Indicate the way to program at a specified address.
+  *                       This parameter can be a value of @ref FLASH_Type_Program
+  * @param  Address       Specifie the address to be programmed.
+  * @param  Data          Specifie the data to be programmed
+  * 
+  * @retval HAL_StatusTypeDef HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint64_t Data)
+{
+  HAL_StatusTypeDef status = HAL_ERROR;
+  uint8_t index = 0U;
+  uint8_t nbiterations = 0U;
+  
+  /* Process Locked */
+  __HAL_LOCK(&pFlash);
+
+  /* Check the parameters */
+  assert_param(IS_FLASH_TYPEPROGRAM(TypeProgram));
+  assert_param(IS_FLASH_PROGRAM_ADDRESS(Address));
+
+    /* Wait for last operation to be completed */
+    status = FLASH_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+  
+  if(status == HAL_OK)
+  {
+    if(TypeProgram == FLASH_TYPEPROGRAM_HALFWORD)
+    {
+      /* Program halfword (16-bit) at a specified address. */
+      nbiterations = 1U;
+    }
+    else if(TypeProgram == FLASH_TYPEPROGRAM_WORD)
+    {
+      /* Program word (32-bit = 2*16-bit) at a specified address. */
+      nbiterations = 2U;
+    }
+    else
+    {
+      /* Program double word (64-bit = 4*16-bit) at a specified address. */
+      nbiterations = 4U;
+    }
+
+    for (index = 0U; index < nbiterations; index++)
+    {
+      FLASH_Program_HalfWord((Address + (2U*index)), (uint16_t)(Data >> (16U*index)));
+
+        /* Wait for last operation to be completed */
+        status = FLASH_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+    
+        /* If the program operation is completed, disable the PG Bit */
+        CLEAR_BIT(FLASH->CR, FLASH_CR_PG);
+      /* In case of error, stop programming procedure */
+      if (status != HAL_OK)
+      {
+        break;
+      }
+    }
+  }
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(&pFlash);
+
+  return status;
+}
+
+/**
+  * @brief  Program halfword, word or double word at a specified address  with interrupt enabled.
+  * @note   The function HAL_FLASH_Unlock() should be called before to unlock the FLASH interface
+  *         The function HAL_FLASH_Lock() should be called after to lock the FLASH interface
+  *
+  * @note   If an erase and a program operations are requested simultaneously,    
+  *         the erase operation is performed before the program one.
+  *
+  * @param  TypeProgram  Indicate the way to program at a specified address.
+  *                      This parameter can be a value of @ref FLASH_Type_Program
+  * @param  Address      Specifie the address to be programmed.
+  * @param  Data         Specifie the data to be programmed
+  * 
+  * @retval HAL_StatusTypeDef HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint64_t Data)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+  
+  /* Process Locked */
+  __HAL_LOCK(&pFlash);
+
+  /* Check the parameters */
+  assert_param(IS_FLASH_TYPEPROGRAM(TypeProgram));
+  assert_param(IS_FLASH_PROGRAM_ADDRESS(Address));
+
+  /* Enable End of FLASH Operation and Error source interrupts */
+  __HAL_FLASH_ENABLE_IT(FLASH_IT_EOP | FLASH_IT_ERR);
+  
+  pFlash.Address = Address;
+  pFlash.Data = Data;
+
+  if(TypeProgram == FLASH_TYPEPROGRAM_HALFWORD)
+  {
+    pFlash.ProcedureOnGoing = FLASH_PROC_PROGRAMHALFWORD;
+    /* Program halfword (16-bit) at a specified address. */
+    pFlash.DataRemaining = 1U;
+  }
+  else if(TypeProgram == FLASH_TYPEPROGRAM_WORD)
+  {
+    pFlash.ProcedureOnGoing = FLASH_PROC_PROGRAMWORD;
+    /* Program word (32-bit : 2*16-bit) at a specified address. */
+    pFlash.DataRemaining = 2U;
+  }
+  else
+  {
+    pFlash.ProcedureOnGoing = FLASH_PROC_PROGRAMDOUBLEWORD;
+    /* Program double word (64-bit : 4*16-bit) at a specified address. */
+    pFlash.DataRemaining = 4U;
+  }
+
+  /* Program halfword (16-bit) at a specified address. */
+  FLASH_Program_HalfWord(Address, (uint16_t)Data);
+
+  return status;
+}
+
+/**
+  * @brief This function handles FLASH interrupt request.
+  * @retval None
+  */
+void HAL_FLASH_IRQHandler(void)
+{
+  uint32_t addresstmp = 0U;
+  
+  /* Check FLASH operation error flags */
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR) ||__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR))
+  {
+    /* Return the faulty address */
+    addresstmp = pFlash.Address;
+    /* Reset address */
+    pFlash.Address = 0xFFFFFFFFU;
+  
+    /* Save the Error code */
+    FLASH_SetErrorCode();
+    
+    /* FLASH error interrupt user callback */
+    HAL_FLASH_OperationErrorCallback(addresstmp);
+
+    /* Stop the procedure ongoing */
+    pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
+  }
+
+  /* Check FLASH End of Operation flag  */
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP))
+  {
+    /* Clear FLASH End of Operation pending bit */
+    __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP);
+    
+    /* Process can continue only if no error detected */
+    if(pFlash.ProcedureOnGoing != FLASH_PROC_NONE)
+    {
+      if(pFlash.ProcedureOnGoing == FLASH_PROC_PAGEERASE)
+      {
+        /* Nb of pages to erased can be decreased */
+        pFlash.DataRemaining--;
+
+        /* Check if there are still pages to erase */
+        if(pFlash.DataRemaining != 0U)
+        {
+          addresstmp = pFlash.Address;
+          /*Indicate user which sector has been erased */
+          HAL_FLASH_EndOfOperationCallback(addresstmp);
+
+          /*Increment sector number*/
+          addresstmp = pFlash.Address + FLASH_PAGE_SIZE;
+          pFlash.Address = addresstmp;
+
+          /* If the erase operation is completed, disable the PER Bit */
+          CLEAR_BIT(FLASH->CR, FLASH_CR_PER);
+
+          FLASH_PageErase(addresstmp);
+        }
+        else
+        {
+          /* No more pages to Erase, user callback can be called. */
+          /* Reset Sector and stop Erase pages procedure */
+          pFlash.Address = addresstmp = 0xFFFFFFFFU;
+          pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
+          /* FLASH EOP interrupt user callback */
+          HAL_FLASH_EndOfOperationCallback(addresstmp);
+        }
+      }
+      else if(pFlash.ProcedureOnGoing == FLASH_PROC_MASSERASE)
+      {
+        /* Operation is completed, disable the MER Bit */
+        CLEAR_BIT(FLASH->CR, FLASH_CR_MER);
+
+          /* MassErase ended. Return the selected bank */
+          /* FLASH EOP interrupt user callback */
+          HAL_FLASH_EndOfOperationCallback(0);
+
+          /* Stop Mass Erase procedure*/
+          pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
+        }
+      else
+      {
+        /* Nb of 16-bit data to program can be decreased */
+        pFlash.DataRemaining--;
+        
+        /* Check if there are still 16-bit data to program */
+        if(pFlash.DataRemaining != 0U)
+        {
+          /* Increment address to 16-bit */
+          pFlash.Address += 2;
+          addresstmp = pFlash.Address;
+          
+          /* Shift to have next 16-bit data */
+          pFlash.Data = (pFlash.Data >> 16U);
+          
+          /* Operation is completed, disable the PG Bit */
+          CLEAR_BIT(FLASH->CR, FLASH_CR_PG);
+
+          /*Program halfword (16-bit) at a specified address.*/
+          FLASH_Program_HalfWord(addresstmp, (uint16_t)pFlash.Data);
+        }
+        else
+        {
+          /* Program ended. Return the selected address */
+          /* FLASH EOP interrupt user callback */
+          if (pFlash.ProcedureOnGoing == FLASH_PROC_PROGRAMHALFWORD)
+          {
+            HAL_FLASH_EndOfOperationCallback(pFlash.Address);
+          }
+          else if (pFlash.ProcedureOnGoing == FLASH_PROC_PROGRAMWORD)
+          {
+            HAL_FLASH_EndOfOperationCallback(pFlash.Address - 2U);
+          }
+          else 
+          {
+            HAL_FLASH_EndOfOperationCallback(pFlash.Address - 6U);
+          }
+        
+          /* Reset Address and stop Program procedure */
+          pFlash.Address = 0xFFFFFFFFU;
+          pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
+        }
+      }
+    }
+  }
+  
+
+  if(pFlash.ProcedureOnGoing == FLASH_PROC_NONE)
+  {
+    /* Operation is completed, disable the PG, PER and MER Bits */
+    CLEAR_BIT(FLASH->CR, (FLASH_CR_PG | FLASH_CR_PER | FLASH_CR_MER));
+
+    /* Disable End of FLASH Operation and Error source interrupts */
+    __HAL_FLASH_DISABLE_IT(FLASH_IT_EOP | FLASH_IT_ERR);
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(&pFlash);
+  }
+}
+
+/**
+  * @brief  FLASH end of operation interrupt callback
+  * @param  ReturnValue The value saved in this parameter depends on the ongoing procedure
+  *                 - Mass Erase: No return value expected
+  *                 - Pages Erase: Address of the page which has been erased 
+  *                    (if 0xFFFFFFFF, it means that all the selected pages have been erased)
+  *                 - Program: Address which was selected for data program
+  * @retval none
+  */
+__weak void HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(ReturnValue);
+
+  /* NOTE : This function Should not be modified, when the callback is needed,
+            the HAL_FLASH_EndOfOperationCallback could be implemented in the user file
+   */ 
+}
+
+/**
+  * @brief  FLASH operation error interrupt callback
+  * @param  ReturnValue The value saved in this parameter depends on the ongoing procedure
+  *                 - Mass Erase: No return value expected
+  *                 - Pages Erase: Address of the page which returned an error
+  *                 - Program: Address which was selected for data program
+  * @retval none
+  */
+__weak void HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(ReturnValue);
+
+  /* NOTE : This function Should not be modified, when the callback is needed,
+            the HAL_FLASH_OperationErrorCallback could be implemented in the user file
+   */ 
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Exported_Functions_Group2 Peripheral Control functions 
+ *  @brief   management functions 
+ *
+@verbatim   
+ ===============================================================================
+                      ##### Peripheral Control functions #####
+ ===============================================================================  
+    [..]
+    This subsection provides a set of functions allowing to control the FLASH 
+    memory operations.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Unlock the FLASH control register access
+  * @retval HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_Unlock(void)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  if(READ_BIT(FLASH->CR, FLASH_CR_LOCK) != RESET)
+  {
+    /* Authorize the FLASH Registers access */
+    WRITE_REG(FLASH->KEYR, FLASH_KEY1);
+    WRITE_REG(FLASH->KEYR, FLASH_KEY2);
+
+    /* Verify Flash is unlocked */
+    if(READ_BIT(FLASH->CR, FLASH_CR_LOCK) != RESET)
+    {
+      status = HAL_ERROR;
+    }
+  }
+
+  return status;
+}
+
+/**
+  * @brief  Locks the FLASH control register access
+  * @retval HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_Lock(void)
+{
+  /* Set the LOCK Bit to lock the FLASH Registers access */
+  SET_BIT(FLASH->CR, FLASH_CR_LOCK);
+  
+  return HAL_OK;  
+}
+
+/**
+  * @brief  Unlock the FLASH Option Control Registers access.
+  * @retval HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void)
+{
+  if (HAL_IS_BIT_CLR(FLASH->CR, FLASH_CR_OPTWRE))
+  {
+    /* Authorizes the Option Byte register programming */
+    WRITE_REG(FLASH->OPTKEYR, FLASH_OPTKEY1);
+    WRITE_REG(FLASH->OPTKEYR, FLASH_OPTKEY2);
+  }
+  else
+  {
+    return HAL_ERROR;
+  }  
+  
+  return HAL_OK;  
+}
+
+/**
+  * @brief  Lock the FLASH Option Control Registers access.
+  * @retval HAL Status 
+  */
+HAL_StatusTypeDef HAL_FLASH_OB_Lock(void)
+{
+  /* Clear the OPTWRE Bit to lock the FLASH Option Byte Registers access */
+  CLEAR_BIT(FLASH->CR, FLASH_CR_OPTWRE);
+  
+  return HAL_OK;  
+}
+  
+/**
+  * @brief  Launch the option byte loading.
+  * @note   This function will reset automatically the MCU.
+  * @retval HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_OB_Launch(void)
+{
+  /* Set the OBL_Launch bit to launch the option byte loading */
+  SET_BIT(FLASH->CR, FLASH_CR_OBL_LAUNCH);
+  
+  /* Wait for last operation to be completed */
+  return(FLASH_WaitForLastOperation(FLASH_TIMEOUT_VALUE));
+}
+
+/**
+  * @}
+  */  
+
+/** @defgroup FLASH_Exported_Functions_Group3 Peripheral errors functions 
+ *  @brief    Peripheral errors functions 
+ *
+@verbatim   
+ ===============================================================================
+                      ##### Peripheral Errors functions #####
+ ===============================================================================  
+    [..]
+    This subsection permit to get in run-time errors of  the FLASH peripheral.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Get the specific FLASH error flag.
+  * @retval FLASH_ErrorCode The returned value can be:
+  *            @ref FLASH_Error_Codes
+  */
+uint32_t HAL_FLASH_GetError(void)
+{
+   return pFlash.ErrorCode;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Private_Functions
+ * @{
+ */
+
+/**
+  * @brief  Program a half-word (16-bit) at a specified address.
+  * @param  Address specify the address to be programmed.
+  * @param  Data    specify the data to be programmed.
+  * @retval None
+  */
+static void FLASH_Program_HalfWord(uint32_t Address, uint16_t Data)
+{
+  /* Clean the error context */
+  pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+  
+    /* Proceed to program the new data */
+    SET_BIT(FLASH->CR, FLASH_CR_PG);
+
+  /* Write data in the address */
+  *(__IO uint16_t*)Address = Data;
+}
+
+/**
+  * @brief  Wait for a FLASH operation to complete.
+  * @param  Timeout  maximum flash operation timeout
+  * @retval HAL Status
+  */
+HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout)
+{
+  /* Wait for the FLASH operation to complete by polling on BUSY flag to be reset.
+     Even if the FLASH operation fails, the BUSY flag will be reset and an error
+     flag will be set */
+     
+  uint32_t tickstart = HAL_GetTick();
+     
+  while(__HAL_FLASH_GET_FLAG(FLASH_FLAG_BSY)) 
+  { 
+    if (Timeout != HAL_MAX_DELAY)
+    {
+      if((Timeout == 0U) || ((HAL_GetTick()-tickstart) > Timeout))
+      {
+        return HAL_TIMEOUT;
+      }
+    }
+  }
+  
+  /* Check FLASH End of Operation flag  */
+  if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP))
+  {
+    /* Clear FLASH End of Operation pending bit */
+    __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP);
+  }
+  
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR)  || 
+     __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR))
+  {
+    /*Save the error code*/
+    FLASH_SetErrorCode();
+    return HAL_ERROR;
+  }
+
+  /* There is no error flag set */
+  return HAL_OK;
+}
+
+
+/**
+  * @brief  Set the specific FLASH error flag.
+  * @retval None
+  */
+static void FLASH_SetErrorCode(void)
+{
+  uint32_t flags = 0U;
+  
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR))
+  {
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_WRP;
+    flags |= FLASH_FLAG_WRPERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR))
+  {
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_PROG;
+    flags |= FLASH_FLAG_PGERR;
+  }
+  /* Clear FLASH error pending bits */
+  __HAL_FLASH_CLEAR_FLAG(flags);
+}  
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_flash_ex.c

@@ -0,0 +1,984 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_flash_ex.c
+  * @author  MCD Application Team
+  * @brief   Extended FLASH HAL module driver.
+  *    
+  *          This file provides firmware functions to manage the following 
+  *          functionalities of the FLASH peripheral:
+  *           + Extended Initialization/de-initialization functions
+  *           + Extended I/O operation functions
+  *           + Extended Peripheral Control functions 
+  *         
+  @verbatim
+  ==============================================================================
+               ##### Flash peripheral extended features  #####
+  ==============================================================================
+           
+                      ##### How to use this driver #####
+  ==============================================================================
+  [..] This driver provides functions to configure and program the FLASH memory 
+       of all STM32F0xxx devices. It includes
+       
+        (++) Set/Reset the write protection
+        (++) Program the user Option Bytes
+        (++) Get the Read protection Level
+  
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+#ifdef HAL_FLASH_MODULE_ENABLED
+
+/** @addtogroup FLASH
+  * @{
+  */
+/** @addtogroup FLASH_Private_Variables
+ * @{
+ */
+/* Variables used for Erase pages under interruption*/
+extern FLASH_ProcessTypeDef pFlash;
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+/** @defgroup FLASHEx FLASHEx
+  * @brief FLASH HAL Extension module driver
+  * @{
+  */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @defgroup FLASHEx_Private_Constants FLASHEx Private Constants
+ * @{
+ */
+#define FLASH_POSITION_IWDGSW_BIT        8U
+#define FLASH_POSITION_OB_USERDATA0_BIT  16U
+#define FLASH_POSITION_OB_USERDATA1_BIT  24U
+/**
+  * @}
+  */
+
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup FLASHEx_Private_Macros FLASHEx Private Macros
+  * @{
+  */
+/**
+  * @}
+  */ 
+
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/** @defgroup FLASHEx_Private_Functions FLASHEx Private Functions
+ * @{
+ */
+/* Erase operations */
+static void              FLASH_MassErase(void);
+void    FLASH_PageErase(uint32_t PageAddress);
+
+/* Option bytes control */
+static HAL_StatusTypeDef FLASH_OB_EnableWRP(uint32_t WriteProtectPage);
+static HAL_StatusTypeDef FLASH_OB_DisableWRP(uint32_t WriteProtectPage);
+static HAL_StatusTypeDef FLASH_OB_RDP_LevelConfig(uint8_t ReadProtectLevel);
+static HAL_StatusTypeDef FLASH_OB_UserConfig(uint8_t UserConfig);
+static HAL_StatusTypeDef FLASH_OB_ProgramData(uint32_t Address, uint8_t Data);
+static uint32_t          FLASH_OB_GetWRP(void);
+static uint32_t          FLASH_OB_GetRDP(void);
+static uint8_t           FLASH_OB_GetUser(void);
+
+/**
+  * @}
+  */
+
+/* Exported functions ---------------------------------------------------------*/
+/** @defgroup FLASHEx_Exported_Functions FLASHEx Exported Functions
+  * @{
+  */
+  
+/** @defgroup FLASHEx_Exported_Functions_Group1 FLASHEx Memory Erasing functions
+ *  @brief   FLASH Memory Erasing functions
+  *
+@verbatim   
+  ==============================================================================
+                ##### FLASH Erasing Programming functions ##### 
+  ==============================================================================
+
+    [..] The FLASH Memory Erasing functions, includes the following functions:
+    (+) @ref HAL_FLASHEx_Erase: return only when erase has been done
+    (+) @ref HAL_FLASHEx_Erase_IT: end of erase is done when @ref HAL_FLASH_EndOfOperationCallback 
+        is called with parameter 0xFFFFFFFF
+
+    [..] Any operation of erase should follow these steps:
+    (#) Call the @ref HAL_FLASH_Unlock() function to enable the flash control register and 
+        program memory access.
+    (#) Call the desired function to erase page.
+    (#) Call the @ref HAL_FLASH_Lock() to disable the flash program memory access 
+       (recommended to protect the FLASH memory against possible unwanted operation).
+
+@endverbatim
+  * @{
+  */
+  
+
+/**
+  * @brief  Perform a mass erase or erase the specified FLASH memory pages
+  * @note   To correctly run this function, the @ref HAL_FLASH_Unlock() function
+  *         must be called before.
+  *         Call the @ref HAL_FLASH_Lock() to disable the flash memory access 
+  *         (recommended to protect the FLASH memory against possible unwanted operation)
+  * @param[in]  pEraseInit pointer to an FLASH_EraseInitTypeDef structure that
+  *         contains the configuration information for the erasing.
+  *
+  * @param[out]  PageError pointer to variable  that
+  *         contains the configuration information on faulty page in case of error
+  *         (0xFFFFFFFF means that all the pages have been correctly erased)
+  *
+  * @retval HAL_StatusTypeDef HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef *pEraseInit, uint32_t *PageError)
+{
+  HAL_StatusTypeDef status = HAL_ERROR;
+  uint32_t address = 0U;
+
+  /* Process Locked */
+  __HAL_LOCK(&pFlash);
+
+  /* Check the parameters */
+  assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase));
+
+  if (pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE)
+  {
+      /* Mass Erase requested for Bank1 */
+      /* Wait for last operation to be completed */
+      if (FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE) == HAL_OK)
+      {
+        /*Mass erase to be done*/
+        FLASH_MassErase();
+        
+        /* Wait for last operation to be completed */
+        status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+        
+        /* If the erase operation is completed, disable the MER Bit */
+        CLEAR_BIT(FLASH->CR, FLASH_CR_MER);
+      }
+  }
+  else
+  {
+    /* Page Erase is requested */
+    /* Check the parameters */
+    assert_param(IS_FLASH_PROGRAM_ADDRESS(pEraseInit->PageAddress));
+    assert_param(IS_FLASH_NB_PAGES(pEraseInit->PageAddress, pEraseInit->NbPages));
+    
+      /* Page Erase requested on address located on bank1 */
+      /* Wait for last operation to be completed */
+      if (FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE) == HAL_OK)
+      {
+        /*Initialization of PageError variable*/
+        *PageError = 0xFFFFFFFFU;
+        
+        /* Erase page by page to be done*/
+        for(address = pEraseInit->PageAddress;
+            address < ((pEraseInit->NbPages * FLASH_PAGE_SIZE) + pEraseInit->PageAddress);
+            address += FLASH_PAGE_SIZE)
+        {
+          FLASH_PageErase(address);
+          
+          /* Wait for last operation to be completed */
+          status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+          
+          /* If the erase operation is completed, disable the PER Bit */
+          CLEAR_BIT(FLASH->CR, FLASH_CR_PER);
+          
+          if (status != HAL_OK)
+          {
+            /* In case of error, stop erase procedure and return the faulty address */
+            *PageError = address;
+            break;
+          }
+        }
+      }
+  }
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(&pFlash);
+
+  return status;
+}
+
+/**
+  * @brief  Perform a mass erase or erase the specified FLASH memory pages with interrupt enabled
+  * @note   To correctly run this function, the @ref HAL_FLASH_Unlock() function
+  *         must be called before.
+  *         Call the @ref HAL_FLASH_Lock() to disable the flash memory access 
+  *         (recommended to protect the FLASH memory against possible unwanted operation)
+  * @param  pEraseInit pointer to an FLASH_EraseInitTypeDef structure that
+  *         contains the configuration information for the erasing.
+  *
+  * @retval HAL_StatusTypeDef HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef *pEraseInit)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  /* Process Locked */
+  __HAL_LOCK(&pFlash);
+
+  /* If procedure already ongoing, reject the next one */
+  if (pFlash.ProcedureOnGoing != FLASH_PROC_NONE)
+  {
+    return HAL_ERROR;
+  }
+  
+  /* Check the parameters */
+  assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase));
+
+  /* Enable End of FLASH Operation and Error source interrupts */
+  __HAL_FLASH_ENABLE_IT(FLASH_IT_EOP | FLASH_IT_ERR);
+
+  if (pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE)
+  {
+    /*Mass erase to be done*/
+    pFlash.ProcedureOnGoing = FLASH_PROC_MASSERASE;
+        FLASH_MassErase();
+  }
+  else
+  {
+    /* Erase by page to be done*/
+
+    /* Check the parameters */
+    assert_param(IS_FLASH_PROGRAM_ADDRESS(pEraseInit->PageAddress));
+    assert_param(IS_FLASH_NB_PAGES(pEraseInit->PageAddress, pEraseInit->NbPages));
+
+    pFlash.ProcedureOnGoing = FLASH_PROC_PAGEERASE;
+    pFlash.DataRemaining = pEraseInit->NbPages;
+    pFlash.Address = pEraseInit->PageAddress;
+
+    /*Erase 1st page and wait for IT*/
+    FLASH_PageErase(pEraseInit->PageAddress);
+  }
+
+  return status;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Exported_Functions_Group2 Option Bytes Programming functions
+ *  @brief   Option Bytes Programming functions
+  *
+@verbatim   
+  ==============================================================================
+                ##### Option Bytes Programming functions ##### 
+  ==============================================================================  
+    [..]
+    This subsection provides a set of functions allowing to control the FLASH 
+    option bytes operations.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Erases the FLASH option bytes.
+  * @note   This functions erases all option bytes except the Read protection (RDP).
+  *         The function @ref HAL_FLASH_Unlock() should be called before to unlock the FLASH interface
+  *         The function @ref HAL_FLASH_OB_Unlock() should be called before to unlock the options bytes
+  *         The function @ref HAL_FLASH_OB_Launch() should be called after to force the reload of the options bytes
+  *         (system reset will occur)
+  * @retval HAL status
+  */
+
+HAL_StatusTypeDef HAL_FLASHEx_OBErase(void)
+{
+  uint8_t rdptmp = OB_RDP_LEVEL_0;
+  HAL_StatusTypeDef status = HAL_ERROR;
+
+  /* Get the actual read protection Option Byte value */
+  rdptmp = FLASH_OB_GetRDP();
+
+  /* Wait for last operation to be completed */
+  status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+
+  if(status == HAL_OK)
+  {
+    /* Clean the error context */
+    pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+    /* If the previous operation is completed, proceed to erase the option bytes */
+    SET_BIT(FLASH->CR, FLASH_CR_OPTER);
+    SET_BIT(FLASH->CR, FLASH_CR_STRT);
+
+    /* Wait for last operation to be completed */
+    status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+
+    /* If the erase operation is completed, disable the OPTER Bit */
+    CLEAR_BIT(FLASH->CR, FLASH_CR_OPTER);
+
+    if(status == HAL_OK)
+    {
+      /* Restore the last read protection Option Byte value */
+      status = FLASH_OB_RDP_LevelConfig(rdptmp);
+    }
+  }
+
+  /* Return the erase status */
+  return status;
+}
+
+/**
+  * @brief  Program option bytes
+  * @note   The function @ref HAL_FLASH_Unlock() should be called before to unlock the FLASH interface
+  *         The function @ref HAL_FLASH_OB_Unlock() should be called before to unlock the options bytes
+  *         The function @ref HAL_FLASH_OB_Launch() should be called after to force the reload of the options bytes
+  *         (system reset will occur)
+  *
+  * @param  pOBInit pointer to an FLASH_OBInitStruct structure that
+  *         contains the configuration information for the programming.
+  *
+  * @retval HAL_StatusTypeDef HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit)
+{
+  HAL_StatusTypeDef status = HAL_ERROR;
+
+  /* Process Locked */
+  __HAL_LOCK(&pFlash);
+
+  /* Check the parameters */
+  assert_param(IS_OPTIONBYTE(pOBInit->OptionType));
+
+  /* Write protection configuration */
+  if((pOBInit->OptionType & OPTIONBYTE_WRP) == OPTIONBYTE_WRP)
+  {
+    assert_param(IS_WRPSTATE(pOBInit->WRPState));
+    if (pOBInit->WRPState == OB_WRPSTATE_ENABLE)
+    {
+      /* Enable of Write protection on the selected page */
+      status = FLASH_OB_EnableWRP(pOBInit->WRPPage);
+    }
+    else
+    {
+      /* Disable of Write protection on the selected page */
+      status = FLASH_OB_DisableWRP(pOBInit->WRPPage);
+    }
+    if (status != HAL_OK)
+    {
+      /* Process Unlocked */
+      __HAL_UNLOCK(&pFlash);
+      return status;
+    }
+  }
+
+  /* Read protection configuration */
+  if((pOBInit->OptionType & OPTIONBYTE_RDP) == OPTIONBYTE_RDP)
+  {
+    status = FLASH_OB_RDP_LevelConfig(pOBInit->RDPLevel);
+    if (status != HAL_OK)
+    {
+      /* Process Unlocked */
+      __HAL_UNLOCK(&pFlash);
+      return status;
+    }
+  }
+
+  /* USER configuration */
+  if((pOBInit->OptionType & OPTIONBYTE_USER) == OPTIONBYTE_USER)
+  {
+    status = FLASH_OB_UserConfig(pOBInit->USERConfig);
+    if (status != HAL_OK)
+    {
+      /* Process Unlocked */
+      __HAL_UNLOCK(&pFlash);
+      return status;
+    }
+  }
+
+  /* DATA configuration*/
+  if((pOBInit->OptionType & OPTIONBYTE_DATA) == OPTIONBYTE_DATA)
+  {
+    status = FLASH_OB_ProgramData(pOBInit->DATAAddress, pOBInit->DATAData);
+    if (status != HAL_OK)
+    {
+      /* Process Unlocked */
+      __HAL_UNLOCK(&pFlash);
+      return status;
+    }
+  }
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(&pFlash);
+
+  return status;
+}
+
+/**
+  * @brief  Get the Option byte configuration
+  * @param  pOBInit pointer to an FLASH_OBInitStruct structure that
+  *         contains the configuration information for the programming.
+  *
+  * @retval None
+  */
+void HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef *pOBInit)
+{
+  pOBInit->OptionType = OPTIONBYTE_WRP | OPTIONBYTE_RDP | OPTIONBYTE_USER;
+
+  /*Get WRP*/
+  pOBInit->WRPPage = FLASH_OB_GetWRP();
+
+  /*Get RDP Level*/
+  pOBInit->RDPLevel = FLASH_OB_GetRDP();
+
+  /*Get USER*/
+  pOBInit->USERConfig = FLASH_OB_GetUser();
+}
+
+/**
+  * @brief  Get the Option byte user data
+  * @param  DATAAdress Address of the option byte DATA
+  *          This parameter can be one of the following values:
+  *            @arg @ref OB_DATA_ADDRESS_DATA0
+  *            @arg @ref OB_DATA_ADDRESS_DATA1
+  * @retval Value programmed in USER data
+  */
+uint32_t HAL_FLASHEx_OBGetUserData(uint32_t DATAAdress)
+{
+  uint32_t value = 0U;
+  
+  if (DATAAdress == OB_DATA_ADDRESS_DATA0)
+  {
+    /* Get value programmed in OB USER Data0 */
+    value = READ_BIT(FLASH->OBR, FLASH_OBR_DATA0) >> FLASH_POSITION_OB_USERDATA0_BIT;
+  }
+  else
+  {
+    /* Get value programmed in OB USER Data1 */
+    value = READ_BIT(FLASH->OBR, FLASH_OBR_DATA1) >> FLASH_POSITION_OB_USERDATA1_BIT;
+  }
+  
+  return value;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASHEx_Private_Functions
+ * @{
+ */
+
+/**
+  * @brief  Full erase of FLASH memory Bank 
+  *
+  * @retval None
+  */
+static void FLASH_MassErase(void)
+{
+  /* Clean the error context */
+  pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+    /* Only bank1 will be erased*/
+    SET_BIT(FLASH->CR, FLASH_CR_MER);
+    SET_BIT(FLASH->CR, FLASH_CR_STRT);
+}
+
+/**
+  * @brief  Enable the write protection of the desired pages
+  * @note   An option byte erase is done automatically in this function. 
+  * @note   When the memory read protection level is selected (RDP level = 1), 
+  *         it is not possible to program or erase the flash page i if
+  *         debug features are connected or boot code is executed in RAM, even if nWRPi = 1 
+  * 
+  * @param  WriteProtectPage specifies the page(s) to be write protected.
+  *         The value of this parameter depend on device used within the same series 
+  * @retval HAL status 
+  */
+static HAL_StatusTypeDef FLASH_OB_EnableWRP(uint32_t WriteProtectPage)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+  uint16_t WRP0_Data = 0xFFFFU;
+#if defined(OB_WRP1_WRP1)
+  uint16_t WRP1_Data = 0xFFFFU;
+#endif /* OB_WRP1_WRP1 */
+#if defined(OB_WRP2_WRP2)
+  uint16_t WRP2_Data = 0xFFFFU;
+#endif /* OB_WRP2_WRP2 */
+#if defined(OB_WRP3_WRP3)
+  uint16_t WRP3_Data = 0xFFFFU;
+#endif /* OB_WRP3_WRP3 */
+  
+  /* Check the parameters */
+  assert_param(IS_OB_WRP(WriteProtectPage));
+    
+  /* Get current write protected pages and the new pages to be protected ******/
+  WriteProtectPage = (uint32_t)(~((~FLASH_OB_GetWRP()) | WriteProtectPage));
+  
+#if defined(OB_WRP_PAGES0TO15MASK)
+  WRP0_Data = (uint16_t)(WriteProtectPage & OB_WRP_PAGES0TO15MASK);
+#elif defined(OB_WRP_PAGES0TO31MASK)
+  WRP0_Data = (uint16_t)(WriteProtectPage & OB_WRP_PAGES0TO31MASK);
+#endif /* OB_WRP_PAGES0TO31MASK */
+  
+#if defined(OB_WRP_PAGES16TO31MASK)
+  WRP1_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES16TO31MASK) >> 8U);
+#elif defined(OB_WRP_PAGES32TO63MASK)
+  WRP1_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES32TO63MASK) >> 8U);
+#endif /* OB_WRP_PAGES32TO63MASK */
+ 
+#if defined(OB_WRP_PAGES32TO47MASK)
+  WRP2_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES32TO47MASK) >> 16U);
+#endif /* OB_WRP_PAGES32TO47MASK */
+
+#if defined(OB_WRP_PAGES48TO63MASK)
+  WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES48TO63MASK) >> 24U); 
+#elif defined(OB_WRP_PAGES48TO127MASK)
+  WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES48TO127MASK) >> 24U); 
+#endif /* OB_WRP_PAGES48TO63MASK */
+  
+  /* Wait for last operation to be completed */
+  status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+
+  if(status == HAL_OK)
+  { 
+    /* Clean the error context */
+    pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+    /* To be able to write again option byte, need to perform a option byte erase */
+    status = HAL_FLASHEx_OBErase();
+    if (status == HAL_OK)  
+    {
+      /* Enable write protection */
+      SET_BIT(FLASH->CR, FLASH_CR_OPTPG);
+
+#if defined(OB_WRP0_WRP0)
+      if(WRP0_Data != 0xFFU)
+      {
+        OB->WRP0 &= WRP0_Data;
+        
+        /* Wait for last operation to be completed */
+        status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+      }
+#endif /* OB_WRP0_WRP0 */
+
+#if defined(OB_WRP1_WRP1)
+      if((status == HAL_OK) && (WRP1_Data != 0xFFU))
+      {
+        OB->WRP1 &= WRP1_Data;
+        
+        /* Wait for last operation to be completed */
+        status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+      }
+#endif /* OB_WRP1_WRP1 */
+
+#if defined(OB_WRP2_WRP2)
+      if((status == HAL_OK) && (WRP2_Data != 0xFFU))
+      {
+        OB->WRP2 &= WRP2_Data;
+        
+        /* Wait for last operation to be completed */
+        status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+      }
+#endif /* OB_WRP2_WRP2 */
+
+#if defined(OB_WRP3_WRP3)
+      if((status == HAL_OK) && (WRP3_Data != 0xFFU))
+      {
+        OB->WRP3 &= WRP3_Data;
+        
+        /* Wait for last operation to be completed */
+        status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+      }
+#endif /* OB_WRP3_WRP3 */
+
+      /* if the program operation is completed, disable the OPTPG Bit */
+      CLEAR_BIT(FLASH->CR, FLASH_CR_OPTPG);
+    }
+  }
+  
+  return status;
+}
+
+/**
+  * @brief  Disable the write protection of the desired pages
+  * @note   An option byte erase is done automatically in this function. 
+  * @note   When the memory read protection level is selected (RDP level = 1), 
+  *         it is not possible to program or erase the flash page i if   
+  *         debug features are connected or boot code is executed in RAM, even if nWRPi = 1 
+  * 
+  * @param  WriteProtectPage specifies the page(s) to be write unprotected.
+  *         The value of this parameter depend on device used within the same series 
+  * @retval HAL status 
+  */
+static HAL_StatusTypeDef FLASH_OB_DisableWRP(uint32_t WriteProtectPage)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+  uint16_t WRP0_Data = 0xFFFFU;
+#if defined(OB_WRP1_WRP1)
+  uint16_t WRP1_Data = 0xFFFFU;
+#endif /* OB_WRP1_WRP1 */
+#if defined(OB_WRP2_WRP2)
+  uint16_t WRP2_Data = 0xFFFFU;
+#endif /* OB_WRP2_WRP2 */
+#if defined(OB_WRP3_WRP3)
+  uint16_t WRP3_Data = 0xFFFFU;
+#endif /* OB_WRP3_WRP3 */
+  
+  /* Check the parameters */
+  assert_param(IS_OB_WRP(WriteProtectPage));
+
+  /* Get current write protected pages and the new pages to be unprotected ******/
+  WriteProtectPage = (FLASH_OB_GetWRP() | WriteProtectPage);
+
+#if defined(OB_WRP_PAGES0TO15MASK)
+  WRP0_Data = (uint16_t)(WriteProtectPage & OB_WRP_PAGES0TO15MASK);
+#elif defined(OB_WRP_PAGES0TO31MASK)
+  WRP0_Data = (uint16_t)(WriteProtectPage & OB_WRP_PAGES0TO31MASK);
+#endif /* OB_WRP_PAGES0TO31MASK */
+  
+#if defined(OB_WRP_PAGES16TO31MASK)
+  WRP1_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES16TO31MASK) >> 8U);
+#elif defined(OB_WRP_PAGES32TO63MASK)
+  WRP1_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES32TO63MASK) >> 8U);
+#endif /* OB_WRP_PAGES32TO63MASK */
+ 
+#if defined(OB_WRP_PAGES32TO47MASK)
+  WRP2_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES32TO47MASK) >> 16U);
+#endif /* OB_WRP_PAGES32TO47MASK */
+
+#if defined(OB_WRP_PAGES48TO63MASK)
+  WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES48TO63MASK) >> 24U); 
+#elif defined(OB_WRP_PAGES48TO127MASK)
+  WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES48TO127MASK) >> 24U); 
+#endif /* OB_WRP_PAGES48TO63MASK */
+
+    
+  /* Wait for last operation to be completed */
+  status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+
+  if(status == HAL_OK)
+  { 
+    /* Clean the error context */
+    pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+    /* To be able to write again option byte, need to perform a option byte erase */
+    status = HAL_FLASHEx_OBErase();
+    if (status == HAL_OK)  
+    {
+      SET_BIT(FLASH->CR, FLASH_CR_OPTPG);
+
+#if defined(OB_WRP0_WRP0)
+      if(WRP0_Data != 0xFFU)
+      {
+        OB->WRP0 &= WRP0_Data;
+        
+        /* Wait for last operation to be completed */
+        status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+      }
+#endif /* OB_WRP0_WRP0 */
+
+#if defined(OB_WRP1_WRP1)
+      if((status == HAL_OK) && (WRP1_Data != 0xFFU))
+      {
+        OB->WRP1 &= WRP1_Data;
+        
+        /* Wait for last operation to be completed */
+        status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+      }
+#endif /* OB_WRP1_WRP1 */
+
+#if defined(OB_WRP2_WRP2)
+      if((status == HAL_OK) && (WRP2_Data != 0xFFU))
+      {
+        OB->WRP2 &= WRP2_Data;
+        
+        /* Wait for last operation to be completed */
+        status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+      }
+#endif /* OB_WRP2_WRP2 */
+
+#if defined(OB_WRP3_WRP3)
+      if((status == HAL_OK) && (WRP3_Data != 0xFFU))
+      {
+        OB->WRP3 &= WRP3_Data;
+        
+        /* Wait for last operation to be completed */
+        status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+      }
+#endif /* OB_WRP3_WRP3 */
+
+      /* if the program operation is completed, disable the OPTPG Bit */
+      CLEAR_BIT(FLASH->CR, FLASH_CR_OPTPG);
+    }
+  }
+  return status;
+}
+
+/**
+  * @brief  Set the read protection level.
+  * @param  ReadProtectLevel specifies the read protection level.
+  *         This parameter can be one of the following values:
+  *            @arg @ref OB_RDP_LEVEL_0 No protection
+  *            @arg @ref OB_RDP_LEVEL_1 Read protection of the memory
+  *            @arg @ref OB_RDP_LEVEL_2 Full chip protection
+  * @note   Warning: When enabling OB_RDP level 2 it's no more possible to go back to level 1 or 0
+  * @retval HAL status
+  */
+static HAL_StatusTypeDef FLASH_OB_RDP_LevelConfig(uint8_t ReadProtectLevel)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+  
+  /* Check the parameters */
+  assert_param(IS_OB_RDP_LEVEL(ReadProtectLevel));
+  
+  /* Wait for last operation to be completed */
+  status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+  
+  if(status == HAL_OK)
+  { 
+    /* Clean the error context */
+    pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+    
+    /* If the previous operation is completed, proceed to erase the option bytes */
+    SET_BIT(FLASH->CR, FLASH_CR_OPTER);
+    SET_BIT(FLASH->CR, FLASH_CR_STRT);
+
+    /* Wait for last operation to be completed */
+    status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+
+    /* If the erase operation is completed, disable the OPTER Bit */
+    CLEAR_BIT(FLASH->CR, FLASH_CR_OPTER);
+
+    if(status == HAL_OK)
+    {
+      /* Enable the Option Bytes Programming operation */
+      SET_BIT(FLASH->CR, FLASH_CR_OPTPG);
+      
+      WRITE_REG(OB->RDP, ReadProtectLevel);
+      
+      /* Wait for last operation to be completed */
+      status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); 
+      
+      /* if the program operation is completed, disable the OPTPG Bit */
+      CLEAR_BIT(FLASH->CR, FLASH_CR_OPTPG);
+    }
+  }
+  
+  return status;
+}
+
+/**
+  * @brief  Program the FLASH User Option Byte.    
+  * @note   Programming of the OB should be performed only after an erase (otherwise PGERR occurs)
+  * @param  UserConfig The FLASH User Option Bytes values: IWDG_SW(Bit0), RST_STOP(Bit1), RST_STDBY(Bit2), nBOOT1(Bit4),
+  *         VDDA_Analog_Monitoring(Bit5) and SRAM_Parity_Enable(Bit6). 
+  *         For few devices, following option bytes are available: nBOOT0(Bit3) & BOOT_SEL(Bit7).
+  * @retval HAL status
+  */
+static HAL_StatusTypeDef FLASH_OB_UserConfig(uint8_t UserConfig)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  /* Check the parameters */
+  assert_param(IS_OB_IWDG_SOURCE((UserConfig&OB_IWDG_SW)));
+  assert_param(IS_OB_STOP_SOURCE((UserConfig&OB_STOP_NO_RST)));
+  assert_param(IS_OB_STDBY_SOURCE((UserConfig&OB_STDBY_NO_RST)));
+  assert_param(IS_OB_BOOT1((UserConfig&OB_BOOT1_SET)));
+  assert_param(IS_OB_VDDA_ANALOG((UserConfig&OB_VDDA_ANALOG_ON)));
+  assert_param(IS_OB_SRAM_PARITY((UserConfig&OB_SRAM_PARITY_RESET)));
+#if defined(FLASH_OBR_BOOT_SEL)
+  assert_param(IS_OB_BOOT_SEL((UserConfig&OB_BOOT_SEL_SET)));
+  assert_param(IS_OB_BOOT0((UserConfig&OB_BOOT0_SET)));
+#endif /* FLASH_OBR_BOOT_SEL */
+
+  /* Wait for last operation to be completed */
+  status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+  
+  if(status == HAL_OK)
+  {     
+    /* Clean the error context */
+    pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+    /* Enable the Option Bytes Programming operation */
+    SET_BIT(FLASH->CR, FLASH_CR_OPTPG); 
+ 
+#if defined(FLASH_OBR_BOOT_SEL)
+    OB->USER = UserConfig;
+#else
+    OB->USER = (UserConfig | 0x88U);
+#endif
+
+    /* Wait for last operation to be completed */
+    status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+
+    /* if the program operation is completed, disable the OPTPG Bit */
+    CLEAR_BIT(FLASH->CR, FLASH_CR_OPTPG);
+  }
+  
+  return status; 
+}
+
+/**
+  * @brief  Programs a half word at a specified Option Byte Data address.
+  * @note   The function @ref HAL_FLASH_Unlock() should be called before to unlock the FLASH interface
+  *         The function @ref HAL_FLASH_OB_Unlock() should be called before to unlock the options bytes
+  *         The function @ref HAL_FLASH_OB_Launch() should be called after to force the reload of the options bytes 
+  *         (system reset will occur)
+  *         Programming of the OB should be performed only after an erase (otherwise PGERR occurs)
+  * @param  Address specifies the address to be programmed.
+  *         This parameter can be 0x1FFFF804 or 0x1FFFF806. 
+  * @param  Data specifies the data to be programmed.
+  * @retval HAL status
+  */
+static HAL_StatusTypeDef FLASH_OB_ProgramData(uint32_t Address, uint8_t Data)
+{
+  HAL_StatusTypeDef status = HAL_ERROR;
+  
+  /* Check the parameters */
+  assert_param(IS_OB_DATA_ADDRESS(Address));
+  
+  /* Wait for last operation to be completed */
+  status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+  
+  if(status == HAL_OK)
+  {
+    /* Clean the error context */
+    pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+    /* Enables the Option Bytes Programming operation */
+    SET_BIT(FLASH->CR, FLASH_CR_OPTPG); 
+    *(__IO uint16_t*)Address = Data;
+    
+    /* Wait for last operation to be completed */
+    status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+    
+    /* If the program operation is completed, disable the OPTPG Bit */
+    CLEAR_BIT(FLASH->CR, FLASH_CR_OPTPG);
+  }
+  /* Return the Option Byte Data Program Status */
+  return status;
+}
+
+/**
+  * @brief  Return the FLASH Write Protection Option Bytes value.
+  * @retval The FLASH Write Protection Option Bytes value
+  */
+static uint32_t FLASH_OB_GetWRP(void)
+{
+  /* Return the FLASH write protection Register value */
+  return (uint32_t)(READ_REG(FLASH->WRPR));
+}
+
+/**
+  * @brief  Returns the FLASH Read Protection level.
+  * @retval FLASH RDP level
+  *         This parameter can be one of the following values:
+  *            @arg @ref OB_RDP_LEVEL_0 No protection
+  *            @arg @ref OB_RDP_LEVEL_1 Read protection of the memory
+  *            @arg @ref OB_RDP_LEVEL_2 Full chip protection
+  */
+static uint32_t FLASH_OB_GetRDP(void)
+{
+  uint32_t tmp_reg;
+  
+  /* Read RDP level bits */
+  tmp_reg = READ_BIT(FLASH->OBR, (FLASH_OBR_RDPRT1 | FLASH_OBR_RDPRT2));
+
+  if (tmp_reg == 0U)
+  {
+    return OB_RDP_LEVEL_0;
+  }
+  else if ((tmp_reg & FLASH_OBR_RDPRT2) == FLASH_OBR_RDPRT2)
+  {
+    return OB_RDP_LEVEL_2;
+  }
+  else 
+  {
+    return OB_RDP_LEVEL_1;
+  }
+}
+
+/**
+  * @brief  Return the FLASH User Option Byte value.
+  * @retval  The FLASH User Option Bytes values: IWDG_SW(Bit0), RST_STOP(Bit1), RST_STDBY(Bit2), nBOOT1(Bit4),
+  *         VDDA_Analog_Monitoring(Bit5) and SRAM_Parity_Enable(Bit6). 
+  *         For few devices, following option bytes are available: nBOOT0(Bit3) & BOOT_SEL(Bit7).
+  */
+static uint8_t FLASH_OB_GetUser(void)
+{
+  /* Return the User Option Byte */
+  return (uint8_t)((READ_REG(FLASH->OBR) & FLASH_OBR_USER) >> FLASH_POSITION_IWDGSW_BIT);
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH
+  * @{
+  */
+
+/** @addtogroup FLASH_Private_Functions
+ * @{
+ */
+
+/**
+  * @brief  Erase the specified FLASH memory page
+  * @param  PageAddress FLASH page to erase
+  *         The value of this parameter depend on device used within the same series      
+  * 
+  * @retval None
+  */
+void FLASH_PageErase(uint32_t PageAddress)
+{
+  /* Clean the error context */
+  pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+    /* Proceed to erase the page */
+    SET_BIT(FLASH->CR, FLASH_CR_PER);
+    WRITE_REG(FLASH->AR, PageAddress);
+    SET_BIT(FLASH->CR, FLASH_CR_STRT);
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_FLASH_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_gpio.c

@@ -0,0 +1,543 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_gpio.c
+  * @author  MCD Application Team
+  * @brief   GPIO HAL module driver.
+  *          This file provides firmware functions to manage the following 
+  *          functionalities of the General Purpose Input/Output (GPIO) peripheral:
+  *           + Initialization and de-initialization functions
+  *           + IO operation functions
+  *         
+  @verbatim
+  ==============================================================================
+                    ##### GPIO Peripheral features #####
+  ==============================================================================         
+  [..] 
+    (+) Each port bit of the general-purpose I/O (GPIO) ports can be individually
+  configured by software in several modes:
+        (++) Input mode
+        (++) Analog mode
+        (++) Output mode
+        (++) Alternate function mode
+        (++) External interrupt/event lines
+ 
+    (+) During and just after reset, the alternate functions and external interrupt
+  lines are not active and the I/O ports are configured in input floating mode.
+  
+    (+) All GPIO pins have weak internal pull-up and pull-down resistors, which can be
+  activated or not.
+           
+    (+) In Output or Alternate mode, each IO can be configured on open-drain or push-pull
+  type and the IO speed can be selected depending on the VDD value.
+       
+    (+) The microcontroller IO pins are connected to onboard peripherals/modules through a
+        multiplexer that allows only one peripheral alternate function (AF) connected
+  to an IO pin at a time. In this way, there can be no conflict between peripherals 
+  sharing the same IO pin. 
+  
+    (+) All ports have external interrupt/event capability. To use external interrupt
+  lines, the port must be configured in input mode. All available GPIO pins are 
+  connected to the 16 external interrupt/event lines from EXTI0 to EXTI15.
+  
+    (+) The external interrupt/event controller consists of up to 28 edge detectors
+        (16 lines are connected to GPIO) for generating event/interrupt requests (each
+        input line can be independently configured to select the type (interrupt or event)
+        and the corresponding trigger event (rising or falling or both). Each line can
+        also be masked independently.
+   
+            ##### How to use this driver #####
+  ==============================================================================  
+  [..]
+   (#) Enable the GPIO AHB clock using the following function : __HAL_RCC_GPIOx_CLK_ENABLE(). 
+                                    
+   (#) Configure the GPIO pin(s) using HAL_GPIO_Init().
+       (++) Configure the IO mode using "Mode" member from GPIO_InitTypeDef structure
+       (++) Activate Pull-up, Pull-down resistor using "Pull" member from GPIO_InitTypeDef 
+            structure.
+       (++) In case of Output or alternate function mode selection: the speed is 
+             configured through "Speed" member from GPIO_InitTypeDef structure.
+        (++) In alternate mode is selection, the alternate function connected to the IO
+             is configured through "Alternate" member from GPIO_InitTypeDef structure.
+       (++) Analog mode is required when a pin is to be used as ADC channel 
+            or DAC output.
+       (++) In case of external interrupt/event selection the "Mode" member from 
+            GPIO_InitTypeDef structure select the type (interrupt or event) and 
+            the corresponding trigger event (rising or falling or both).
+  
+   (#) In case of external interrupt/event mode selection, configure NVIC IRQ priority 
+       mapped to the EXTI line using HAL_NVIC_SetPriority() and enable it using
+       HAL_NVIC_EnableIRQ().
+  
+   (#) HAL_GPIO_DeInit allows to set register values to their reset value. It's also 
+       recommended to use it to unconfigure pin which was used as an external interrupt 
+       or in event mode. That's the only way to reset corresponding bit in EXTI & SYSCFG 
+       registers.
+  
+   (#) To get the level of a pin configured in input mode use HAL_GPIO_ReadPin().
+  
+   (#) To set/reset the level of a pin configured in output mode use 
+       HAL_GPIO_WritePin()/HAL_GPIO_TogglePin().
+  
+   (#) To lock pin configuration until next reset use HAL_GPIO_LockPin().
+  
+   (#) During and just after reset, the alternate functions are not 
+       active and the GPIO pins are configured in input floating mode (except JTAG
+       pins).
+  
+   (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general purpose 
+       (PC14 and PC15, respectively) when the LSE oscillator is off. The LSE has 
+       priority over the GPIO function.
+  
+   (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as 
+        general purpose PF0 and PF1, respectively, when the HSE oscillator is off.
+       The HSE has priority over the GPIO function.
+  
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup GPIO GPIO
+  * @brief GPIO HAL module driver
+  * @{
+  */
+
+/** MISRA C:2012 deviation rule has been granted for following rules:
+  * Rule-18.1_d - Medium: Array pointer `GPIOx' is accessed with index [..,..]
+  * which may be out of array bounds [..,UNKNOWN] in following APIs:
+  * HAL_GPIO_Init
+  * HAL_GPIO_DeInit
+  */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private defines -----------------------------------------------------------*/
+/** @defgroup GPIO_Private_Defines GPIO Private Defines
+  * @{
+  */
+#define GPIO_MODE             (0x00000003U)
+#define EXTI_MODE             (0x10000000U)
+#define GPIO_MODE_IT          (0x00010000U)
+#define GPIO_MODE_EVT         (0x00020000U)
+#define RISING_EDGE           (0x00100000U)
+#define FALLING_EDGE          (0x00200000U)
+#define GPIO_OUTPUT_TYPE      (0x00000010U)
+
+#define GPIO_NUMBER           (16U)
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Exported functions --------------------------------------------------------*/
+
+/** @defgroup GPIO_Exported_Functions GPIO Exported Functions
+  * @{
+  */
+
+/** @defgroup GPIO_Exported_Functions_Group1 Initialization/de-initialization functions 
+ *  @brief    Initialization and Configuration functions 
+ *
+@verbatim    
+ ===============================================================================
+              ##### Initialization and de-initialization functions #####
+ ===============================================================================
+ 
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Initialize the GPIOx peripheral according to the specified parameters in the GPIO_Init.
+  * @param  GPIOx where x can be (A..F) to select the GPIO peripheral for STM32F0 family
+  * @param  GPIO_Init pointer to a GPIO_InitTypeDef structure that contains
+  *         the configuration information for the specified GPIO peripheral.
+  * @retval None
+  */
+void HAL_GPIO_Init(GPIO_TypeDef  *GPIOx, GPIO_InitTypeDef *GPIO_Init)
+{ 
+  uint32_t position = 0x00u;
+  uint32_t iocurrent;
+  uint32_t temp;
+
+  /* Check the parameters */
+  assert_param(IS_GPIO_ALL_INSTANCE(GPIOx));
+  assert_param(IS_GPIO_PIN(GPIO_Init->Pin));
+  assert_param(IS_GPIO_MODE(GPIO_Init->Mode));
+  assert_param(IS_GPIO_PULL(GPIO_Init->Pull));
+
+  /* Configure the port pins */
+  while (((GPIO_Init->Pin) >> position) != 0x00u)
+  {
+    /* Get current io position */
+    iocurrent = (GPIO_Init->Pin) & (1uL << position);
+
+    if (iocurrent != 0x00u)
+    {
+      /*--------------------- GPIO Mode Configuration ------------------------*/
+      /* In case of Output or Alternate function mode selection */
+      if((GPIO_Init->Mode == GPIO_MODE_OUTPUT_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_PP) ||
+         (GPIO_Init->Mode == GPIO_MODE_OUTPUT_OD) || (GPIO_Init->Mode == GPIO_MODE_AF_OD))
+      {
+        /* Check the Speed parameter */
+        assert_param(IS_GPIO_SPEED(GPIO_Init->Speed));
+        /* Configure the IO Speed */
+        temp = GPIOx->OSPEEDR;
+        temp &= ~(GPIO_OSPEEDER_OSPEEDR0 << (position * 2u));
+        temp |= (GPIO_Init->Speed << (position * 2u));
+        GPIOx->OSPEEDR = temp;
+
+        /* Configure the IO Output Type */
+        temp = GPIOx->OTYPER;
+        temp &= ~(GPIO_OTYPER_OT_0 << position) ;
+        temp |= (((GPIO_Init->Mode & GPIO_OUTPUT_TYPE) >> 4u) << position);
+        GPIOx->OTYPER = temp;
+      }
+
+      /* Activate the Pull-up or Pull down resistor for the current IO */
+      temp = GPIOx->PUPDR;
+      temp &= ~(GPIO_PUPDR_PUPDR0 << (position * 2u));
+      temp |= ((GPIO_Init->Pull) << (position * 2u));
+      GPIOx->PUPDR = temp;
+
+      /* In case of Alternate function mode selection */
+      if((GPIO_Init->Mode == GPIO_MODE_AF_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_OD))
+      {
+        /* Check the Alternate function parameters */
+        assert_param(IS_GPIO_AF_INSTANCE(GPIOx));
+        assert_param(IS_GPIO_AF(GPIO_Init->Alternate));
+
+        /* Configure Alternate function mapped with the current IO */
+        temp = GPIOx->AFR[position >> 3u];
+        temp &= ~(0xFu << ((position & 0x07u) * 4u));
+        temp |= ((GPIO_Init->Alternate) << ((position & 0x07u) * 4u));
+        GPIOx->AFR[position >> 3u] = temp;
+      }
+
+      /* Configure IO Direction mode (Input, Output, Alternate or Analog) */
+      temp = GPIOx->MODER;
+      temp &= ~(GPIO_MODER_MODER0 << (position * 2u));
+      temp |= ((GPIO_Init->Mode & GPIO_MODE) << (position * 2u));
+      GPIOx->MODER = temp;
+
+      /*--------------------- EXTI Mode Configuration ------------------------*/
+      /* Configure the External Interrupt or event for the current IO */
+      if((GPIO_Init->Mode & EXTI_MODE) == EXTI_MODE)
+      {
+        /* Enable SYSCFG Clock */
+        __HAL_RCC_SYSCFG_CLK_ENABLE();
+
+        temp = SYSCFG->EXTICR[position >> 2u];
+        temp &= ~(0x0FuL << (4u * (position & 0x03u)));
+        temp |= (GPIO_GET_INDEX(GPIOx) << (4u * (position & 0x03u)));
+        SYSCFG->EXTICR[position >> 2u] = temp;
+
+        /* Clear EXTI line configuration */
+        temp = EXTI->IMR;
+        temp &= ~(iocurrent);
+        if((GPIO_Init->Mode & GPIO_MODE_IT) == GPIO_MODE_IT)
+        {
+          temp |= iocurrent;
+        }
+        EXTI->IMR = temp;
+
+        temp = EXTI->EMR;
+        temp &= ~(iocurrent);
+        if((GPIO_Init->Mode & GPIO_MODE_EVT) == GPIO_MODE_EVT)
+        {
+          temp |= iocurrent;
+        }
+        EXTI->EMR = temp;
+
+        /* Clear Rising Falling edge configuration */
+        temp = EXTI->RTSR;
+        temp &= ~(iocurrent);
+        if((GPIO_Init->Mode & RISING_EDGE) == RISING_EDGE)
+        {
+          temp |= iocurrent;
+        }
+        EXTI->RTSR = temp;
+
+        temp = EXTI->FTSR;
+        temp &= ~(iocurrent);
+        if((GPIO_Init->Mode & FALLING_EDGE) == FALLING_EDGE)
+        {
+          temp |= iocurrent;
+        }
+        EXTI->FTSR = temp;
+      }
+    }
+
+    position++;
+  } 
+}
+
+/**
+  * @brief  De-initialize the GPIOx peripheral registers to their default reset values.
+  * @param  GPIOx where x can be (A..F) to select the GPIO peripheral for STM32F0 family
+  * @param  GPIO_Pin specifies the port bit to be written.
+  *         This parameter can be one of GPIO_PIN_x where x can be (0..15).
+  * @retval None
+  */
+void HAL_GPIO_DeInit(GPIO_TypeDef  *GPIOx, uint32_t GPIO_Pin)
+{
+  uint32_t position = 0x00u;
+  uint32_t iocurrent;
+  uint32_t tmp;
+
+  /* Check the parameters */
+  assert_param(IS_GPIO_ALL_INSTANCE(GPIOx));
+  assert_param(IS_GPIO_PIN(GPIO_Pin));
+
+  /* Configure the port pins */
+  while ((GPIO_Pin >> position) != 0x00u)
+  {
+    /* Get current io position */
+    iocurrent = (GPIO_Pin) & (1uL << position);
+
+    if (iocurrent != 0x00u)
+    {
+      /*------------------------- EXTI Mode Configuration --------------------*/
+      /* Clear the External Interrupt or Event for the current IO */
+
+      tmp = SYSCFG->EXTICR[position >> 2u];
+      tmp &= (0x0FuL << (4u * (position & 0x03u)));
+      if (tmp == (GPIO_GET_INDEX(GPIOx) << (4u * (position & 0x03u))))
+      {
+        /* Clear EXTI line configuration */
+        EXTI->IMR &= ~((uint32_t)iocurrent);
+        EXTI->EMR &= ~((uint32_t)iocurrent);
+        
+        /* Clear Rising Falling edge configuration */
+        EXTI->RTSR &= ~((uint32_t)iocurrent);
+        EXTI->FTSR &= ~((uint32_t)iocurrent);
+
+        /* Configure the External Interrupt or event for the current IO */
+        tmp = 0x0FuL << (4u * (position & 0x03u));
+        SYSCFG->EXTICR[position >> 2u] &= ~tmp;
+      }
+
+      /*------------------------- GPIO Mode Configuration --------------------*/
+      /* Configure IO Direction in Input Floating Mode */
+      GPIOx->MODER &= ~(GPIO_MODER_MODER0 << (position * 2u));
+
+      /* Configure the default Alternate Function in current IO */
+      GPIOx->AFR[position >> 3u] &= ~(0xFu << ((uint32_t)(position & 0x07u) * 4u)) ;
+
+      /* Deactivate the Pull-up and Pull-down resistor for the current IO */
+      GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPDR0 << (position * 2u));
+
+      /* Configure the default value IO Output Type */
+      GPIOx->OTYPER  &= ~(GPIO_OTYPER_OT_0 << position) ;
+
+      /* Configure the default value for IO Speed */
+      GPIOx->OSPEEDR &= ~(GPIO_OSPEEDER_OSPEEDR0 << (position * 2u));
+
+    }
+
+    position++;
+  }
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup GPIO_Exported_Functions_Group2 IO operation functions 
+ *  @brief GPIO Read, Write, Toggle, Lock and EXTI management functions.
+ *
+@verbatim   
+ ===============================================================================
+                       ##### IO operation functions #####
+ ===============================================================================  
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Read the specified input port pin.
+  * @param  GPIOx where x can be (A..F) to select the GPIO peripheral for STM32F0 family
+  * @param  GPIO_Pin specifies the port bit to read.
+  *         This parameter can be GPIO_PIN_x where x can be (0..15).
+  * @retval The input port pin value.
+  */
+GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
+{
+  GPIO_PinState bitstatus;
+
+  /* Check the parameters */
+  assert_param(IS_GPIO_PIN(GPIO_Pin));
+
+  if ((GPIOx->IDR & GPIO_Pin) != (uint32_t)GPIO_PIN_RESET)
+  {
+    bitstatus = GPIO_PIN_SET;
+  }
+  else
+  {
+    bitstatus = GPIO_PIN_RESET;
+  }
+  return bitstatus;
+  }
+
+/**
+  * @brief  Set or clear the selected data port bit.
+  * @note   This function uses GPIOx_BSRR and GPIOx_BRR registers to allow atomic read/modify
+  *         accesses. In this way, there is no risk of an IRQ occurring between
+  *         the read and the modify access.
+  *
+  * @param  GPIOx where x can be (A..H) to select the GPIO peripheral for STM32F0 family
+  * @param  GPIO_Pin specifies the port bit to be written.
+  *          This parameter can be one of GPIO_PIN_x where x can be (0..15).
+  * @param  PinState specifies the value to be written to the selected bit.
+  *          This parameter can be one of the GPIO_PinState enum values:
+  *            @arg GPIO_PIN_RESET: to clear the port pin
+  *            @arg GPIO_PIN_SET: to set the port pin
+  * @retval None
+  */
+void HAL_GPIO_WritePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState)
+{
+  /* Check the parameters */
+  assert_param(IS_GPIO_PIN(GPIO_Pin));
+  assert_param(IS_GPIO_PIN_ACTION(PinState));
+
+  if (PinState != GPIO_PIN_RESET)
+  {
+    GPIOx->BSRR = (uint32_t)GPIO_Pin;
+  }
+  else
+  {
+    GPIOx->BRR = (uint32_t)GPIO_Pin;
+  }
+}
+  
+/**
+  * @brief  Toggle the specified GPIO pin.
+  * @param  GPIOx where x can be (A..F) to select the GPIO peripheral for STM32F0 family
+  * @param  GPIO_Pin specifies the pin to be toggled.
+  * @retval None
+  */
+void HAL_GPIO_TogglePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
+{
+  uint32_t odr;
+
+  /* Check the parameters */
+  assert_param(IS_GPIO_PIN(GPIO_Pin));
+
+  /* get current Ouput Data Register value */
+  odr = GPIOx->ODR;
+
+  /* Set selected pins that were at low level, and reset ones that were high */
+  GPIOx->BSRR = ((odr & GPIO_Pin) << GPIO_NUMBER) | (~odr & GPIO_Pin);
+}
+
+/**
+* @brief  Locks GPIO Pins configuration registers.
+* @note   The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR,
+*         GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH.
+* @note   The configuration of the locked GPIO pins can no longer be modified
+*         until the next reset.
+  * @param  GPIOx where x can be (A..F) to select the GPIO peripheral for STM32F0 family
+  * @param  GPIO_Pin specifies the port bits to be locked.
+*         This parameter can be any combination of GPIO_Pin_x where x can be (0..15).
+* @retval None
+*/
+HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
+{
+  __IO uint32_t tmp = GPIO_LCKR_LCKK;
+
+  /* Check the parameters */
+  assert_param(IS_GPIO_LOCK_INSTANCE(GPIOx));
+  assert_param(IS_GPIO_PIN(GPIO_Pin));
+
+  /* Apply lock key write sequence */
+  SET_BIT(tmp, GPIO_Pin);
+  /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */
+  GPIOx->LCKR = tmp;
+  /* Reset LCKx bit(s): LCKK='0' + LCK[15-0] */
+  GPIOx->LCKR = GPIO_Pin;
+  /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */
+  GPIOx->LCKR = tmp;
+  /* Read LCKK register. This read is mandatory to complete key lock sequence */
+  tmp = GPIOx->LCKR;
+
+  /* read again in order to confirm lock is active */
+ if((GPIOx->LCKR & GPIO_LCKR_LCKK) != 0x00u)
+  {
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_ERROR;
+  }
+}
+
+/**
+  * @brief  Handle EXTI interrupt request.
+  * @param  GPIO_Pin Specifies the port pin connected to corresponding EXTI line.
+  * @retval None
+  */
+void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin)
+{
+  /* EXTI line interrupt detected */
+  if(__HAL_GPIO_EXTI_GET_IT(GPIO_Pin) != 0x00u)
+  { 
+    __HAL_GPIO_EXTI_CLEAR_IT(GPIO_Pin);
+    HAL_GPIO_EXTI_Callback(GPIO_Pin);
+  }
+}
+
+/**
+  * @brief  EXTI line detection callback.
+  * @param  GPIO_Pin Specifies the port pin connected to corresponding EXTI line.
+  * @retval None
+  */
+__weak void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(GPIO_Pin);
+
+  /* NOTE: This function should not be modified, when the callback is needed,
+            the HAL_GPIO_EXTI_Callback could be implemented in the user file
+   */ 
+}
+
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */
+
+#endif /* HAL_GPIO_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_i2c_ex.c

@@ -0,0 +1,333 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_i2c_ex.c
+  * @author  MCD Application Team
+  * @brief   I2C Extended HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of I2C Extended peripheral:
+  *           + Extended features functions
+  *
+  @verbatim
+  ==============================================================================
+               ##### I2C peripheral Extended features  #####
+  ==============================================================================
+
+  [..] Comparing to other previous devices, the I2C interface for STM32F0xx
+       devices contains the following additional features
+
+       (+) Possibility to disable or enable Analog Noise Filter
+       (+) Use of a configured Digital Noise Filter
+       (+) Disable or enable wakeup from Stop mode(s)
+       (+) Disable or enable Fast Mode Plus
+
+                     ##### How to use this driver #####
+  ==============================================================================
+  [..] This driver provides functions to configure Noise Filter and Wake Up Feature
+    (#) Configure I2C Analog noise filter using the function HAL_I2CEx_ConfigAnalogFilter()
+    (#) Configure I2C Digital noise filter using the function HAL_I2CEx_ConfigDigitalFilter()
+    (#) Configure the enable or disable of I2C Wake Up Mode using the functions :
+          (++) HAL_I2CEx_EnableWakeUp()
+          (++) HAL_I2CEx_DisableWakeUp()
+    (#) Configure the enable or disable of fast mode plus driving capability using the functions :
+          (++) HAL_I2CEx_EnableFastModePlus()
+          (++) HAL_I2CEx_DisableFastModePlus()
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup I2CEx I2CEx
+  * @brief I2C Extended HAL module driver
+  * @{
+  */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup I2CEx_Exported_Functions I2C Extended Exported Functions
+  * @{
+  */
+
+/** @defgroup I2CEx_Exported_Functions_Group1 Extended features functions
+  * @brief    Extended features functions
+  *
+@verbatim
+ ===============================================================================
+                      ##### Extended features functions #####
+ ===============================================================================
+    [..] This section provides functions allowing to:
+      (+) Configure Noise Filters
+      (+) Configure Wake Up Feature
+      (+) Configure Fast Mode Plus
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Configure I2C Analog noise filter.
+  * @param  hi2c Pointer to a I2C_HandleTypeDef structure that contains
+  *                the configuration information for the specified I2Cx peripheral.
+  * @param  AnalogFilter New state of the Analog filter.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_I2CEx_ConfigAnalogFilter(I2C_HandleTypeDef *hi2c, uint32_t AnalogFilter)
+{
+  /* Check the parameters */
+  assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance));
+  assert_param(IS_I2C_ANALOG_FILTER(AnalogFilter));
+
+  if (hi2c->State == HAL_I2C_STATE_READY)
+  {
+    /* Process Locked */
+    __HAL_LOCK(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_BUSY;
+
+    /* Disable the selected I2C peripheral */
+    __HAL_I2C_DISABLE(hi2c);
+
+    /* Reset I2Cx ANOFF bit */
+    hi2c->Instance->CR1 &= ~(I2C_CR1_ANFOFF);
+
+    /* Set analog filter bit*/
+    hi2c->Instance->CR1 |= AnalogFilter;
+
+    __HAL_I2C_ENABLE(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hi2c);
+
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+
+/**
+  * @brief  Configure I2C Digital noise filter.
+  * @param  hi2c Pointer to a I2C_HandleTypeDef structure that contains
+  *                the configuration information for the specified I2Cx peripheral.
+  * @param  DigitalFilter Coefficient of digital noise filter between Min_Data=0x00 and Max_Data=0x0F.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_I2CEx_ConfigDigitalFilter(I2C_HandleTypeDef *hi2c, uint32_t DigitalFilter)
+{
+  uint32_t tmpreg;
+
+  /* Check the parameters */
+  assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance));
+  assert_param(IS_I2C_DIGITAL_FILTER(DigitalFilter));
+
+  if (hi2c->State == HAL_I2C_STATE_READY)
+  {
+    /* Process Locked */
+    __HAL_LOCK(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_BUSY;
+
+    /* Disable the selected I2C peripheral */
+    __HAL_I2C_DISABLE(hi2c);
+
+    /* Get the old register value */
+    tmpreg = hi2c->Instance->CR1;
+
+    /* Reset I2Cx DNF bits [11:8] */
+    tmpreg &= ~(I2C_CR1_DNF);
+
+    /* Set I2Cx DNF coefficient */
+    tmpreg |= DigitalFilter << 8U;
+
+    /* Store the new register value */
+    hi2c->Instance->CR1 = tmpreg;
+
+    __HAL_I2C_ENABLE(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hi2c);
+
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+#if defined(I2C_CR1_WUPEN)
+
+/**
+  * @brief  Enable I2C wakeup from Stop mode(s).
+  * @param  hi2c Pointer to a I2C_HandleTypeDef structure that contains
+  *                the configuration information for the specified I2Cx peripheral.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_I2CEx_EnableWakeUp(I2C_HandleTypeDef *hi2c)
+{
+  /* Check the parameters */
+  assert_param(IS_I2C_WAKEUP_FROMSTOP_INSTANCE(hi2c->Instance));
+
+  if (hi2c->State == HAL_I2C_STATE_READY)
+  {
+    /* Process Locked */
+    __HAL_LOCK(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_BUSY;
+
+    /* Disable the selected I2C peripheral */
+    __HAL_I2C_DISABLE(hi2c);
+
+    /* Enable wakeup from stop mode */
+    hi2c->Instance->CR1 |= I2C_CR1_WUPEN;
+
+    __HAL_I2C_ENABLE(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hi2c);
+
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+
+/**
+  * @brief  Disable I2C wakeup from Stop mode(s).
+  * @param  hi2c Pointer to a I2C_HandleTypeDef structure that contains
+  *                the configuration information for the specified I2Cx peripheral.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_I2CEx_DisableWakeUp(I2C_HandleTypeDef *hi2c)
+{
+  /* Check the parameters */
+  assert_param(IS_I2C_WAKEUP_FROMSTOP_INSTANCE(hi2c->Instance));
+
+  if (hi2c->State == HAL_I2C_STATE_READY)
+  {
+    /* Process Locked */
+    __HAL_LOCK(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_BUSY;
+
+    /* Disable the selected I2C peripheral */
+    __HAL_I2C_DISABLE(hi2c);
+
+    /* Enable wakeup from stop mode */
+    hi2c->Instance->CR1 &= ~(I2C_CR1_WUPEN);
+
+    __HAL_I2C_ENABLE(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hi2c);
+
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+#endif
+
+/**
+  * @brief Enable the I2C fast mode plus driving capability.
+  * @param ConfigFastModePlus Selects the pin.
+  *   This parameter can be one of the @ref I2CEx_FastModePlus values
+  * @note  For I2C1, fast mode plus driving capability can be enabled on all selected
+  *        I2C1 pins using I2C_FASTMODEPLUS_I2C1 parameter or independently
+  *        on each one of the following pins PB6, PB7, PB8 and PB9.
+  * @note  For remaining I2C1 pins (PA14, PA15...) fast mode plus driving capability
+  *        can be enabled only by using I2C_FASTMODEPLUS_I2C1 parameter.
+  * @note  For all I2C2 pins fast mode plus driving capability can be enabled
+  *        only by using I2C_FASTMODEPLUS_I2C2 parameter.
+  * @retval None
+  */
+void HAL_I2CEx_EnableFastModePlus(uint32_t ConfigFastModePlus)
+{
+  /* Check the parameter */
+  assert_param(IS_I2C_FASTMODEPLUS(ConfigFastModePlus));
+
+  /* Enable SYSCFG clock */
+  __HAL_RCC_SYSCFG_CLK_ENABLE();
+
+  /* Enable fast mode plus driving capability for selected pin */
+  SET_BIT(SYSCFG->CFGR1, (uint32_t)ConfigFastModePlus);
+}
+
+/**
+  * @brief Disable the I2C fast mode plus driving capability.
+  * @param ConfigFastModePlus Selects the pin.
+  *   This parameter can be one of the @ref I2CEx_FastModePlus values
+  * @note  For I2C1, fast mode plus driving capability can be disabled on all selected
+  *        I2C1 pins using I2C_FASTMODEPLUS_I2C1 parameter or independently
+  *        on each one of the following pins PB6, PB7, PB8 and PB9.
+  * @note  For remaining I2C1 pins (PA14, PA15...) fast mode plus driving capability
+  *        can be disabled only by using I2C_FASTMODEPLUS_I2C1 parameter.
+  * @note  For all I2C2 pins fast mode plus driving capability can be disabled
+  *        only by using I2C_FASTMODEPLUS_I2C2 parameter.
+  * @retval None
+  */
+void HAL_I2CEx_DisableFastModePlus(uint32_t ConfigFastModePlus)
+{
+  /* Check the parameter */
+  assert_param(IS_I2C_FASTMODEPLUS(ConfigFastModePlus));
+
+  /* Enable SYSCFG clock */
+  __HAL_RCC_SYSCFG_CLK_ENABLE();
+
+  /* Disable fast mode plus driving capability for selected pin */
+  CLEAR_BIT(SYSCFG->CFGR1, (uint32_t)ConfigFastModePlus);
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_I2C_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_pwr.c

@@ -0,0 +1,454 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_pwr.c
+  * @author  MCD Application Team
+  * @brief   PWR HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the Power Controller (PWR) peripheral:
+  *           + Initialization/de-initialization function
+  *           + Peripheral Control function
+  *
+  @verbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup PWR PWR
+  * @brief PWR HAL module driver
+  * @{
+  */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup PWR_Exported_Functions PWR Exported Functions
+  * @{
+  */
+
+/** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions 
+  *  @brief    Initialization and de-initialization functions
+  *
+@verbatim
+ ===============================================================================
+              ##### Initialization and de-initialization functions #####
+ ===============================================================================
+    [..]
+      After reset, the backup domain (RTC registers, RTC backup data
+      registers) is protected against possible unwanted
+      write accesses.
+      To enable access to the RTC Domain and RTC registers, proceed as follows:
+        (+) Enable the Power Controller (PWR) APB1 interface clock using the
+            __HAL_RCC_PWR_CLK_ENABLE() macro.
+        (+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief Deinitializes the PWR peripheral registers to their default reset values.
+  * @retval None
+  */
+void HAL_PWR_DeInit(void)
+{
+  __HAL_RCC_PWR_FORCE_RESET();
+  __HAL_RCC_PWR_RELEASE_RESET();
+}
+
+/**
+  * @brief Enables access to the backup domain (RTC registers, RTC
+  *         backup data registers when present).
+  * @note  If the HSE divided by 32 is used as the RTC clock, the
+  *         Backup Domain Access should be kept enabled.
+  * @retval None
+  */
+void HAL_PWR_EnableBkUpAccess(void)
+{
+  PWR->CR |= (uint32_t)PWR_CR_DBP;
+}
+
+/**
+  * @brief Disables access to the backup domain (RTC registers, RTC
+  *         backup data registers when present).
+  * @note  If the HSE divided by 32 is used as the RTC clock, the
+  *         Backup Domain Access should be kept enabled.
+  * @retval None
+  */
+void HAL_PWR_DisableBkUpAccess(void)
+{
+  PWR->CR &= ~((uint32_t)PWR_CR_DBP);
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Exported_Functions_Group2 Peripheral Control functions 
+  *  @brief Low Power modes configuration functions
+  *
+@verbatim
+
+ ===============================================================================
+                 ##### Peripheral Control functions #####
+ ===============================================================================
+    
+    *** WakeUp pin configuration ***
+    ================================
+    [..]
+      (+) WakeUp pin is used to wakeup the system from Standby mode. This pin is
+          forced in input pull down configuration and is active on rising edges.
+      (+) There are two WakeUp pins, and up to eight Wakeup pins on STM32F07x & STM32F09x devices.
+         (++)WakeUp Pin 1 on PA.00.
+         (++)WakeUp Pin 2 on PC.13.
+         (++)WakeUp Pin 3 on PE.06.(STM32F07x/STM32F09x)
+         (++)WakeUp Pin 4 on PA.02.(STM32F07x/STM32F09x)
+         (++)WakeUp Pin 5 on PC.05.(STM32F07x/STM32F09x)
+         (++)WakeUp Pin 6 on PB.05.(STM32F07x/STM32F09x)
+         (++)WakeUp Pin 7 on PB.15.(STM32F07x/STM32F09x)
+         (++)WakeUp Pin 8 on PF.02.(STM32F07x/STM32F09x)
+
+    *** Low Power modes configuration ***
+    =====================================
+    [..]
+      The devices feature 3 low-power modes:
+      (+) Sleep mode: Cortex-M0 core stopped, peripherals kept running.
+      (+) Stop mode: all clocks are stopped, regulator running, regulator
+          in low power mode
+      (+) Standby mode: 1.2V domain powered off (mode not available on STM32F0x8 devices).
+
+   *** Sleep mode ***
+   ==================
+    [..]
+      (+) Entry:
+          The Sleep mode is entered by using the HAL_PWR_EnterSLEEPMode(PWR_MAINREGULATOR_ON, PWR_SLEEPENTRY_WFx)
+              functions with
+          (++) PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
+          (++) PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
+     
+      (+) Exit:
+        (++) Any peripheral interrupt acknowledged by the nested vectored interrupt
+              controller (NVIC) can wake up the device from Sleep mode.
+
+   *** Stop mode ***
+   =================
+    [..]
+      In Stop mode, all clocks in the 1.8V domain are stopped, the PLL, the HSI,
+      and the HSE RC oscillators are disabled. Internal SRAM and register contents
+      are preserved.
+      The voltage regulator can be configured either in normal or low-power mode.
+      To minimize the consumption.
+
+      (+) Entry:
+          The Stop mode is entered using the HAL_PWR_EnterSTOPMode(PWR_MAINREGULATOR_ON, PWR_STOPENTRY_WFI )
+             function with:
+          (++) Main regulator ON.
+          (++) Low Power regulator ON.
+          (++) PWR_STOPENTRY_WFI: enter STOP mode with WFI instruction
+          (++) PWR_STOPENTRY_WFE: enter STOP mode with WFE instruction
+      (+) Exit:
+          (++) Any EXTI Line (Internal or External) configured in Interrupt/Event mode.
+          (++) Some specific communication peripherals (CEC, USART, I2C) interrupts, 
+               when programmed in wakeup mode (the peripheral must be 
+               programmed in wakeup mode and the corresponding interrupt vector 
+               must be enabled in the NVIC)
+
+   *** Standby mode ***
+   ====================
+     [..]
+      The Standby mode allows to achieve the lowest power consumption. It is based
+      on the Cortex-M0 deep sleep mode, with the voltage regulator disabled.
+      The 1.8V domain is consequently powered off. The PLL, the HSI oscillator and
+      the HSE oscillator are also switched off. SRAM and register contents are lost
+      except for the RTC registers, RTC backup registers and Standby circuitry.
+      The voltage regulator is OFF.
+
+      (+) Entry:
+          (++) The Standby mode is entered using the HAL_PWR_EnterSTANDBYMode() function.
+      (+) Exit:
+          (++) WKUP pin rising edge, RTC alarm (Alarm A), RTC wakeup,
+               tamper event, time-stamp event, external reset in NRST pin, IWDG reset.
+
+   *** Auto-wakeup (AWU) from low-power mode ***
+   =============================================
+    [..]
+      The MCU can be woken up from low-power mode by an RTC Alarm event, an RTC
+      Wakeup event, a tamper event, a time-stamp event, or a comparator event, 
+      without depending on an external interrupt (Auto-wakeup mode).
+
+    (+) RTC auto-wakeup (AWU) from the Stop and Standby modes
+
+      (++) To wake up from the Stop mode with an RTC alarm event, it is necessary to
+            configure the RTC to generate the RTC alarm using the HAL_RTC_SetAlarm_IT() function.
+
+      (++) To wake up from the Stop mode with an RTC Tamper or time stamp event, it
+           is necessary to configure the RTC to detect the tamper or time stamp event using the
+           HAL_RTC_SetTimeStamp_IT() or HAL_RTC_SetTamper_IT() functions.
+
+      (++) To wake up from the Stop mode with an RTC WakeUp event, it is necessary to
+           configure the RTC to generate the RTC WakeUp event using the HAL_RTC_SetWakeUpTimer_IT() function.
+
+    (+) Comparator auto-wakeup (AWU) from the Stop mode
+
+      (++) To wake up from the Stop mode with a comparator wakeup event, it is necessary to:
+           (+++) Configure the EXTI Line associated with the comparator (example EXTI Line 22 for comparator 2) 
+                 to be sensitive to to the selected edges (falling, rising or falling 
+                 and rising) (Interrupt or Event modes) using the EXTI_Init() function.
+           (+++) Configure the comparator to generate the event.      
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief Enables the WakeUp PINx functionality.
+  * @param WakeUpPinx Specifies the Power Wake-Up pin to enable.
+  *         This parameter can be value of :
+  *           @ref PWREx_WakeUp_Pins
+  * @retval None
+  */
+void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx)
+{
+  /* Check the parameters */
+  assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx));
+  /* Enable the EWUPx pin */
+  SET_BIT(PWR->CSR, WakeUpPinx);
+}
+
+/**
+  * @brief Disables the WakeUp PINx functionality.
+  * @param WakeUpPinx Specifies the Power Wake-Up pin to disable.
+  *         This parameter can be values of :
+  *           @ref PWREx_WakeUp_Pins
+  * @retval None
+  */
+void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx)
+{
+  /* Check the parameters */
+  assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx));
+  /* Disable the EWUPx pin */
+  CLEAR_BIT(PWR->CSR, WakeUpPinx);
+}
+
+/**
+  * @brief Enters Sleep mode.
+  * @note  In Sleep mode, all I/O pins keep the same state as in Run mode.
+  * @param Regulator Specifies the regulator state in SLEEP mode.
+  *           On STM32F0 devices, this parameter is a dummy value and it is ignored
+  *           as regulator can't be modified in this mode. Parameter is kept for platform
+  *           compatibility.
+  * @param SLEEPEntry Specifies if SLEEP mode is entered with WFI or WFE instruction.
+  *           When WFI entry is used, tick interrupt have to be disabled if not desired as 
+  *           the interrupt wake up source.
+  *           This parameter can be one of the following values:
+  *            @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
+  *            @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
+  * @retval None
+  */
+void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry)
+{
+  /* Check the parameters */
+  assert_param(IS_PWR_REGULATOR(Regulator));
+  assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry));
+
+  /* Clear SLEEPDEEP bit of Cortex System Control Register */
+  SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk);
+
+  /* Select SLEEP mode entry -------------------------------------------------*/
+  if(SLEEPEntry == PWR_SLEEPENTRY_WFI)
+  {
+    /* Request Wait For Interrupt */
+    __WFI();
+  }
+  else
+  {
+    /* Request Wait For Event */
+    __SEV();
+    __WFE();
+    __WFE();
+  }
+}
+
+/**
+  * @brief Enters STOP mode.
+  * @note  In Stop mode, all I/O pins keep the same state as in Run mode.
+  * @note  When exiting Stop mode by issuing an interrupt or a wakeup event,
+  *         the HSI RC oscillator is selected as system clock.
+  * @note  When the voltage regulator operates in low power mode, an additional
+  *         startup delay is incurred when waking up from Stop mode.
+  *         By keeping the internal regulator ON during Stop mode, the consumption
+  *         is higher although the startup time is reduced.
+  * @param Regulator Specifies the regulator state in STOP mode.
+  *          This parameter can be one of the following values:
+  *            @arg PWR_MAINREGULATOR_ON: STOP mode with regulator ON
+  *            @arg PWR_LOWPOWERREGULATOR_ON: STOP mode with low power regulator ON
+  * @param STOPEntry specifies if STOP mode in entered with WFI or WFE instruction.
+  *          This parameter can be one of the following values:
+  *            @arg PWR_STOPENTRY_WFI:Enter STOP mode with WFI instruction
+  *            @arg PWR_STOPENTRY_WFE: Enter STOP mode with WFE instruction
+  * @retval None
+  */
+void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry)
+{
+  uint32_t tmpreg = 0;
+
+  /* Check the parameters */
+  assert_param(IS_PWR_REGULATOR(Regulator));
+  assert_param(IS_PWR_STOP_ENTRY(STOPEntry));
+
+  /* Select the regulator state in STOP mode ---------------------------------*/
+  tmpreg = PWR->CR;
+  
+  /* Clear PDDS and LPDS bits */
+  tmpreg &= (uint32_t)~(PWR_CR_PDDS | PWR_CR_LPDS);
+
+  /* Set LPDS bit according to Regulator value */
+  tmpreg |= Regulator;
+
+  /* Store the new value */
+  PWR->CR = tmpreg;
+
+  /* Set SLEEPDEEP bit of Cortex System Control Register */
+  SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
+
+  /* Select STOP mode entry --------------------------------------------------*/
+  if(STOPEntry == PWR_STOPENTRY_WFI)
+  {
+    /* Request Wait For Interrupt */
+    __WFI();
+  }
+  else
+  {
+    /* Request Wait For Event */
+    __SEV();
+    __WFE();
+    __WFE();
+  }
+
+  /* Reset SLEEPDEEP bit of Cortex System Control Register */
+  SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk);
+}
+
+/**
+  * @brief Enters STANDBY mode.
+  * @note  In Standby mode, all I/O pins are high impedance except for:
+  *          - Reset pad (still available)
+  *          - RTC alternate function pins if configured for tamper, time-stamp, RTC
+  *            Alarm out, or RTC clock calibration out.
+  *          - WKUP pins if enabled.
+  *            STM32F0x8 devices, the Stop mode is available, but it is 
+  *            aningless to distinguish between voltage regulator in Low power 
+  *            mode and voltage regulator in Run mode because the regulator 
+  *            not used and the core is supplied directly from an external source.
+  *            Consequently, the Standby mode is not available on those devices.
+  * @retval None
+  */
+void HAL_PWR_EnterSTANDBYMode(void)
+{
+  /* Select STANDBY mode */
+  PWR->CR |= (uint32_t)PWR_CR_PDDS;
+
+  /* Set SLEEPDEEP bit of Cortex System Control Register */
+  SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
+
+  /* This option is used to ensure that store operations are completed */
+#if defined ( __CC_ARM)
+  __force_stores();
+#endif
+  /* Request Wait For Interrupt */
+  __WFI();
+}
+
+/**
+  * @brief Indicates Sleep-On-Exit when returning from Handler mode to Thread mode. 
+  * @note Set SLEEPONEXIT bit of SCR register. When this bit is set, the processor 
+  *       re-enters SLEEP mode when an interruption handling is over.
+  *       Setting this bit is useful when the processor is expected to run only on
+  *       interruptions handling.         
+  * @retval None
+  */
+void HAL_PWR_EnableSleepOnExit(void)
+{
+  /* Set SLEEPONEXIT bit of Cortex System Control Register */
+  SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk));
+}
+
+
+/**
+  * @brief Disables Sleep-On-Exit feature when returning from Handler mode to Thread mode. 
+  * @note Clears SLEEPONEXIT bit of SCR register. When this bit is set, the processor 
+  *       re-enters SLEEP mode when an interruption handling is over.          
+  * @retval None
+  */
+void HAL_PWR_DisableSleepOnExit(void)
+{
+  /* Clear SLEEPONEXIT bit of Cortex System Control Register */
+  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk));
+}
+
+
+
+/**
+  * @brief Enables CORTEX M4 SEVONPEND bit. 
+  * @note Sets SEVONPEND bit of SCR register. When this bit is set, this causes 
+  *       WFE to wake up when an interrupt moves from inactive to pended.
+  * @retval None
+  */
+void HAL_PWR_EnableSEVOnPend(void)
+{
+  /* Set SEVONPEND bit of Cortex System Control Register */
+  SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk));
+}
+
+
+/**
+  * @brief Disables CORTEX M4 SEVONPEND bit. 
+  * @note Clears SEVONPEND bit of SCR register. When this bit is set, this causes 
+  *       WFE to wake up when an interrupt moves from inactive to pended.         
+  * @retval None
+  */
+void HAL_PWR_DisableSEVOnPend(void)
+{
+  /* Clear SEVONPEND bit of Cortex System Control Register */
+  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk));
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_PWR_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_pwr_ex.c

@@ -0,0 +1,274 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_pwr_ex.c
+  * @author  MCD Application Team
+  * @brief   Extended PWR HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the Power Controller (PWR) peripheral:
+  *           + Extended Initialization and de-initialization functions
+  *           + Extended Peripheral Control functions
+  *         
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup PWREx PWREx
+  * @brief    PWREx HAL module driver
+  * @{
+  */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @defgroup PWREx_Private_Constants PWREx Private Constants
+  * @{
+  */
+#define PVD_MODE_IT               (0x00010000U)
+#define PVD_MODE_EVT              (0x00020000U)
+#define PVD_RISING_EDGE           (0x00000001U)
+#define PVD_FALLING_EDGE          (0x00000002U)
+/**
+  * @}
+  */
+ 
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Exported functions ---------------------------------------------------------*/
+
+/** @defgroup PWREx_Exported_Functions PWREx Exported Functions
+  * @{
+  */
+
+/** @defgroup PWREx_Exported_Functions_Group1 Peripheral Extended Control Functions
+  *  @brief   Extended Peripheral Control functions
+  *
+@verbatim
+
+ ===============================================================================
+                 ##### Peripheral extended control functions #####
+ ===============================================================================
+    
+    *** PVD configuration ***
+    =========================
+    [..]
+      (+) The PVD is used to monitor the VDD power supply by comparing it to a
+          threshold selected by the PVD Level (PLS[2:0] bits in the PWR_CR).
+      (+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower
+          than the PVD threshold. This event is internally connected to the EXTI
+          line16 and can generate an interrupt if enabled. This is done through
+          HAL_PWR_ConfigPVD(), HAL_PWR_EnablePVD() functions.
+      (+) The PVD is stopped in Standby mode.
+      -@- PVD is not available on STM32F030x4/x6/x8
+
+    *** VDDIO2 Monitor Configuration ***
+    ====================================
+    [..]
+      (+) VDDIO2 monitor is used to monitor the VDDIO2 power supply by comparing it 
+          to VREFInt Voltage
+      (+) This monitor is internally connected to the EXTI line31
+          and can generate an interrupt if enabled. This is done through
+          HAL_PWREx_EnableVddio2Monitor() function.
+      -@- VDDIO2 is available on STM32F07x/09x/04x
+                    
+@endverbatim
+  * @{
+  */
+
+#if defined (STM32F031x6) || defined (STM32F051x8) || \
+    defined (STM32F071xB) || defined (STM32F091xC) || \
+    defined (STM32F042x6) || defined (STM32F072xB)
+/**
+  * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD).
+  * @param sConfigPVD pointer to an PWR_PVDTypeDef structure that contains the configuration
+  *        information for the PVD.
+  * @note Refer to the electrical characteristics of your device datasheet for
+  *         more details about the voltage threshold corresponding to each
+  *         detection level.
+  * @retval None
+  */
+void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD)
+{
+  /* Check the parameters */
+  assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel));
+  assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode));
+
+  /* Set PLS[7:5] bits according to PVDLevel value */
+  MODIFY_REG(PWR->CR, PWR_CR_PLS, sConfigPVD->PVDLevel);
+  
+  /* Clear any previous config. Keep it clear if no event or IT mode is selected */
+  __HAL_PWR_PVD_EXTI_DISABLE_EVENT();
+  __HAL_PWR_PVD_EXTI_DISABLE_IT();
+  __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE();
+
+  /* Configure interrupt mode */
+  if((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT)
+  {
+    __HAL_PWR_PVD_EXTI_ENABLE_IT();
+  }
+  
+  /* Configure event mode */
+  if((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT)
+  {
+    __HAL_PWR_PVD_EXTI_ENABLE_EVENT();
+  }
+  
+  /* Configure the edge */
+  if((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE)
+  {
+    __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();
+  }
+  
+  if((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE)
+  {
+    __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();
+  }
+}
+
+/**
+  * @brief Enables the Power Voltage Detector(PVD).
+  * @retval None
+  */
+void HAL_PWR_EnablePVD(void)
+{
+  PWR->CR |= (uint32_t)PWR_CR_PVDE;
+}
+
+/**
+  * @brief Disables the Power Voltage Detector(PVD).
+  * @retval None
+  */
+void HAL_PWR_DisablePVD(void)
+{
+  PWR->CR &= ~((uint32_t)PWR_CR_PVDE);
+}
+
+/**
+  * @brief This function handles the PWR PVD interrupt request.
+  * @note This API should be called under the  PVD_IRQHandler() or PVD_VDDIO2_IRQHandler().
+  * @retval None
+  */
+void HAL_PWR_PVD_IRQHandler(void)
+{
+  /* Check PWR exti flag */
+  if(__HAL_PWR_PVD_EXTI_GET_FLAG() != RESET)
+  {
+    /* PWR PVD interrupt user callback */
+    HAL_PWR_PVDCallback();
+
+    /* Clear PWR Exti pending bit */
+    __HAL_PWR_PVD_EXTI_CLEAR_FLAG();
+  }
+}
+
+/**
+  * @brief PWR PVD interrupt callback
+  * @retval None
+  */
+__weak void HAL_PWR_PVDCallback(void)
+{
+  /* NOTE : This function Should not be modified, when the callback is needed,
+            the HAL_PWR_PVDCallback could be implemented in the user file
+   */
+}
+
+#endif /* defined (STM32F031x6) || defined (STM32F051x8) || */
+       /* defined (STM32F071xB) || defined (STM32F091xC) || */
+       /* defined (STM32F042x6) || defined (STM32F072xB)    */
+
+#if defined (STM32F042x6) || defined (STM32F048xx) || \
+    defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+    defined (STM32F091xC) || defined (STM32F098xx)
+/**
+  * @brief Enable VDDIO2 monitor: enable Exti 31 and falling edge detection.
+  * @note If Exti 31 is enable correlty and VDDIO2 voltage goes below Vrefint,
+          an interrupt is generated Irq line 1.
+          NVIS has to be enable by user.
+  * @retval None
+  */
+void HAL_PWREx_EnableVddio2Monitor(void)
+{
+  __HAL_PWR_VDDIO2_EXTI_ENABLE_IT();
+  __HAL_PWR_VDDIO2_EXTI_ENABLE_FALLING_EDGE();
+}
+
+/**
+  * @brief Disable the Vddio2 Monitor.
+  * @retval None
+  */
+void HAL_PWREx_DisableVddio2Monitor(void)
+{
+  __HAL_PWR_VDDIO2_EXTI_DISABLE_IT();
+  __HAL_PWR_VDDIO2_EXTI_DISABLE_FALLING_EDGE();
+
+}
+
+/**
+  * @brief This function handles the PWR Vddio2 monitor interrupt request.
+  * @note This API should be called under the VDDIO2_IRQHandler() PVD_VDDIO2_IRQHandler().
+  * @retval None
+  */
+void HAL_PWREx_Vddio2Monitor_IRQHandler(void)
+{
+  /* Check PWR exti flag */
+  if(__HAL_PWR_VDDIO2_EXTI_GET_FLAG() != RESET)
+  {
+    /* PWR Vddio2 monitor interrupt user callback */
+    HAL_PWREx_Vddio2MonitorCallback();
+
+    /* Clear PWR Exti pending bit */
+    __HAL_PWR_VDDIO2_EXTI_CLEAR_FLAG();
+  }
+}
+
+/**
+  * @brief PWR Vddio2 Monitor interrupt callback
+  * @retval None
+  */
+__weak void HAL_PWREx_Vddio2MonitorCallback(void)
+{
+  /* NOTE : This function Should not be modified, when the callback is needed,
+            the HAL_PWREx_Vddio2MonitorCallback could be implemented in the user file
+   */
+}
+
+#endif /* defined (STM32F042x6) || defined (STM32F048xx) || \
+          defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
+          defined (STM32F091xC) || defined (STM32F098xx) */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_PWR_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LED/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_rcc_ex.c

@@ -0,0 +1,964 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_rcc_ex.c
+  * @author  MCD Application Team
+  * @brief   Extended RCC HAL module driver.
+  *          This file provides firmware functions to manage the following 
+  *          functionalities RCC extension peripheral:
+  *           + Extended Peripheral Control functions
+  *           + Extended Clock Recovery System Control functions
+  *
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+  * @{
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+
+/** @defgroup RCCEx RCCEx
+  * @brief RCC Extension HAL module driver.
+  * @{
+  */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+#if defined(CRS)
+/** @defgroup RCCEx_Private_Constants RCCEx Private Constants
+  * @{
+  */
+/* Bit position in register */
+#define CRS_CFGR_FELIM_BITNUMBER    16
+#define CRS_CR_TRIM_BITNUMBER       8
+#define CRS_ISR_FECAP_BITNUMBER     16
+/**
+  * @}
+  */
+#endif /* CRS */
+  
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup RCCEx_Private_Macros RCCEx Private Macros
+  * @{
+  */
+/**
+  * @}
+  */
+
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup RCCEx_Exported_Functions RCCEx Exported Functions
+  * @{
+  */
+
+/** @defgroup RCCEx_Exported_Functions_Group1 Extended Peripheral Control functions 
+  * @brief    Extended Peripheral Control functions
+ *
+@verbatim
+ ===============================================================================
+                ##### Extended Peripheral Control functions  #####
+ ===============================================================================  
+    [..]
+    This subsection provides a set of functions allowing to control the RCC Clocks 
+    frequencies.
+    [..] 
+    (@) Important note: Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to
+        select the RTC clock source; in this case the Backup domain will be reset in  
+        order to modify the RTC Clock source, as consequence RTC registers (including 
+        the backup registers) are set to their reset values.
+      
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Initializes the RCC extended peripherals clocks according to the specified
+  *         parameters in the RCC_PeriphCLKInitTypeDef.
+  * @param  PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that
+  *         contains the configuration information for the Extended Peripherals clocks
+  *         (USART, RTC, I2C, CEC and USB).
+  *
+  * @note   Care must be taken when @ref HAL_RCCEx_PeriphCLKConfig() is used to select 
+  *         the RTC clock source; in this case the Backup domain will be reset in  
+  *         order to modify the RTC Clock source, as consequence RTC registers (including 
+  *         the backup registers) and RCC_BDCR register are set to their reset values.
+  *
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef  *PeriphClkInit)
+{
+  uint32_t tickstart = 0U;
+  uint32_t temp_reg = 0U;
+
+  /* Check the parameters */
+  assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection));
+  
+  /*---------------------------- RTC configuration -------------------------------*/
+  if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC))
+  {
+    /* check for RTC Parameters used to output RTCCLK */
+    assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection));
+    
+    FlagStatus       pwrclkchanged = RESET;
+
+    /* As soon as function is called to change RTC clock source, activation of the 
+       power domain is done. */
+    /* Requires to enable write access to Backup Domain of necessary */
+    if(__HAL_RCC_PWR_IS_CLK_DISABLED())
+    {
+    __HAL_RCC_PWR_CLK_ENABLE();
+      pwrclkchanged = SET;
+    }
+    
+    if(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP))
+    {
+      /* Enable write access to Backup domain */
+      SET_BIT(PWR->CR, PWR_CR_DBP);
+      
+      /* Wait for Backup domain Write protection disable */
+      tickstart = HAL_GetTick();
+      
+      while(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP))
+      {
+        if((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE)
+        {
+          return HAL_TIMEOUT;
+        }
+      }
+    }
+    
+    /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ 
+    temp_reg = (RCC->BDCR & RCC_BDCR_RTCSEL);
+    if((temp_reg != 0x00000000U) && (temp_reg != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL)))
+    {
+      /* Store the content of BDCR register before the reset of Backup Domain */
+      temp_reg = (RCC->BDCR & ~(RCC_BDCR_RTCSEL));
+      /* RTC Clock selection can be changed only if the Backup Domain is reset */
+      __HAL_RCC_BACKUPRESET_FORCE();
+      __HAL_RCC_BACKUPRESET_RELEASE();
+      /* Restore the Content of BDCR register */
+      RCC->BDCR = temp_reg;
+      
+      /* Wait for LSERDY if LSE was enabled */
+      if (HAL_IS_BIT_SET(temp_reg, RCC_BDCR_LSEON))
+      {
+        /* Get Start Tick */
+        tickstart = HAL_GetTick();
+        
+        /* Wait till LSE is ready */  
+        while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET)
+        {
+          if((HAL_GetTick() - tickstart) > RCC_LSE_TIMEOUT_VALUE)
+          {
+            return HAL_TIMEOUT;
+          }
+        }
+      }
+    }
+    __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection);
+
+    /* Require to disable power clock if necessary */
+    if(pwrclkchanged == SET)
+    {
+      __HAL_RCC_PWR_CLK_DISABLE();
+    }
+  }
+
+  /*------------------------------- USART1 Configuration ------------------------*/ 
+  if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USART1) == RCC_PERIPHCLK_USART1)
+  {
+    /* Check the parameters */
+    assert_param(IS_RCC_USART1CLKSOURCE(PeriphClkInit->Usart1ClockSelection));
+    
+    /* Configure the USART1 clock source */
+    __HAL_RCC_USART1_CONFIG(PeriphClkInit->Usart1ClockSelection);
+  }
+  
+#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx)\
+ || defined(STM32F091xC) || defined(STM32F098xx)
+  /*----------------------------- USART2 Configuration --------------------------*/ 
+  if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USART2) == RCC_PERIPHCLK_USART2)
+  {
+    /* Check the parameters */
+    assert_param(IS_RCC_USART2CLKSOURCE(PeriphClkInit->Usart2ClockSelection));
+    
+    /* Configure the USART2 clock source */
+    __HAL_RCC_USART2_CONFIG(PeriphClkInit->Usart2ClockSelection);
+  }
+#endif /* STM32F071xB || STM32F072xB || STM32F078xx || */
+       /* STM32F091xC || STM32F098xx */
+
+#if defined(STM32F091xC) || defined(STM32F098xx)
+  /*----------------------------- USART3 Configuration --------------------------*/ 
+  if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USART3) == RCC_PERIPHCLK_USART3)
+  {
+    /* Check the parameters */
+    assert_param(IS_RCC_USART3CLKSOURCE(PeriphClkInit->Usart3ClockSelection));
+    
+    /* Configure the USART3 clock source */
+    __HAL_RCC_USART3_CONFIG(PeriphClkInit->Usart3ClockSelection);
+  }
+#endif /* STM32F091xC || STM32F098xx */  
+
+  /*------------------------------ I2C1 Configuration ------------------------*/ 
+  if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2C1) == RCC_PERIPHCLK_I2C1)
+  {
+    /* Check the parameters */
+    assert_param(IS_RCC_I2C1CLKSOURCE(PeriphClkInit->I2c1ClockSelection));
+    
+    /* Configure the I2C1 clock source */
+    __HAL_RCC_I2C1_CONFIG(PeriphClkInit->I2c1ClockSelection);
+  }
+
+#if defined(STM32F042x6) || defined(STM32F048xx) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F070xB) || defined(STM32F070x6)
+  /*------------------------------ USB Configuration ------------------------*/ 
+  if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USB) == RCC_PERIPHCLK_USB)
+  {
+    /* Check the parameters */
+    assert_param(IS_RCC_USBCLKSOURCE(PeriphClkInit->UsbClockSelection));
+    
+    /* Configure the USB clock source */
+    __HAL_RCC_USB_CONFIG(PeriphClkInit->UsbClockSelection);
+  }
+#endif /* STM32F042x6 || STM32F048xx || STM32F072xB || STM32F078xx || STM32F070xB || STM32F070x6 */
+
+#if defined(STM32F042x6) || defined(STM32F048xx)\
+ || defined(STM32F051x8) || defined(STM32F058xx)\
+ || defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx)\
+ || defined(STM32F091xC) || defined(STM32F098xx)
+  /*------------------------------ CEC clock Configuration -------------------*/ 
+  if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CEC) == RCC_PERIPHCLK_CEC)
+  {
+    /* Check the parameters */
+    assert_param(IS_RCC_CECCLKSOURCE(PeriphClkInit->CecClockSelection));
+    
+    /* Configure the CEC clock source */
+    __HAL_RCC_CEC_CONFIG(PeriphClkInit->CecClockSelection);
+  }
+#endif /* STM32F042x6 || STM32F048xx ||                */
+       /* STM32F051x8 || STM32F058xx ||                */
+       /* STM32F071xB || STM32F072xB || STM32F078xx || */
+       /* STM32F091xC || STM32F098xx */
+  
+  return HAL_OK;
+}
+
+/**
+  * @brief  Get the RCC_ClkInitStruct according to the internal
+  * RCC configuration registers.
+  * @param  PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that
+  *         returns the configuration information for the Extended Peripherals clocks
+  *         (USART, RTC, I2C, CEC and USB).
+  * @retval None
+  */
+void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef  *PeriphClkInit)
+{
+  /* Set all possible values for the extended clock type parameter------------*/
+  /* Common part first */
+  PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_USART1 | RCC_PERIPHCLK_I2C1   | RCC_PERIPHCLK_RTC;  
+  /* Get the RTC configuration --------------------------------------------*/
+  PeriphClkInit->RTCClockSelection = __HAL_RCC_GET_RTC_SOURCE();
+  /* Get the USART1 clock configuration --------------------------------------------*/
+  PeriphClkInit->Usart1ClockSelection = __HAL_RCC_GET_USART1_SOURCE();
+  /* Get the I2C1 clock source -----------------------------------------------*/
+  PeriphClkInit->I2c1ClockSelection = __HAL_RCC_GET_I2C1_SOURCE();
+
+#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx)\
+ || defined(STM32F091xC) || defined(STM32F098xx)
+  PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_USART2;
+  /* Get the USART2 clock source ---------------------------------------------*/
+  PeriphClkInit->Usart2ClockSelection = __HAL_RCC_GET_USART2_SOURCE();
+#endif /* STM32F071xB || STM32F072xB || STM32F078xx || */
+       /* STM32F091xC || STM32F098xx */
+
+#if defined(STM32F091xC) || defined(STM32F098xx)
+  PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_USART3;
+  /* Get the USART3 clock source ---------------------------------------------*/
+  PeriphClkInit->Usart3ClockSelection = __HAL_RCC_GET_USART3_SOURCE();
+#endif /* STM32F091xC || STM32F098xx */
+
+#if defined(STM32F042x6) || defined(STM32F048xx) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F070xB) || defined(STM32F070x6)
+  PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_USB;
+  /* Get the USB clock source ---------------------------------------------*/
+  PeriphClkInit->UsbClockSelection = __HAL_RCC_GET_USB_SOURCE();
+#endif /* STM32F042x6 || STM32F048xx || STM32F072xB || STM32F078xx || STM32F070xB || STM32F070x6 */
+
+#if defined(STM32F042x6) || defined(STM32F048xx)\
+ || defined(STM32F051x8) || defined(STM32F058xx)\
+ || defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx)\
+ || defined(STM32F091xC) || defined(STM32F098xx)
+  PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_CEC;
+  /* Get the CEC clock source ------------------------------------------------*/
+  PeriphClkInit->CecClockSelection = __HAL_RCC_GET_CEC_SOURCE();
+#endif /* STM32F042x6 || STM32F048xx ||                */
+       /* STM32F051x8 || STM32F058xx ||                */
+       /* STM32F071xB || STM32F072xB || STM32F078xx || */
+       /* STM32F091xC || STM32F098xx */
+
+}
+
+/**
+  * @brief  Returns the peripheral clock frequency
+  * @note   Returns 0 if peripheral clock is unknown
+  * @param  PeriphClk Peripheral clock identifier
+  *         This parameter can be one of the following values:
+  *            @arg @ref RCC_PERIPHCLK_RTC     RTC peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_USART1  USART1 peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_I2C1    I2C1 peripheral clock
+  @if STM32F042x6
+  *            @arg @ref RCC_PERIPHCLK_USB     USB peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_CEC     CEC peripheral clock
+  @endif
+  @if STM32F048xx
+  *            @arg @ref RCC_PERIPHCLK_USB     USB peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_CEC     CEC peripheral clock
+  @endif
+  @if STM32F051x8
+  *            @arg @ref RCC_PERIPHCLK_CEC     CEC peripheral clock
+  @endif
+  @if STM32F058xx
+  *            @arg @ref RCC_PERIPHCLK_CEC     CEC peripheral clock
+  @endif
+  @if STM32F070x6
+  *            @arg @ref RCC_PERIPHCLK_USB     USB peripheral clock
+  @endif
+  @if STM32F070xB
+  *            @arg @ref RCC_PERIPHCLK_USB     USB peripheral clock
+  @endif
+  @if STM32F071xB
+  *            @arg @ref RCC_PERIPHCLK_USART2  USART2 peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_CEC     CEC peripheral clock
+  @endif
+  @if STM32F072xB
+  *            @arg @ref RCC_PERIPHCLK_USART2  USART2 peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_USB     USB peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_CEC     CEC peripheral clock
+  @endif
+  @if STM32F078xx
+  *            @arg @ref RCC_PERIPHCLK_USART2  USART2 peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_USB     USB peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_CEC     CEC peripheral clock
+  @endif
+  @if STM32F091xC
+  *            @arg @ref RCC_PERIPHCLK_USART2  USART2 peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_USART3  USART2 peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_CEC     CEC peripheral clock
+  @endif
+  @if STM32F098xx
+  *            @arg @ref RCC_PERIPHCLK_USART2  USART2 peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_USART3  USART2 peripheral clock
+  *            @arg @ref RCC_PERIPHCLK_CEC     CEC peripheral clock
+  @endif
+  * @retval Frequency in Hz (0: means that no available frequency for the peripheral)
+  */
+uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk)
+{
+  /* frequency == 0 : means that no available frequency for the peripheral */
+  uint32_t frequency = 0U;
+  
+  uint32_t srcclk = 0U;
+#if defined(USB)
+  uint32_t pllmull = 0U, pllsource = 0U, predivfactor = 0U;
+#endif /* USB */
+
+  /* Check the parameters */
+  assert_param(IS_RCC_PERIPHCLOCK(PeriphClk));
+  
+  switch (PeriphClk)
+  {
+  case RCC_PERIPHCLK_RTC:
+    {
+      /* Get the current RTC source */
+      srcclk = __HAL_RCC_GET_RTC_SOURCE();
+
+      /* Check if LSE is ready and if RTC clock selection is LSE */
+      if ((srcclk == RCC_RTCCLKSOURCE_LSE) && (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSERDY)))
+      {
+        frequency = LSE_VALUE;
+      }
+      /* Check if LSI is ready and if RTC clock selection is LSI */
+      else if ((srcclk == RCC_RTCCLKSOURCE_LSI) && (HAL_IS_BIT_SET(RCC->CSR, RCC_CSR_LSIRDY)))
+      {
+        frequency = LSI_VALUE;
+      }
+      /* Check if HSE is ready  and if RTC clock selection is HSI_DIV32*/
+      else if ((srcclk == RCC_RTCCLKSOURCE_HSE_DIV32) && (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSERDY)))
+      {
+        frequency = HSE_VALUE / 32U;
+      }
+      break;
+    }
+  case RCC_PERIPHCLK_USART1:
+    {
+      /* Get the current USART1 source */
+      srcclk = __HAL_RCC_GET_USART1_SOURCE();
+
+      /* Check if USART1 clock selection is PCLK1 */
+      if (srcclk == RCC_USART1CLKSOURCE_PCLK1)
+      {
+        frequency = HAL_RCC_GetPCLK1Freq();
+      }
+      /* Check if HSI is ready and if USART1 clock selection is HSI */
+      else if ((srcclk == RCC_USART1CLKSOURCE_HSI) && (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSIRDY)))
+      {
+        frequency = HSI_VALUE;
+      }
+      /* Check if USART1 clock selection is SYSCLK */
+      else if (srcclk == RCC_USART1CLKSOURCE_SYSCLK)
+      {
+        frequency = HAL_RCC_GetSysClockFreq();
+      }
+      /* Check if LSE is ready  and if USART1 clock selection is LSE */
+      else if ((srcclk == RCC_USART1CLKSOURCE_LSE) && (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSERDY)))
+      {
+        frequency = LSE_VALUE;
+      }
+      break;
+    }
+#if defined(RCC_CFGR3_USART2SW)
+  case RCC_PERIPHCLK_USART2:
+    {
+      /* Get the current USART2 source */
+      srcclk = __HAL_RCC_GET_USART2_SOURCE();
+
+      /* Check if USART2 clock selection is PCLK1 */
+      if (srcclk == RCC_USART2CLKSOURCE_PCLK1)
+      {
+        frequency = HAL_RCC_GetPCLK1Freq();
+      }
+      /* Check if HSI is ready and if USART2 clock selection is HSI */
+      else if ((srcclk == RCC_USART2CLKSOURCE_HSI) && (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSIRDY)))
+      {
+        frequency = HSI_VALUE;
+      }
+      /* Check if USART2 clock selection is SYSCLK */
+      else if (srcclk == RCC_USART2CLKSOURCE_SYSCLK)
+      {
+        frequency = HAL_RCC_GetSysClockFreq();
+      }
+      /* Check if LSE is ready  and if USART2 clock selection is LSE */
+      else if ((srcclk == RCC_USART2CLKSOURCE_LSE) && (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSERDY)))
+      {
+        frequency = LSE_VALUE;
+      }
+      break;
+    }
+#endif /* RCC_CFGR3_USART2SW */
+#if defined(RCC_CFGR3_USART3SW)
+  case RCC_PERIPHCLK_USART3:
+    {
+      /* Get the current USART3 source */
+      srcclk = __HAL_RCC_GET_USART3_SOURCE();
+
+      /* Check if USART3 clock selection is PCLK1 */
+      if (srcclk == RCC_USART3CLKSOURCE_PCLK1)
+      {
+        frequency = HAL_RCC_GetPCLK1Freq();
+      }
+      /* Check if HSI is ready and if USART3 clock selection is HSI */
+      else if ((srcclk == RCC_USART3CLKSOURCE_HSI) && (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSIRDY)))
+      {
+        frequency = HSI_VALUE;
+      }
+      /* Check if USART3 clock selection is SYSCLK */
+      else if (srcclk == RCC_USART3CLKSOURCE_SYSCLK)
+      {
+        frequency = HAL_RCC_GetSysClockFreq();
+      }
+      /* Check if LSE is ready  and if USART3 clock selection is LSE */
+      else if ((srcclk == RCC_USART3CLKSOURCE_LSE) && (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSERDY)))
+      {
+        frequency = LSE_VALUE;
+      }
+      break;
+    }
+#endif /* RCC_CFGR3_USART3SW */
+  case RCC_PERIPHCLK_I2C1:
+    {
+      /* Get the current I2C1 source */
+      srcclk = __HAL_RCC_GET_I2C1_SOURCE();
+
+      /* Check if HSI is ready and if I2C1 clock selection is HSI */
+      if ((srcclk == RCC_I2C1CLKSOURCE_HSI) && (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSIRDY)))
+      {
+        frequency = HSI_VALUE;
+      }
+      /* Check if I2C1 clock selection is SYSCLK */
+      else if (srcclk == RCC_I2C1CLKSOURCE_SYSCLK)
+      {
+        frequency = HAL_RCC_GetSysClockFreq();
+      }
+      break;
+    }
+#if defined(USB)
+  case RCC_PERIPHCLK_USB:
+    {
+      /* Get the current USB source */
+      srcclk = __HAL_RCC_GET_USB_SOURCE();
+
+      /* Check if PLL is ready and if USB clock selection is PLL */
+      if ((srcclk == RCC_USBCLKSOURCE_PLL) && (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLLRDY)))
+      {
+        /* Get PLL clock source and multiplication factor ----------------------*/
+        pllmull      = RCC->CFGR & RCC_CFGR_PLLMUL;
+        pllsource    = RCC->CFGR & RCC_CFGR_PLLSRC;
+        pllmull      = (pllmull >> RCC_CFGR_PLLMUL_BITNUMBER) + 2U;
+        predivfactor = (RCC->CFGR2 & RCC_CFGR2_PREDIV) + 1U;
+
+        if (pllsource == RCC_CFGR_PLLSRC_HSE_PREDIV)
+        {
+          /* HSE used as PLL clock source : frequency = HSE/PREDIV * PLLMUL */
+          frequency = (HSE_VALUE/predivfactor) * pllmull;
+        }
+#if defined(RCC_CR2_HSI48ON)
+        else if (pllsource == RCC_CFGR_PLLSRC_HSI48_PREDIV)
+        {
+          /* HSI48 used as PLL clock source : frequency = HSI48/PREDIV * PLLMUL */
+          frequency = (HSI48_VALUE / predivfactor) * pllmull;
+        }
+#endif /* RCC_CR2_HSI48ON */
+        else
+        {
+#if defined(STM32F042x6) || defined(STM32F048xx) || defined(STM32F078xx) || defined(STM32F072xB) || defined(STM32F070xB)
+          /* HSI used as PLL clock source : frequency = HSI/PREDIV * PLLMUL */
+          frequency = (HSI_VALUE / predivfactor) * pllmull;
+#else
+          /* HSI used as PLL clock source : frequency = HSI/2U * PLLMUL */
+          frequency = (HSI_VALUE >> 1U) * pllmull;
+#endif /* STM32F042x6 || STM32F048xx || STM32F072xB || STM32F078xx || STM32F070xB */
+        }
+      }
+#if defined(RCC_CR2_HSI48ON)
+      /* Check if HSI48 is ready and if USB clock selection is HSI48 */
+      else if ((srcclk == RCC_USBCLKSOURCE_HSI48) && (HAL_IS_BIT_SET(RCC->CR2, RCC_CR2_HSI48RDY)))
+      {
+        frequency = HSI48_VALUE;
+      }
+#endif /* RCC_CR2_HSI48ON */
+      break;
+    }
+#endif /* USB */
+#if defined(CEC)
+  case RCC_PERIPHCLK_CEC:
+    {
+      /* Get the current CEC source */
+      srcclk = __HAL_RCC_GET_CEC_SOURCE();
+
+      /* Check if HSI is ready and if CEC clock selection is HSI */
+      if ((srcclk == RCC_CECCLKSOURCE_HSI) && (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSIRDY)))
+      {
+        frequency = HSI_VALUE;
+      }
+      /* Check if LSE is ready  and if CEC clock selection is LSE */
+      else if ((srcclk == RCC_CECCLKSOURCE_LSE) && (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSERDY)))
+      {
+        frequency = LSE_VALUE;
+      }
+      break;
+    }
+#endif /* CEC */
+  default: 
+    {
+      break;
+    }
+  }
+  return(frequency);
+}
+
+/**
+  * @}
+  */
+
+#if defined(CRS)
+
+/** @defgroup RCCEx_Exported_Functions_Group3 Extended Clock Recovery System Control functions 
+ *  @brief  Extended Clock Recovery System Control functions
+ *
+@verbatim
+ ===============================================================================
+                ##### Extended Clock Recovery System Control functions  #####
+ ===============================================================================
+    [..]
+      For devices with Clock Recovery System feature (CRS), RCC Extension HAL driver can be used as follows:
+
+      (#) In System clock config, HSI48 needs to be enabled
+
+      (#) Enable CRS clock in IP MSP init which will use CRS functions
+
+      (#) Call CRS functions as follows:
+          (##) Prepare synchronization configuration necessary for HSI48 calibration
+              (+++) Default values can be set for frequency Error Measurement (reload and error limit)
+                        and also HSI48 oscillator smooth trimming.
+              (+++) Macro @ref __HAL_RCC_CRS_RELOADVALUE_CALCULATE can be also used to calculate 
+                        directly reload value with target and synchronization frequencies values
+          (##) Call function @ref HAL_RCCEx_CRSConfig which
+              (+++) Reset CRS registers to their default values.
+              (+++) Configure CRS registers with synchronization configuration 
+              (+++) Enable automatic calibration and frequency error counter feature
+           Note: When using USB LPM (Link Power Management) and the device is in Sleep mode, the
+           periodic USB SOF will not be generated by the host. No SYNC signal will therefore be
+           provided to the CRS to calibrate the HSI48 on the run. To guarantee the required clock
+           precision after waking up from Sleep mode, the LSE or reference clock on the GPIOs
+           should be used as SYNC signal.
+
+          (##) A polling function is provided to wait for complete synchronization
+              (+++) Call function @ref HAL_RCCEx_CRSWaitSynchronization()
+              (+++) According to CRS status, user can decide to adjust again the calibration or continue
+                        application if synchronization is OK
+              
+      (#) User can retrieve information related to synchronization in calling function
+            @ref HAL_RCCEx_CRSGetSynchronizationInfo()
+
+      (#) Regarding synchronization status and synchronization information, user can try a new calibration
+           in changing synchronization configuration and call again HAL_RCCEx_CRSConfig.
+           Note: When the SYNC event is detected during the downcounting phase (before reaching the zero value), 
+           it means that the actual frequency is lower than the target (and so, that the TRIM value should be 
+           incremented), while when it is detected during the upcounting phase it means that the actual frequency 
+           is higher (and that the TRIM value should be decremented).
+
+      (#) In interrupt mode, user can resort to the available macros (__HAL_RCC_CRS_XXX_IT). Interrupts will go 
+          through CRS Handler (RCC_IRQn/RCC_IRQHandler)
+              (++) Call function @ref HAL_RCCEx_CRSConfig()
+              (++) Enable RCC_IRQn (thanks to NVIC functions)
+              (++) Enable CRS interrupt (@ref __HAL_RCC_CRS_ENABLE_IT)
+              (++) Implement CRS status management in the following user callbacks called from 
+                   HAL_RCCEx_CRS_IRQHandler():
+                   (+++) @ref HAL_RCCEx_CRS_SyncOkCallback()
+                   (+++) @ref HAL_RCCEx_CRS_SyncWarnCallback()
+                   (+++) @ref HAL_RCCEx_CRS_ExpectedSyncCallback()
+                   (+++) @ref HAL_RCCEx_CRS_ErrorCallback()
+
+      (#) To force a SYNC EVENT, user can use the function @ref HAL_RCCEx_CRSSoftwareSynchronizationGenerate().
+          This function can be called before calling @ref HAL_RCCEx_CRSConfig (for instance in Systick handler)
+            
+@endverbatim
+ * @{
+ */
+
+/**
+  * @brief  Start automatic synchronization for polling mode
+  * @param  pInit Pointer on RCC_CRSInitTypeDef structure
+  * @retval None
+  */
+void HAL_RCCEx_CRSConfig(RCC_CRSInitTypeDef *pInit)
+{
+  uint32_t value = 0U;
+  
+  /* Check the parameters */
+  assert_param(IS_RCC_CRS_SYNC_DIV(pInit->Prescaler));
+  assert_param(IS_RCC_CRS_SYNC_SOURCE(pInit->Source));
+  assert_param(IS_RCC_CRS_SYNC_POLARITY(pInit->Polarity));
+  assert_param(IS_RCC_CRS_RELOADVALUE(pInit->ReloadValue));
+  assert_param(IS_RCC_CRS_ERRORLIMIT(pInit->ErrorLimitValue));
+  assert_param(IS_RCC_CRS_HSI48CALIBRATION(pInit->HSI48CalibrationValue));
+
+  /* CONFIGURATION */
+
+  /* Before configuration, reset CRS registers to their default values*/
+  __HAL_RCC_CRS_FORCE_RESET();
+  __HAL_RCC_CRS_RELEASE_RESET();
+
+  /* Set the SYNCDIV[2:0] bits according to Prescaler value */
+  /* Set the SYNCSRC[1:0] bits according to Source value */
+  /* Set the SYNCSPOL bit according to Polarity value */
+  value = (pInit->Prescaler | pInit->Source | pInit->Polarity);
+  /* Set the RELOAD[15:0] bits according to ReloadValue value */
+  value |= pInit->ReloadValue;
+  /* Set the FELIM[7:0] bits according to ErrorLimitValue value */
+  value |= (pInit->ErrorLimitValue << CRS_CFGR_FELIM_BITNUMBER);
+  WRITE_REG(CRS->CFGR, value);
+
+  /* Adjust HSI48 oscillator smooth trimming */
+  /* Set the TRIM[5:0] bits according to RCC_CRS_HSI48CalibrationValue value */
+  MODIFY_REG(CRS->CR, CRS_CR_TRIM, (pInit->HSI48CalibrationValue << CRS_CR_TRIM_BITNUMBER));
+  
+  /* START AUTOMATIC SYNCHRONIZATION*/
+  
+  /* Enable Automatic trimming & Frequency error counter */
+  SET_BIT(CRS->CR, CRS_CR_AUTOTRIMEN | CRS_CR_CEN);
+}
+
+/**
+  * @brief  Generate the software synchronization event
+  * @retval None
+  */
+void HAL_RCCEx_CRSSoftwareSynchronizationGenerate(void)
+{
+  SET_BIT(CRS->CR, CRS_CR_SWSYNC);
+}
+
+/**
+  * @brief  Return synchronization info 
+  * @param  pSynchroInfo Pointer on RCC_CRSSynchroInfoTypeDef structure
+  * @retval None
+  */
+void HAL_RCCEx_CRSGetSynchronizationInfo(RCC_CRSSynchroInfoTypeDef *pSynchroInfo)
+{
+  /* Check the parameter */
+  assert_param(pSynchroInfo != NULL);
+  
+  /* Get the reload value */
+  pSynchroInfo->ReloadValue = (uint32_t)(READ_BIT(CRS->CFGR, CRS_CFGR_RELOAD));
+  
+  /* Get HSI48 oscillator smooth trimming */
+  pSynchroInfo->HSI48CalibrationValue = (uint32_t)(READ_BIT(CRS->CR, CRS_CR_TRIM) >> CRS_CR_TRIM_BITNUMBER);
+
+  /* Get Frequency error capture */
+  pSynchroInfo->FreqErrorCapture = (uint32_t)(READ_BIT(CRS->ISR, CRS_ISR_FECAP) >> CRS_ISR_FECAP_BITNUMBER);
+
+  /* Get Frequency error direction */
+  pSynchroInfo->FreqErrorDirection = (uint32_t)(READ_BIT(CRS->ISR, CRS_ISR_FEDIR));
+}
+
+/**
+* @brief Wait for CRS Synchronization status.
+* @param Timeout  Duration of the timeout
+* @note  Timeout is based on the maximum time to receive a SYNC event based on synchronization
+*        frequency.
+* @note    If Timeout set to HAL_MAX_DELAY, HAL_TIMEOUT will be never returned.
+* @retval Combination of Synchronization status
+*          This parameter can be a combination of the following values:
+*            @arg @ref RCC_CRS_TIMEOUT
+*            @arg @ref RCC_CRS_SYNCOK
+*            @arg @ref RCC_CRS_SYNCWARN
+*            @arg @ref RCC_CRS_SYNCERR
+*            @arg @ref RCC_CRS_SYNCMISS
+*            @arg @ref RCC_CRS_TRIMOVF
+*/
+uint32_t HAL_RCCEx_CRSWaitSynchronization(uint32_t Timeout)
+{
+  uint32_t crsstatus = RCC_CRS_NONE;
+  uint32_t tickstart = 0U;
+  
+  /* Get timeout */
+  tickstart = HAL_GetTick();
+  
+  /* Wait for CRS flag or timeout detection */
+  do
+  {
+    if(Timeout != HAL_MAX_DELAY)
+    {
+      if((Timeout == 0U) || ((HAL_GetTick() - tickstart) > Timeout))
+      {
+        crsstatus = RCC_CRS_TIMEOUT;
+      }
+    }
+    /* Check CRS SYNCOK flag  */
+    if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_SYNCOK))
+    {
+      /* CRS SYNC event OK */
+      crsstatus |= RCC_CRS_SYNCOK;
+    
+      /* Clear CRS SYNC event OK bit */
+      __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_SYNCOK);
+    }
+    
+    /* Check CRS SYNCWARN flag  */
+    if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_SYNCWARN))
+    {
+      /* CRS SYNC warning */
+      crsstatus |= RCC_CRS_SYNCWARN;
+    
+      /* Clear CRS SYNCWARN bit */
+      __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_SYNCWARN);
+    }
+    
+    /* Check CRS TRIM overflow flag  */
+    if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_TRIMOVF))
+    {
+      /* CRS SYNC Error */
+      crsstatus |= RCC_CRS_TRIMOVF;
+    
+      /* Clear CRS Error bit */
+      __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_TRIMOVF);
+    }
+    
+    /* Check CRS Error flag  */
+    if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_SYNCERR))
+    {
+      /* CRS SYNC Error */
+      crsstatus |= RCC_CRS_SYNCERR;
+    
+      /* Clear CRS Error bit */
+      __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_SYNCERR);
+    }
+    
+    /* Check CRS SYNC Missed flag  */
+    if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_SYNCMISS))
+    {
+      /* CRS SYNC Missed */
+      crsstatus |= RCC_CRS_SYNCMISS;
+    
+      /* Clear CRS SYNC Missed bit */
+      __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_SYNCMISS);
+    }
+    
+    /* Check CRS Expected SYNC flag  */
+    if(__HAL_RCC_CRS_GET_FLAG(RCC_CRS_FLAG_ESYNC))
+    {
+      /* frequency error counter reached a zero value */
+      __HAL_RCC_CRS_CLEAR_FLAG(RCC_CRS_FLAG_ESYNC);
+    }
+  } while(RCC_CRS_NONE == crsstatus);
+
+  return crsstatus;
+}
+
+/**
+  * @brief Handle the Clock Recovery System interrupt request.
+  * @retval None
+  */
+void HAL_RCCEx_CRS_IRQHandler(void)
+{
+  uint32_t crserror = RCC_CRS_NONE;
+  /* Get current IT flags and IT sources values */
+  uint32_t itflags = READ_REG(CRS->ISR);
+  uint32_t itsources = READ_REG(CRS->CR);
+
+  /* Check CRS SYNCOK flag  */
+  if(((itflags & RCC_CRS_FLAG_SYNCOK) != RESET) && ((itsources & RCC_CRS_IT_SYNCOK) != RESET))
+  {
+    /* Clear CRS SYNC event OK flag */
+    WRITE_REG(CRS->ICR, CRS_ICR_SYNCOKC);
+
+    /* user callback */
+    HAL_RCCEx_CRS_SyncOkCallback();
+  }
+  /* Check CRS SYNCWARN flag  */
+  else if(((itflags & RCC_CRS_FLAG_SYNCWARN) != RESET) && ((itsources & RCC_CRS_IT_SYNCWARN) != RESET))
+  {
+    /* Clear CRS SYNCWARN flag */
+    WRITE_REG(CRS->ICR, CRS_ICR_SYNCWARNC);
+
+    /* user callback */
+    HAL_RCCEx_CRS_SyncWarnCallback();
+  }
+  /* Check CRS Expected SYNC flag  */
+  else if(((itflags & RCC_CRS_FLAG_ESYNC) != RESET) && ((itsources & RCC_CRS_IT_ESYNC) != RESET))
+  {
+    /* frequency error counter reached a zero value */
+    WRITE_REG(CRS->ICR, CRS_ICR_ESYNCC);
+
+    /* user callback */
+    HAL_RCCEx_CRS_ExpectedSyncCallback();
+  }
+  /* Check CRS Error flags  */
+  else
+  {
+    if(((itflags & RCC_CRS_FLAG_ERR) != RESET) && ((itsources & RCC_CRS_IT_ERR) != RESET))
+    {
+      if((itflags & RCC_CRS_FLAG_SYNCERR) != RESET)
+      {
+        crserror |= RCC_CRS_SYNCERR;
+      }
+      if((itflags & RCC_CRS_FLAG_SYNCMISS) != RESET)
+      {
+        crserror |= RCC_CRS_SYNCMISS;
+      }
+      if((itflags & RCC_CRS_FLAG_TRIMOVF) != RESET)
+      {
+        crserror |= RCC_CRS_TRIMOVF;
+      }
+
+      /* Clear CRS Error flags */
+      WRITE_REG(CRS->ICR, CRS_ICR_ERRC);
+    
+      /* user error callback */
+      HAL_RCCEx_CRS_ErrorCallback(crserror);
+    }
+  }
+}
+
+/**
+  * @brief  RCCEx Clock Recovery System SYNCOK interrupt callback.
+  * @retval none
+  */
+__weak void HAL_RCCEx_CRS_SyncOkCallback(void)
+{
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the @ref HAL_RCCEx_CRS_SyncOkCallback should be implemented in the user file
+   */
+}
+
+/**
+  * @brief  RCCEx Clock Recovery System SYNCWARN interrupt callback.
+  * @retval none
+  */
+__weak void HAL_RCCEx_CRS_SyncWarnCallback(void)
+{
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the @ref HAL_RCCEx_CRS_SyncWarnCallback should be implemented in the user file
+   */
+}
+
+/**
+  * @brief  RCCEx Clock Recovery System Expected SYNC interrupt callback.
+  * @retval none
+  */
+__weak void HAL_RCCEx_CRS_ExpectedSyncCallback(void)
+{
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the @ref HAL_RCCEx_CRS_ExpectedSyncCallback should be implemented in the user file
+   */
+}
+
+/**
+  * @brief  RCCEx Clock Recovery System Error interrupt callback.
+  * @param  Error Combination of Error status. 
+  *         This parameter can be a combination of the following values:
+  *           @arg @ref RCC_CRS_SYNCERR
+  *           @arg @ref RCC_CRS_SYNCMISS
+  *           @arg @ref RCC_CRS_TRIMOVF
+  * @retval none
+  */
+__weak void HAL_RCCEx_CRS_ErrorCallback(uint32_t Error)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(Error);
+
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the @ref HAL_RCCEx_CRS_ErrorCallback should be implemented in the user file
+   */
+}
+
+/**
+  * @}
+  */
+
+#endif /* CRS */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/